Home > Cisco > Ethernet Switch > Cisco 4507re Manual

Cisco 4507re Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Cisco 4507re Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 174
    Add page 111 to Favourites
    image text
    Enable zoom 
    							A-3
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1000 W AC-Input Power Supply
1000 W AC-Input Power Supply Specifications
Ta b l e A - 1 lists the specifications for the 1000 W AC-input power supply.
Table A-1 1000 W AC-Input Power Supply Specifications
Item Specification
AC-input type Autoranging input with power factor correction (PFC)
NotePower factor correction is a standard feature on all Catalyst 4500 
E-series AC-input power supplies. PFC reduces the reactive 
component in the source AC current allowing higher power 
factors (typically 99 percent or better) and lower harmonic 
current components.
AC-input voltage
•Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max)
•High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max)
AC-input current
•12 A @ 120 VAC
•5A @ 240VAC
AC-input frequency 50/60 Hz (nominal) (±3 Hz for full range)
Branch circuit requirement Each chassis power supply should have its own dedicated, fused-branch 
circuit:
•For North America—15 A or 20 A
•For International—Circuits sized to local and national codes
•All Catalyst 4500 E-series AC-input power supplies require 
single-phase source AC.
•All AC power supply inputs are fully isolated.
–Source AC can be out of phase between multiple power supplies 
in the same chassis, which means that PS1 can be operating 
from phase A and PS2 can be operating from phase B.
–For high-line operation, the power supply operates with the hot 
conductor wired to a source AC phase and the neutral conductor 
wired either to ground or to another source AC phase as long as 
the net input voltage is in the range of 170 to 264 VAC.
–Source AC can be out of phase between AC inputs on power 
supplies that are equipped with multiple AC inputs, which 
means that power cord 1 can be plugged into phase A and 
power cord 2 can be plugged into phase B.
    Add page 112 to Favourites
    image text
    Enable zoom 
    							A-4
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1000 W AC-Input Power Supply
Ta b l e A - 2 lists the 1000 W AC-input power supply LEDs and their meanings.
1000 W Power Supply AC Power Cords
Ta b l e A - 3 lists the specifications for the regional AC power cords that are available for the 1000 W 
AC-input power supply.
NoteAll 1000 W power supply AC power cords have an IEC60320/C15 appliance plug at one end. Power supply output 
capacity 1050 W plus 40 W (fan)
Power supply output 83.4 A @ +12 VDC
12.2 A @ +3.3 VDC
Output holdup time 20 ms minimum
Maximum kVA rating 1.32 kVA
Max heat dissipation 943 BTUs/hr
Minimum software 
requirementCisco IOS Release 12.1(12c)EW
Power over Ethernet Not supported
1
1. A Catalyst 4503 with a Catalyst 4500 series Supervisor Engine II-Plus TS and a 1000 W power supply will be able to provide 
158.4 W of Power over Ethernet (PoE) to ports on the supervisor engine. Switching modules in the other slots will not be able 
to provide PoE.
Table A-1 1000 W AC-Input Power Supply Specifications (continued)
Item Specification
Table A-2 1000 W AC-Input Power Supply LEDs
LED Meaning
INPUT OK
•Green—Source AC voltage is OK. (Input voltage is 85 VAC or 
greater.)
•Off—Source AC voltage falls below 70 VAC, is not present, or the 
power supply is turned off.
FAN OK
•Green—Power supply fan is operating properly.
•Off—Power supply fan failure is detected.
OUTPUT FAIL
•Red—Problem with one or more of the DC-output voltages of the 
power supply is detected.
•Off—DC-output voltage with acceptable margins.
