Cisco 4507re Manual
Have a look at the manual Cisco 4507re Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
A-13 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W AC-Input Power Supply 1400 W Power Supply AC Power Cords Ta b l e A - 9 lists the specifications for the AC power cords that are available for the 1400 W AC-input power supply. The table includes a power plug illustration for each power cord. NoteAll 1400 W power supply power cords have an IEC60320/C19 appliance plug at one end. Table A-8 1400 W AC-Input Power Supply LEDs LED Meaning INPUT OK •Green—Source AC voltage is OK. (Input voltage is 85 VAC or greater.) •Off—Source AC voltage falls below 70 VAC, is not present, or the power supply is turned off. FAN OK •Green—Power supply fan is operating properly. •Off—Power supply fan failure is detected. OUTPUT FAIL •Red—Problem with one or more of the DC-output voltages of the power supply is detected. •Off—DC-output voltage with acceptable margins. NoteFor proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. Table A-9 1400 W AC-Input Power Supply Power Cords LocalePower Cord Part Number Length Cordset RatingAC Source Plug Ty p e Japan, North America CAB-US520-C19-US= (was CAB-7513AC=)14 ft (4.3 m) 20 A, 125 VAC NEMA 5-20 Australia, New ZealandCAB-A3112-C19-AUS= (was CAB-7513ACA=)14 ft (4.3 m) 15 A, 250 VAC SAA/3, AS/NZZS 3112-1993 120362 120356
A-14 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W AC-Input Power Supply Europe (except Italy)CAB-CEE77-C19-EU= (was CAB-7513ACE=)14 ft (4.3 m) 16 A, 250 VAC CEE 7/7 Italy CAB-C2316-C19-IT= (was CAB-7513ACI=)14 ft (4.3 m) 16 A, 250 VAC 1/3/16, CEI 23-16 United KingdomCAB-BS1363-C19-UK= (was CAB-7513ACU=)14 ft (4.3 m) 13 A, 250 VAC BS 89/13 BS 1363/A Argentina CAB-IR2073-C19-AR= (was CAB-7513ACR=)14 ft (4.3 m) 16 A, 250 VAC IRAM 2073 Japan, North America (locking) 200–240 VAC operationCAB-AC-2800W-TWLK= 13.6 ft (4.1 m)16 A, 250 VAC NEMA L6-20 Japan, North America (nonlocking) 200–240 VAC operationCAB-AC-2800W-6-20 13.2 ft (4.0 m)16 A, 250 VAC NEMA 6-20 non-locking Europe CAB-AC-2800W-EU= 13.2 ft (4.0 m)16 A, 250 VAC CEE 7/7 South Africa, IndiaCAB-BS546-C15-SA= (was CAB-7513ACSA)13.6 ft (4.1 m)16 A, 250 VAC BS 456 Table A-9 1400 W AC-Input Power Supply Power Cords (continued) LocalePower Cord Part Number Length Cordset RatingAC Source Plug Ty p e 120357 120358 120359 120356 120361 120355 120357 203795
A-15 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W DC-Input Power Supply 1400 W DC-Input Power Supply The 1400 W DC-input power supply (PWR-C45-1400DC-P), shown in Figure A-4, is supported in the following Catalyst 4500 E-series switches: •Catalyst 4503-E •Catalyst 4506-E •Catalyst 4507R-E •Catalyst 4510R-E •Catalyst 4507R+E •Catalyst 4510R+E CautionDo not install the 1400 W DC power supply with any other power supply under any circumstances. Doing so can seriously damage your switch.International CAB-AC-2800W-INT= 13.6 ft (4.1 m)16 A, 250 VAC IEC 309 Israel CAB-S132-C19-ISRL 14 ft (4.3 m) 16 A, 250 VAC SI32 UPS 220 VAC CAB-C19-CBN 9 ft (2.74 m) 20 A, 250 VAC IEC-60320-C20 Table A-9 1400 W AC-Input Power Supply Power Cords (continued) LocalePower Cord Part Number Length Cordset RatingAC Source Plug Ty p e 120360 130922 130923
A-16 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W DC-Input Power Supply Figure A-4 1400 W DC-Input Power Supply The 1400W DC-input power supply can be used with the Catalyst 4500 Series AC Power Shelf (PWR-P4502-1PSU). Documentation for the Catalyst 4500 Series AC Power Shelf is located at this url: http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/configuration/notes/ 78_15068.html 1400 W DC-Input Power Supply Specifications Ta b l e A - 1 0 lists the specifications for the 1400 W DC-input power supply. 