Christie Projector Mirage WQ-L User Manual

   Operation
Mirage WQ-L User Manual51
020-101372-02 Rev. 1 (10-2014)
Select a Color
From the Color Enable  drop-down select a color while working with color temperature, input levels 
or other setup parameters. 
Select a Light Engine Test Pattern
From this drop-down select 1 of four light module test patterns. Choose from  White, Grey Scale 
16 , Horizontal Ramp , No Test Pattern .
Upgrade Software
The upgrade package is a single file, which comp rises all the firmware and software needed to 
operate...

   Operation
Mirage WQ-L User Manual52
020-101372-02 Rev. 1 (10-2014)
• The Upgrading progress bar indicates the status of the current action.
• The upgrading process takes between 15 and 30 minutes.
10. Click Reboot to re-starts the projector in Normal mode.  If you are unable to see the WebUI after the up grade delete the cache and cookies, and press 
CTRL+F5.       
Warp and Blend Images
The digital image warp and blend functionality comb ines multiple projector images into a single 
image. Use the...

   Operation
Mirage WQ-L User Manual53
020-101372-02 Rev. 1 (10-2014)
When these frames are displayed fast enough and  viewed with special glasses synchronized to the 
left or right changes, the resulting image appe ars to have the same depth and perspective as 
reality.
To display stereoscopic 3D video, you must connect the Mirage WQ-L projector to additional 
hardware such as stereo emitters and glasses. The type of 3D glasses can be active or passive 
depending on the type of stereo controller and...

   Operation
Mirage WQ-L User Manual54
020-101372-02 Rev. 1 (10-2014)
• Emitter for controlling active shutter glasses, or  a qualified device that mounts in front of the 
lens of the projector to process the light from the lens into a passive polarized light for passive 
glasses. Contact your Christie dealer for more information.
Software and Content Requiremen ts for Stereo 3D Applications
• Any 3D computer software that supports 3D stereo on a supported computer(s) with associated 
graphic cards....

   Operation
Mirage WQ-L User Manual55
020-101372-02 Rev. 1 (10-2014)
In response to the 3D Sync Out signal from th e projector (BNC A), the infrared emitter emits a 
signal to the receiver in the active 3D shutter gla sses. This synchronizes the active glasses to open 
and close for the active stereo 3D content. The left /right synchronization signal is connected to BNC 
B on the projector, which is necessary for 3D frame doubled input configurations.
Passive Stereo 3D Configuration 
This diagram shows...

   Operation
Mirage WQ-L User Manual56
020-101372-02 Rev. 1 (10-2014)
For operation with passive glasses, a 3D polarization  filter is placed in front of the lens and is 
synchronized to the projected frames with the  3D Sync Out signal (BNC A). The left/right 
synchronization signal is connected to BNC B on  the projector, which is necessary for 3D frame 
doubled input configurations.
Set Up the Mirage WQ-L to Display 3D Content 
The projector must be installed to correctly display 2D content (optically...

Mirage WQ-L User Manual57
020-101372-02 Rev. 1 (10-2014)
Troubleshooting
• Make sure the projector is plugged in.
• Make sure all cables are connected and not damaged.
• Power down the projector, wait 90 seconds to  allow for cooling, and then power the projector 
back up. Check for a normal power up sequence. 
• Check the projector status for error conditions and correct any issues if possible.  See  System Warnings and Errors  on page 57.
• Check source reliability. Switch sources if possible.
• Use...

   Troubleshooting
Mirage WQ-L User Manual58
020-101372-02 Rev. 1 (10-2014)
Status Display
Projector status is indicated by a single three-color LED adjacent to a two-digit status display. Refer 
to the table below for a description of the variations that indicate operation status. A solid red LED 
indicates a system error and the corresponding error code indicates what the error is. 
Error Codes
If the status display window shows any of the co des in the table below you may need a Christie 
accredited...

   Troubleshooting
Mirage WQ-L User Manual59
020-101372-02 Rev. 1 (10-2014)
Acknowledge and clear the error by pressing  Exit twice. If the error recurs then try resetting the 
projector by powering Off and On again. Contact th e dealer if the problem persists or if you see a 
code not listed in the table below. 
Error Code
(7-segment 
display)Description
Light Engine
LE Light engine error Engine error (typically during power-up)
Link
LI Link downCommunication link status (internal communication error)...

   Troubleshooting
Mirage WQ-L User Manual60
020-101372-02 Rev. 1 (10-2014)
20 Power supply fan
21 SAM drive fan
22 Intake fan
23 QD fan
24 Red IR fan
25 Green fan
26 Blue Green fan 1
27 Blue Green fan 2
Miscellaneous
ES Emergency stop due to a thermal overtemp (h olds for about 30 seconds and then reverts 
back to standby --y)
Error Code
(7-segment 
display)Description