    Add page 113 to Favourites
    image text
    Enable zoom 
    							A-5
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1000 W AC-Input Power Supply
Table A-3 1000 W AC Power Supply Power Cords
LocalePower Cord Part 
Number Length Cordset Rating Plug Type
Japan, North 
America CAB-US515-C15-US= 
(was CAB-7KAC=)8.2 ft (2.5 m) 15 A, 125 VAC NEMA 5-15P
Australia, 
New ZealandCAB-AS3112-C15-AU= 
(was CAB-7ACA=)8.2 ft (2.5 m) 15 A, 250 VAC AS/NZS 3112-1993
Europe (except 
Italy)CAB-CEE77-C15-EU= 
(was CAB-7ACE=)8.2 ft (2.5 m) 16 A, 250 VAC CEE 7/7
Italy CAB-C2316-C15-IT= 
(was CAB-7ACI=)8.2 ft (2.5 m) 16 A, 250 VAC 1/3/16 CEI 23-16
United 
KingdomCAB-BS1363-C15-UK= 
(was CAB-7ACU=)8.2 ft (2.5 m) 13 A, 250 VAC BS 1363/A
1
1. Plug contains a 13 A fuse.
Argentina CAB-IR2073-C15-AR= 
(was CAB-7KACR=)8.2 ft (2.5 m) 10 A, 250 VAC IRAM 2073
120354
120356
120357
120358
120359
120356
    Add page 114 to Favourites
    image text
    Enable zoom 
    							A-6
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1300 W AC-Input Power Supply
1300 W AC-Input Power Supply
The 1300 W AC-input power supply (PWR-C45-1300ACV), shown in Figure A-2, is supported in the 
following Catalyst 4500 E-series switches:
•Catalyst 4503-E
•Catalyst 4506-E
•Catalyst 4507R-E
•Catalyst 4507R+E
•Catalyst 4510R-E (the 1300 W AC-input power supply can be installed in the Catalyst 4510R-E 
switch chassis; however power management is required)
•Catalyst 4510R+E (the 1300 W AC-input power supply can be installed in the Catalyst 4510R+E 
switch chassis; however power management is required)
Figure A-2 1300 W AC-Input Power Supply Features
1300 W AC-Input Power Supply Specifications
Ta b l e A - 4 lists the specifications for the 1300 W AC-input power supply. 1AC-input receptacle3Captive installation screws
2Power on/off switch
2313751
2
3
    Add page 115 to Favourites
    image text
    Enable zoom 
    							A-7
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1300 W AC-Input Power Supply
Table A-4 1300 W AC-Input Power Supply Specifications
Item Specification
AC-input type Autoranging input with power factor corrector
NotePower factor correction is a standard feature on all Catalyst 4500 
E-series AC-input power supplies. PFC reduces the reactive 
component in the source AC current allowing higher power 
factors (typically 99 percent or better) and lower harmonic 
current components.
AC-input voltage
•Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max)
•High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max)
AC-input current
•16 A @ 100 VAC
•7A @ 240VAC
AC-input frequency 50/60 Hz (nominal) (±3 Hz for full range)
Branch circuit requirement Each chassis power supply should have its own dedicated, fused-branch 
circuit:
•For North America—15 A or 20 A
•For International—Circuits sized to local and national codes
•All Catalyst 4500 E-series AC-input power supplies require 
single-phase source AC.
•All AC power supply inputs are fully isolated.
–Source AC can be out of phase between multiple power supplies 
in the same chassis, which means that PS1 can be operating 
from phase A and PS2 can be operating from phase B.
–For high-line operation, the power supply operates with the hot 
conductor wired to a source AC phase and the neutral conductor 
wired either to ground or to another source AC phase as long as 
the net input voltage is in the range of 170 to 264 VAC.
–Source AC can be out of phase between AC inputs on power 
supplies that are equipped with multiple AC inputs, which 
means that power cord 1 can be plugged into phase A and 
power cord 2 can be plugged into phase B.
Power supply output 
capacity
•1300 W maximum 
•1050 W+ 40 W redundant mode (data)
•1667 W maximum in combined mode (data)
•800 W maximum each in redundant mode (PoE)
•1333 W maximum in combined mode (PoE)
    Add page 116 to Favourites
    image text
    Enable zoom 
    							A-8
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1300 W AC-Input Power Supply
Ta b l e A - 5 lists the 1300 W AC-input power supply LEDs and their meanings.
