Cisco 881w Manual

							 
1-111
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
8 SIM  Green / Yellow 
(one green blink 
followed by two 
yellow blinks)SIM in slot 0 is active, SIM in slot 1 is not.
Yellow / Green 
(one yellow blink 
followed by two 
green blinks)SIM in slot 1 is active, SIM in slot 0 is not.
Off / Green (two 
green blinks and 
then a pause)No SIM in slot 0, SIM present in slot 1.
Green / Off (slow 
green blink once 
and then a pause)SIM is present in slot0, no SIM in slot 1.
Off / Off No SIM present in either slots.
9 Service Green (Solid) Service is active and the corresponding LED is lit based 
on the service level which is active (2G, 3G, 3.5G, 3.7G, 
LTE).
Off No service.
10 RSSI Green (solid) Signal strength bars are indicated by the corresponding 
LEDs.
11 GPS Green (solid) Standalone GPS.
Green (slow 
blinking)GPS is acquiring signals.
Yellow (solid) Assisted GPS.
Yellow (slow 
blinking)Assisted GPS is acquiring signals.
Off GPS is not configured.
12 WWAN Green Module is powered on and connected, but not 
transmitting or receiving.
Green (slow 
blinking)Module is powered on and searching for connection.
Green (fast 
blinking)Module is transmitting or receiving.
Off Module is not powered.
Table 1-40 LED Descriptions for the Cisco C899G-LTE ISR (continued)
Number LED Color Description 
						

							 
1-112
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Figure 1-61 shows the back panel of the Cisco C899G-LTE ISR.
Figure 1-61 Back Panel of the Cisco C899G-LTE ISR 
						

							 
1-113
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
372527
12345678111312109
141516
1GE WAN interface9Power connector 
2GE WAN interface 10On/Off switch
3SFP port11Reset button
44G port 12Earth ground connection
5USB port 13Kensington security slot
6SIM slots 144G antenna connector—M1/DIV
78-port Gigabit Ethernet switch15Active GPS antenna connector
8Console/Auxiliary port16 4G antenna connector—M0/MAIN 
						

							 
1-114
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Cisco 890 Series Integrated Service Routers
This sections contains the following topics:
Cisco 891, Cisco 892, and Cisco 892F, page 1-114
Cisco C897VAB-K9, page 1-124
Cisco 891, Cisco 892, and Cisco 892F
The Cisco 891, Cisco 892, and Cisco 892F ISRs have the following features:
Integrated 8-port 10/100 Ethernet switch for connecting to the LAN
10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN
Separate console and auxiliary ports
(Optional) embedded Wi-Fi certified dual-radio 802.11a/b/g/n-compliant wireless AP
Optional 4-port PoE
NoteThe Cisco 890 Series ISRs can include an optional PoE module that provides power to 
802.3af-compliant devices connected to Ethernet ports 0 through 3. If this feature was not 
configured with the factory order, you must order and install it to enable the PoE function.
NoteOn a Cisco 891 series router, due to TCAM limitation, you can apply an ACL configuration on 
maximum 9 ports. If you apply the ACL configuration beyond 9 ports, the configuration will not 
be applied, and the router will display an error message.
Security feature card (SFC) socket
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB 
system memory in Cisco 891 and Cisco 892 ISRs, and a total of 1 GB system memory in 
Cisco 892F series ISRs
Three reverse-polarity Threaded Neill-Concelman (RP-TNC) connectors on the back panel for 
non-captive dual-band WLAN antenna (wireless models only)
Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9
GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only)
The following feature is located on the front panel of 
Two USB 2.0 ports 
						

							 
1-115
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Figure 1-62 shows the front panel details of the Cisco 890 Series router.
Figure 1-62 Front Panel of the Cisco 890 Series ISR
Figure 1-63 shows the back panel details of the Cisco 892W router. Non wireless routers do not have 
RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be 
available on your router. However, the feature locations are similar across all Cisco 890 series routers.
Figure 1-63 Back Panel of the Cisco 892W Router
1LEDs2USB ports
272367
12
1Antenna—Dipole swivel antenna attached to 
RP-TNC connectors (wireless models only)7PoE power connector for optional PoE 
module1
2Backup—Data BRI2 or V.923 port8Reset button
3Primary WAN port—FE and GE9Power connector
272369
1456891011723 
						

