Christie Projector Mirage WQ-L User Manual

   Serial Communication
Mirage WQ-L User Manual71
020-101372-02 Rev. 1 (10-2014)
Network Operation
Up to 1000 projectors can be linked together in a  chain with the ‘OUT’ port on one connected to the 
‘IN’ port on the next. A controller connected to the ‘IN’ port on the first projector can control them 
all, either by broadcasting messages which have no address and are thus seen by all projectors, or 
by directing messages to specific projector addresses. 
To work with a specific projector in a group, th...

   Serial Communication
Mirage WQ-L User Manual72
020-101372-02 Rev. 1 (10-2014)
Description Of Control Types
Subclasses
• Power Down Controls:  These controls are accessible when  the projector is in Standby power 
mode (such as power off) as well as when powered on.
• Power Up Controls:  These controls are only accessible when the system electronics are fully 
powered (not necessarily lamp on).
Control Groups
• Unsaved Controls:  These controls are not saved to flash. The settings are not maintained...

Mirage WQ-L User Manual73
020-101372-02 Rev. 1 (10-2014)
GPIO Port
This section explains how to use a GPIO link from  the projector to external equipment, such as 
devices for 3D synchronizing. The GPIO port locate d on the input panel provides a flexible method 
of interfacing a wide range of ex ternal I/O devices to the projector. There are seven GPIO pins 
available on the nine pin D-Sub GPIO connector, which are configurable through RS232 commands. 
The other two pins are reserved for ground and...

   GPIO Port
Mirage WQ-L User Manual74
020-101372-02 Rev. 1 (10-2014)
Configure GPIO
The GPIO connector can be configured to automate any number of events using the serial command 
code  GIO. See  GIO–General Purpose Input/Output  on page 6. Each pin is defined as either an input 
or output depending on the desired outcome. Co nfigure the pin as an input if you want the 
projector to respond to something the device does an d as an output if you want the external device 
to respond to an action taken by...

Mirage WQ-L User Manual75
020-101372-02 Rev. 1 (10-2014)
WebUI Menu Tree
Image Settings
Configuration
3D Settings
1. Reserved
2. 3D Mode
3. Dark Interval
4. 3D Sync Input
5. Invert 3D Input
6. 3D Sync Output
7. 3D Stereo Sync Delay
8. 3D Test Pattern
9. Frame Locking
10. Set Frame Delay
11. Actual Frame Delay
12. Main Input
13. Secondary Input
Image Settings
1.
2. Reserved
3. Gamma Settings
3D Settings
*Read-only
Main Menu
1. Reserved
2.
3. Input & Switching
4. Configuration
5. ArrayLOC
6. Status*
7....

   WebUI Menu Tree
Mirage WQ-L User Manual76
020-101372-02 Rev. 1 (10-2014)
Input & Switching
ArrayLOC
*Read-only
Main Menu1. Reserved
2. Image Settings
3.
4. Configuration
5. ArrayLOC
6. Status*
7. Reserved
8. Test Pattern Input & SwitchingInput & Switching
1. Main Input
2. Secondary Input
3. Swap Main & Secondary Inputs
4. Reserved
5.
6. Frame Locking
Secondary Image Settings SIN+MAIN
SIN+SECD
PPS
FLESecondary Image Settings
1.
2. Secondary Test Pattern
Secondary Gamma Settings
Secondary Gamma...

Mirage WQ-L User Manual77
020-101372-02 Rev. 1 (10-2014)
Specifications
Mirage WQ-L   
(P/N: 130-001102-xx)
Image luminous flux 800 ANSI lumens
contrast 10,000:1 dynamic contrast (under LED control)
No mechanical iris required
uniformity 95% bright ness and color uniformity after electronic adjustment
Display 
technology type
Revolutionary solid state projector using  a single TI Darkchip 3™ DMD with a sold 
state illumination engine (no color wheel) and sealed optics
native resolution 2560 x 1600 WQXGA...

   Specifications
Mirage WQ-L User Manual78
020-101372-02 Rev. 1 (10-2014)
Operating 
environment temperature 40 - 95° F (5-40° C)
humidity 20 - 80 % non-condensing
Operating 
orientation portrait and landscape
Accessories standard Line cord optional • User kit (includes manual, IR remote)  • Rugged Motion Platform kit
2 to withstand 5g shock load (purpose-built)
• Ruggedized transit case
• Remote IR sensor 
• Christie AutoCal
™3 
• Christie MotoBlend™ optical blending
3
Enhanced feature sets • Minimum...

United Kingdom
ph: +44  (0) 118 977 8000United Arab Emirates
ph: +971 4 3206688
Spain
ph: + 34 91 633 9990
Singapore
ph: +65 6877-8737
Republic of South Africa
ph: +27 (0)11 510 0094 Korea (Seoul)
ph: +82 2 702 1601 Japan (Tokyo)
ph: 81 3 3599 7481
India
ph: +91 (080) 6708 9999
Germany
ph: +49 2161 664540 France
ph: +33 (0) 1 41 21 44 04 Eastern Europe and
Russian Federation
ph: +36 (0) 1 47 48 100
China (Shanghai)
ph: +86  21 6278 7708 China (Beijing)
ph: +86 10 6561 0240
Brazil
ph: +55 (11) 2548 4753...

For the most current technical documentation, please visit  www.christiedigital.com