1300 W Power Supply AC Power Cords
Ta b l e A - 6 lists the specifications for the AC power cords that are available for the 1300 W AC-input 
power supply. The table includes a power plug illustration for each power cord.
NoteAll 1300 W power supply power cords have an IEC60320/C19 appliance plug at one end. Power supply output 
•84.7 A @ 12 V @ (data)
•12.5 A @ 3.3 V (data)
•16.7 A @ –50 V (PoE)
Output holdup time 20 ms minimum 
Maximum kVA rating 1.76 kVA
Max heat dissipation 1568 BTUs/hr
Minimum software 
requirementCisco IOS Release 12.1(12c)EW
Power over Ethernet (PoE) Supported, up to 800 W (211 Cisco phones in combined mode)
Table A-4 1300 W AC-Input Power Supply Specifications (continued)
Item Specification
Table A-5 1300 W AC-Input Power Supply LEDs
LED Meaning
INPUT OK
•Green—Source AC voltage is OK. (Input voltage is 85 VAC or 
greater.)
•Off—Source AC voltage falls below 70 VAC, is not present, or the 
power supply is turned off.
FAN OK
•Green—Power supply fan is operating properly.
•Off—Power supply fan failure is detected.
OUTPUT FAIL
•Red—Problem with one or more of the DC-output voltages of the 
power supply is detected.
•Off—DC-output voltage with acceptable margins.
NoteFor proper operation of the OUTPUT FAIL LED, systems with 
single power supplies must be configured with a minimum of 
one fan tray assembly and one supervisor engine. Systems with 
dual power supplies must have a minimum configuration of one 
fan tray assembly, one supervisor engine, and one additional 
module. Failure to meet these minimum configuration 
requirements can cause a false power supply output fail signal.
    Add page 117 to Favourites
    image text
    Enable zoom 
    							A-9
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1300 W AC-Input Power Supply
Table A-6 1300 W AC-Input Power Supply Power Cords
LocalePower Cord Part 
Number Length Cordset RatingAC Source Plug 
Ty p e
Japan, North 
America CAB-US520-C19-US= 
(was CAB-7513AC=)14 ft (4.3 m) 20 A, 125 VAC NEMA 5-20
Australia, 
New ZealandCAB-A3112-C19-AUS= 
(was CAB-7513ACA=)14 ft (4.3 m) 15 A, 250 VAC SAA/3,
AS/NZZS 3112-1993
Europe (except 
Italy)CAB-CEE77-C19-EU= 
(was CAB-7513ACE=)14 ft (4.3 m) 16 A, 250 VAC CEE 7/7
Italy CAB-C2316-C19-IT= 
(was CAB-7513ACI=)14 ft (4.3 m) 16 A, 250 VAC 1/3/16, CEI 23-16
United 
KingdomCAB-BS1363-C19-UK= 
(was CAB-7513ACU=)14 ft (4.3 m) 13 A, 250 VAC BS 89/13
BS 1363/A
Argentina CAB-IR2073-C19-AR= 
(was CAB-7513ACR=)14 ft (4.3 m) 16 A, 250 VAC IRAM 2073
Japan, North 
America 
(locking)
200–240 VAC 
operationCAB-AC-2800W-TWLK= 13.6 ft 
(4.1 m)16 A, 250 VAC NEMA L6-20
120362
120356
120357
120358
120359
120356
120361
    Add page 118 to Favourites
    image text
    Enable zoom 
    							A-10
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1400 W AC-Input Power Supply
1400 W AC-Input Power Supply
The 1400 W AC-input power supply (PWR-C45-1400AC), shown in Figure A-3, is supported in the 
following Catalyst 4500 E-series switches:
•Catalyst 4503-E
•Catalyst 4506-E
•Catalyst 4507R-E
•Catalyst 4507R+E
•Catalyst 4510R-E
•Catalyst 4510R+E Japan, North 
America 
(nonlocking)
200–240 VAC 
operationCAB-AC-2800W-6-20= 13.2 ft 
(4.0 m)16 A, 250 VAC NEMA 6-20 
non-locking 
Europe CAB-AC-2800W-EU= 13.2 ft 
(4.0 m)16 A, 250 VAC CEE 7/7
South Africa, 
IndiaCAB-BS546-C15-SA= 
(was CAB-7513ACSA)13.6 ft 
(4.1 m)16 A, 250 VAC BS 456 