							 
1-116
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Figure 1-64 shows the location of the SFP port on a Cisco 892FW router.
Figure 1-64 SFP Port Location on a Cisco 892FW Router
Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
The Cisco 892FSP, Cisco 896VA, Cisco897VA (includes Cisco 897VA, Cisco 897VAM, Cisco 897VAW, 
Cisco 897VAMW), and Cisco 898EA routers have the following features:
Integrated 8-port 10/100/1000 Gigabit Ethernet switch for connecting to the LAN
Two 10/100/1000 GE ports for Cisco 892FSP
One 10/100/1000 GE port for Cisco 896VA, 897VA, and the Cisco 898EA. Either the SFP socket or 
the 10/100/1000 GE port can be active at a given time, but not both.
Single console and auxiliary ports for configuration and management
512 MB of on-board memory (upgrade option to 1 GB)
256 MB flash memory for Cisco 896VA, Cisco 897VA, and Cisco 898EA
One USB 2.0 port
Optional internal adapter for inline PoE on four switch ports for IP phones or external wireless 
access points for Cisco 896VA, Cisco 897VA, and Cisco 898EA models only. No PoE support on 
Cisco 892FSP. 4Auxiliary port10Earth ground connection
5Console port 11Kensington security slot
68-port 10/100 Ethernet switch
1. The Cisco 890 Series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected 
to Ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable 
the PoE function.
2. The Data BRI port is available only on the Cisco 892 Router models.
3. The V.92 port (not shown) is available only on the Cisco 891 Router models and is located between the console port and the 
Ethernet switch.
1SFP port2SFP LEDs
278179
Cisco 892F-W
SFP
EN
S
21 
						

							 
1-117
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
NoteThe Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have 
an SFC socket.
NoteTo upgrade DRAM memory from 512 MB to 1 GB on the Cisco 892FSP, Cisco 896VA, Cisco 897VA, 
and Cisco 898EA routers, you should enable the FL-8XX-512U1GB license.  
						

							 
1-118
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Figure 1-65 shows the back panel of the Cisco 892FSP Router. 
Figure 1-65 Back Panel of the Cisco 892FSP Router
Figure 1-66 shows the front panel of the Cisco 892FSP Router. 
Figure 1-66 Front Panel of the Cisco 892FSP Router
9 GE W A N8 GE W A N
SFP
8
12VD C        2.5ACONSOLE
AU XRESE T
Cisco 892FSP
284781
23456891071
1GE WAN interface6Power connector
2SFP port7On/Off switch
3USB port8Reset button
48-port Gigabit Ethernet switch9Earth ground connection
5Console/Auxiliary port10Kensington security slot
284782
1
1LEDs 
						

							 
1-119
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Figure 1-67 shows the back panel of the Cisco 896VA Router. 
Figure 1-67 Back Panel of the Cisco 896VA Router
Figure 1-68 shows the front panel of the Cisco 896VA and the Cisco 897VA routers. 
Figure 1-68 Front Panel of the Cisco 896VA and Cisco 897VA Routers
     7                        6     GELAN    5                       4
    3                        2          POE      1                       0
0 ISDN8 GE WAN
54VDC       1.2A
12VDC       2.5A
VDSL/ADSL
overISDN
CONSOLE
RESET
Cisco 896VA
12
1234589101167
344766
1ISDN7Power connector
2GE WAN interface8On/Off switch
3SFP port9Reset button
4USB port10Earth ground connection
58-port Gigabit Ethernet switch
111Kensington security slot
6Console/Auxiliary port12VDSL / ADSL over ISDN
1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured with 
the factory order, you must order and install it to enable the PoE function.
1
344765
1LEDs 
						

							 
1-120
Cisco Integrated Services Router Hardware Installation Guide
 
Chapter 1      Product Overview
  Cisco 860, 880, 890 Series
Figure 1-69 shows the back panel of the Cisco 897VA Router.
Figure 1-69 Back Panel of the Cisco 897VA Router
Figure 1-70 shows the back panel of the Cisco 897VAM Router.
Figure 1-70 Back Panel of the Cisco 897VAM Router
     7                        6     GELAN    5                       4
    3                        2          POE      1                       0
0 ISDN8 GE WAN
54VDC       1.2A
12VDC       2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
Cisco 897VA
344767
12
1234589101167
1ISDN7Power connector
2GE WAN interface8On/Off switch
3SFP port9Reset button
4USB port10Earth ground connection
58-port Gigabit Ethernet switch
111Kensington security slot
6Console/Auxiliary port12VDSL/ADSL over POTS
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with 
the factory order, you must order and install it to enable the PoE function.
     7                        6     GELAN    5                       4
    3                        2          POE      1                       0
8 GE WAN
54VDC       1.2A
12VDC       2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
344769
11
12347891056
1GE WAN interface7On/Off switch
2SFP port8Reset button
3USB port9Earth ground connection