231377 Table A-10 1400 W DC-Input Power Supply Specifications Item Specification DC-input voltage –48 to –60 VDC (data only) –48 to –56 VDC (inline devices) DC-input current 31 A @ –60 VDC (data only) 180 A maximum @ –48 VDC input (data and inline devices) The input power is configurable in the CLI. The Cisco IOS command is power dc input. Configure the switch software to match the requirements of your switch. Power supply output capacity •Data –12 VDC @120 A, –3.3 VDC @ 10 A –140 A total maximum (35 A maximum each per 5 channels) @–48 to –60 VDC input (inline devices) •1367 W+ 40 W redundant mode (data) 2267 W maximum in combined mode (data) •7500 W maximum each in redundant mode (PoE) 7280 W maximum in combined mode (PoE) DC-input terminal block Accepts 10 to 12 AWG size copper wire. The actual size of the wire needed is determined by the installer or the local electrician. Terminal block material is rated at 150°C
A-17 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W DC-Input Power Supply Output holdup time 4 ms Heat dissipation 159 BTUs/hr (data) 2905 BTUs/hr (data and voice) Table A-10 1400 W DC-Input Power Supply Specifications (continued) Item Specification
A-18 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W DC-Input Power Supply Ta b l e A - 1 1 list the 1400 W DC-input power supply LEDs and their meanings. Ta b l e A - 1 2 lists the chassis specific power usage numbers for the 1400 W DC-input power supply. Table A-11 1400 W DC-Input Power Supply LEDs LED Meaning INPUT OK •Green—Source DC voltage is OK. (Input voltage is –40.5 VDC or greater.) •Off—Source DC voltage falls below –-33 VDC, is not present, or the power supply is turned off. FAN OK •Green—Power supply fan is operating properly. •Off—Power supply fan failure is detected. OUTPUT FAIL •Red—Problem with one or more of the DC-output voltages of the power supply is detected. •Off—DC-output voltage with acceptable margins. In-line PWR •Green—–48 VDC passthrough output voltage is enabled and is greater than –39 VDC and less than –60 VDC. •Off—Indicates any of the following: –Passthrough breakers are not enabled –DC input is less than –40.5 VDC –One or more –48 VDC outputs is less than –39 VDC •Amber—Passthrough breakers are enabled and input voltage exceeds –60 VDC Table A-12 Chassis-Specific Power Usage Chassis Maximum Draw (W)Maximum Input (W)Current Heat Dissipation (BTUs) Catalyst 4503 specific power usage (data only)475 633 •15.6 A @ –40.5 VDC (min) •8.8A @ –72VDC (max)2160 Catalyst 4506 specific power usage (data only)850 1133 •28 A @ –40.5 VDC (min) •15.8 A @ –72 VDC (max)3515 Catalyst 4507R-E specific power usage (data only)1080 1440 •35.6 A @ –40.5 VDC (min) •20 A @ –72 VDC (max)4910
A-19 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W Triple-Input DC-Input Power Supply 1400 W Triple-Input DC-Input Power Supply The 1400 W triple-input DC-input power supply (PWR-C45-1400DC), shown in Figure A-5, is supported in the following Catalyst 4500 E-series switches. •Catalyst 4503-E •Catalyst 4506-E •Catalyst 4507R-E •Catalyst 4510R-E •Catalyst 4507R+E •Catalyst 4510R+E Figure A-5 1400 W Triple-Input DC-Input Power Supply 1400 W Triple Input DC-Input Power Supply Specifications Ta b l e A - 1 3 lists the specifications for the 1400 W triple input DC-input power supply. 231378 Table A-13 1400 W DC Triple-Input Power Supply Specifications Item Specification DC-input voltage •–48 VDC for nominal –48 V battery backup system (operating range: –40.5 VDC to –56 VDC) •–60 VDC for nominal –60 V battery backup system (operating range: –55 VDC to –72 VDC) DC-input current •42.5 A maximum @ –48 VDC input •Input 1—12.5 A @ –48 to –60 VDC •Input 2—15 A @ –48 to –60 VDC •Input 3—15 A @ –48 to –60 VDC Power supply output capacity •1721 W—42.5 A @ –40.5 VDC (min voltage) •1800 W—25 A @ –72 VDC (max voltage)
