Christie Projector Mirage WQ-L User Manual

   Installation
Mirage WQ-L User Manual21
020-101372-02 Rev. 1 (10-2014)
1. Connect a standard CAT5 Ethernet cable between the controller (or Ethernet hub) and the 
Control Network port on the projectors input panel. 
2. From the WebUI, set the IP address in  Configuration > Communications  > Ethernet 
Settings . 
3. From the WebUI, in  Configuration > Communications set network routing to  Separate. 
 
Mixed Network
In a mixed network the controller can communicate with the first projector and the...

   Installation
Mirage WQ-L User Manual22
020-101372-02 Rev. 1 (10-2014)
5. If the controller is connected via an Ethernet cable, set the IP address from the WebUI in 
Configuration  > Communications >  Ethernet Settings. 
6. Set the serial options in  Configuration > Communications . 
7. From the WebUI, select  Configuration > Communications  > Network Routing . 
• To relay commands to all projectors set  Network Routing to All Joined.
• To isolate RS422 communications, select  RS232 and Ethernet...

   Installation
Mirage WQ-L User Manual23
020-101372-02 Rev. 1 (10-2014)
5. Set network routing in  Configuration > Communications  > Network Routing  to RS232 
and RS422 Joined .  
Mixed Serial Network (RS232 and RS422)
RS422 serial communication is better over lo ng distances than RS232 communication. Use the   
RS422 port only if your device has RS422 capab ility. Always read the equipment literature before 
connecting. In the RS422 network the controller ca n communicate with the first projector and...

   Installation
Mirage WQ-L User Manual24
020-101372-02 Rev. 1 (10-2014)
4. Set network routing in  Configuration > Communications  > Network Routing  to RS232 
and RS422 Joined . 
ArrayLOC Network Configuration
Preliminary color setup is managed by ArrayLOC. Ar rayLOC is enabled by default and configured to 
display a reasonably saturated gamut at the maximum brightness that all the projectors in the 
array can support.   
ArrayLOC over Control Network
Use the Control Network for ArrayLOC when you want...

   Installation
Mirage WQ-L User Manual25
020-101372-02 Rev. 1 (10-2014)
 
Adjust Image Geometry and Optical Alignment
Basic Optical Alignment
1. Press  Test on the IR remote to  display a test pattern. 
It is recommended to use the  Edge Blend or Grid test pattern.
2. Perform a quick preliminary focus and (if available) zoom adjustment with the primary lens. Do  not worry about consistency across the image at this  point, just center focus. It is good practice 
to have the zoom adjustment collar and the...

   Installation
Mirage WQ-L User Manual26
020-101372-02 Rev. 1 (10-2014)
3. Hold a piece of paper at the lens surface, adju st offsets as necessary until the image is centered 
within the lens perimeter. A full white field works best for this.
4. If necessary, center the image on the screen.  If the projector is mounted off-center to the 
screen axis, then offset the lens as much as re quired. Aim the projector over slightly towards 
the center of the screen, but use caution, as too much tilt will cause...

   Installation
Mirage WQ-L User Manual27
020-101372-02 Rev. 1 (10-2014)
7. Adjust square 3, by adjusting the appropriate  cap screw. Adjust until the image is in focus with 
minimal flare. 
8. Repeat steps 5 to 7, as required until all square s on the test pattern are equally focused. If the 
boresight is acceptable, continue to step 11. If the boresight does not appear to be converging 
to an acceptable level of image quality or if  the lens will not focus over the correct range of 
throw distances,...

Mirage WQ-L User Manual28
020-101372-02 Rev. 1 (10-2014)
Web UI Overview
Login to WebUI
1. Open your web browser and enter the IP address (in the address bar) assigned to your 
projector. 
2. Select the appropriate language from the  Language drop-down list, located in the upper left-
hand corner. 
3. Enter your user name and password. Both entries are case-sensitive.
4. Click the  Login button. The  Main window appears.
5.
i 
The factory default IP address is 192.168.1.89 . To change the default use the...

   Web UI Overview
Mirage WQ-L User Manual29
020-101372-02 Rev. 1 (10-2014)
Navigate the WebUI
This section describes the controls and switches us ed for projector operation once it is properly 
installed and configured. The projectors can be controlled remotely, typically at a controller such as 
a PC, through a WebUI on an Ethernet Network. If  there are concerns about network security, run 
the WebUI on a local area network only and insta ll a firewall. Users are prompted to log in upon 
start-up. Use...

   Web UI Overview
Mirage WQ-L User Manual30
020-101372-02 Rev. 1 (10-2014)
• When you are finished making your adjustment,  press  Enter to save and return to your 
presentation. Press  Esc to cancel any adjustments.
• Some settings automatically impose a test patte rn or color change as part of making the 
adjustment. Press  Enter to save the adjustment. Press  Esc to cancel any adjustments.
Check Boxes
A condition is present if an adjacent check box contains a check mark.  
To select or clear the...