International CAB-AC-2800W-INT= 13.6 ft 
(4.1 m)16 A, 250 VAC IEC 309
Israeli CAB-S132-C19-ISRL 14 ft (4.3 m) 16 A, 250 VAC SI32
UPS 220V CAB-C19-CBN 9 ft (2.74 m) 20 A, 250 VAC IEC-60320-C20
Table A-6 1300 W AC-Input Power Supply Power Cords (continued)
LocalePower Cord Part 
Number Length Cordset RatingAC Source Plug 
Ty p e
120355
120357
203795
120360
130922
130923
    Add page 119 to Favourites
    image text
    Enable zoom 
    							A-11
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1400 W AC-Input Power Supply
Figure A-3 1400 W AC-Input Power Supply Features
1400 W AC-Input Power Supply Specifications
Ta b l e A - 7 lists the specifications for the 1400 W AC-input power supply. 1AC-input receptacle3Captive installation screws
2Power on/off switch
2313751
2
3
Table A-7 1400 W AC-Input Power Supply Specifications
Item Specification
AC-input type Autoranging input with power factor corrector
NotePower factor correction is a standard feature on all Catalyst 4500 
E-series AC-input power supplies. PFC reduces the reactive 
component in the source AC current allowing higher power 
factors (typically 99 percent or better) and lower harmonic 
current components.
AC-input voltage
•Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max)
•High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max)
AC-input current
•16 A @ 120 VAC 
•7 A @ 240 VAC
AC-input frequency 50/60 Hz (nominal) (±3 Hz for full range)
    Add page 120 to Favourites
    image text
    Enable zoom 
    							A-12
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Appendix A      Power Supply Specifications
  1400 W AC-Input Power Supply
Ta b l e A - 8 list the 1400 W AC-input power supply LEDs and their meanings. Branch circuit requirement Each chassis power supply should have its own dedicated, fused-branch 
circuit: 
•For North America—15 A or 20 A
•For International—Circuits sized to local and national codes
•All Catalyst 4500 E-series AC-input power supplies require 
single-phase source AC.
•All AC power supply inputs are fully isolated.
–Source AC can be out of phase between multiple power supplies 
in the same chassis, which means that PS1 can be operating 
from phase A and PS2 can be operating from phase B.
–For high-line operation, the power supply operates with the hot 
conductor wired to a source AC phase and the neutral conductor 
wired either to ground or to another source AC phase as long as 
the net input voltage is in the range of 170 to 264 VAC.
–Source AC can be out of phase between AC inputs on power 
supplies that are equipped with multiple AC inputs, which 
means that power cord 1 can be plugged into phase A and 
power cord 2 can be plugged into phase B.
Power supply output  2473 W maximum 
1360 W + 40 W redundant mode (data)
Power supply output (AC 
supply)113.4 A @ +12 V 
12.2 A @ +3.3 V (data)
Output holdup time 20 ms minimum 
Max heat dissipation 1048 BTUs/hr
Maximum kVA rating 1.76 kVA
Minimum software 
requirementCisco IOS Release 12.2(18)EW
Power over Ethernet Not supported
1
1. A Catalyst 4503-E with a Catalyst 4500 E-series Supervisor Engine II-Plus TS and a 1400W AC power supply provides 158.4 
W of PoE to ports on the supervisor engine. Switching modules in other slots will not be able to provide PoE.
Table A-7 1400 W AC-Input Power Supply Specifications (continued)
Item Specification
    All Cisco manuals Comments (0)