A-20 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W Triple-Input DC-Input Power Supply Power supply output •8 A (min) to 115.3 A (max) @ +12 VDC •1.2 A (min) to 12.5 A (max) @ +3.3 VDC •1360 W+ 40 W redundant mode 2450 W maximum in combined mode DC input terminal block Accepts 10 to 12 AWG size copper wire. The actual size of the wire needed is determined by the installer or the local electrician. Terminal block material is rated at 302°F (150°C) Output holdup time 8 ms Maximum kVA rating 11.77 kVA (1400 W load) Max heat dissipation 1269 BTUs/hr Minimum software requirementCisco IOS Release 12.2(25)EW Power over Ethernet Not supported Catalyst 4503-E Specific Power Usage (data only)Two modules minimum required @ –40.5 VDC input One 15 A module minimum required @ –44 VDC input Maximum draw 475 W Maximum input 609 W total / # of modules = W per module Current draw at –40.5 V (min voltage) Current draw at –72 V (max voltage) 15 A total / # of modules = Amperes per module 8.5 A total / # of modules = Amperes per module Max heat dissipation at 609 W 2078 BTUs Catalyst 4506-E Specific Power Usage (data only)Two modules minimum required @ –44 VDC input Three modules minimum required @ –40.5 VDC input Maximum draw (data only) 850 W Maximum input 1076 W total / # of modules = W per module Current draw at –40.5 V (min voltage) Current draw at –72 V (max voltage) 26.6 A total / # of modules = Amperes per module 15 A total / # of modules = Amperes per module Max heat dissipation at 1076 W 3671 BTUs Catalyst 4507R-Specific Power Usage (data only)Three modules minimum required Maximum draw (data only) 1080 W Max input is 1080 W 1367 W total / # of modules = W per module Table A-13 1400 W DC Triple-Input Power Supply Specifications (continued) Item Specification
A-21 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W Triple-Input DC-Input Power Supply Ta b l e A - 1 4 list the 1400 W triple-input DC-input power supply LEDs and their meanings. Ta b l e A - 1 5 lists the 1400 W triple-input DC-input power supply input modes and outputs. Current draw at –40.5 V (min voltage) Current draw at –72 V (max voltage) 33.75 A total / # of modules = Amperes per module 19 A total / # of modules = Amperes per module Max heat dissipation 1367 W4665 BTUs 1. The kVA rating listed for the power supply should be used as the sizing criteria for both UPS outputs as well as standard circuits and transformers to power a switch. Table A-13 1400 W DC Triple-Input Power Supply Specifications (continued) Item Specification Table A-14 1400 W DC Triple-Input DC-Input Power Supply LEDs LED Meaning INPUT OK •Green—Source DC voltage is OK. (Input voltage is –40.5 VDC or greater.) •Off—Source AC voltage falls below –33 VDC, is not present, or the power supply is turned off. FAN OK •Green—Power supply fan is operating properly. •Off—Power supply fan failure is detected. OUTPUT FAIL •Red—Problem with one or more of the DC-output voltages of the power supply is detected. •Off—DC-output voltage with acceptable margins. NoteFor proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. Table A-15 1400 W DC Triple-Input Power Supply Input Modes and Output Input ModeSource DC ConnectionsInput Configuration Maximum Total Output Power 1 1 1 x 12.5 A 386 W @ –40.5 VDC 412 W @ –44.0 VDC 2 2 or 3 1 x 15 A 466 W @ –40.5 VDC 495 W @ –44.0 VDC 3 1, 2 or 3 1 x 12.5 A and 1 x 15 A845 W @ –40.5 VDC 908 W @ –44.0 VDC
A-22 Catalyst 4500 E-Series Switches Installation Guide OL-13972-02 Appendix A Power Supply Specifications 1400 W Triple-Input DC-Input Power Supply Power output also depends on whether two supplies are used, and whether they are in redundant or combined mode. Ta b l e A - 1 6 provides a matrix of possible outputs in combined mode depending on the power provided to the supply.4 2, 3 2 x 15 A 914 W @ –40.5 VDC 990 W @ –44.0 VDC 5 1, 2, 3 1 x 12.5 A and 2 x 15 A1294 W @ –40.5 VDC 1400 W @ –44.0 VDC Table A-15 1400 W DC Triple-Input Power Supply Input Modes and Output (continued) Input ModeSource DC ConnectionsInput Configuration Maximum Total Output Power Table A-16 Maximum Power with Two 1400 W DC Triple-Input Power Supplies in Combined Mode PS2 input 1 PS2 input 2 or 3PS2 input 1 and (2 or 3)PS2 input 2 and 3PS2 input 1 and 2 and 3 PS1 input 1 824 W 907 W 1320 W 1400 W 1700 W PS1 input 2 or 3 907 W 990 W 1400 W 1450 W 1750 W PS1 input 1 and (2 or 3)1320 W 1400 W 1700 W 1750 W 1900 W PS1 input 2 and 31400 W 1450 W 1750 W 1820 W 2130 W PS1 input 1 and 2 and 31700 W 1750 W 1900 W 2130 W 2450 W