Christie Projector Mirage WQ-L User Manual

   Operation
Mirage WQ-L User Manual41
020-101372-02 Rev. 1 (10-2014)
1. From the Main menu, select  ArrayLOC > Bright/ColorLOC  Configuration to access and 
work with the capabilities of the projectors in the array.
2. Set the  Minimum Brightness  value (as a percentage of the target brightness). This setting 
indicates the minimum brightness that the array targets, and the threshold for alerts from 
projectors that cannot achieve the minimum. 
3. Set the  Minimum Gamut  value (as a percentage of the...

   Operation
Mirage WQ-L User Manual42
020-101372-02 Rev. 1 (10-2014)
Use this menu on the master projector to configure the target color space settings. This is the 
recommended way to control the color space for the projector and array
. The settings apply to the 
projectors in the same ArrayLOC group. These  settings are enabled on master projectors only. 
1. From the Main menu, select  ArrayLOC > Array Color Target .
2. From the  Target Color Space drop-down list, select a user-defined color space....

   Operation
Mirage WQ-L User Manual43
020-101372-02 Rev. 1 (10-2014)
7. If the array appears matched across all projectors for color and brightness, color setup is 
complete. 
If further adjustment is required, see  Fine-tune Whites, White Brightness, or Primary Colors  
on page 43.
Fine-tune Whites, White Brightness, or Primary Colors
The Projector Color Adjustment menu lets you fine-tune color or brightness for individual projectors 
to accommodate any projector-specific optical elem ents (for example...

   Operation
Mirage WQ-L User Manual44
020-101372-02 Rev. 1 (10-2014)
2. From the  ArrayLOC Network  drop-down list select from  ArrayLOC Network or Control 
Network . 
3. Assign an  ArrayLOC Group  to the array. Only projectors in the same ArrayLOC group 
automatically achieve a common gamut and brightness.
4. Use the Synchronized keys, Test  Pattern, Color Enable option to set the projector to listen 
for remote keystrokes through the ArrayLOC network and the master projector. All 
synchronized...

   Operation
Mirage WQ-L User Manual45
020-101372-02 Rev. 1 (10-2014)
Once you have made an adjustment, re-measure  and refer to the guide for the next adjustment. 
Repeat until the desired color accuracy is achieved. 
1 some corrections require bo th red and green adjustments.2 alternative: decrease blue (-B) instead of increasing red and green.3 alternative: increase blue  (+B) and increase green (+G) instead  of decreasing red and increasing green.
Image Settings
Adjust Gamma Settings
To access the...

   Operation
Mirage WQ-L User Manual46
020-101372-02 Rev. 1 (10-2014)
Select Gamma
Select the base gamma table 
for a given source. Select 
from one of the standard 
tables, a custom gamma 
function, or select an 
arbitrary gamma table that 
has been downloaded to the 
projector. A separate PC 
utility is needed to do this. 
The 2.22 curve is a power 
curve typically used to 
encode graphics and video sources. The  Standard curve (auto setup default) is a modified 2.22 
curve with a small linear section...

   Operation
Mirage WQ-L User Manual47
020-101372-02 Rev. 1 (10-2014)
Output Options
Change Screen Image Orientation
1. From the Main menu, select  Configuration > Output Options .
2. From the  Screen Image Orientation drop-down select from front, rear, front inverted, and 
rear inverted.
Control Frame Locking
Use frame locking to select how the projector controls the output frame timing based on the input 
signal. 
1. From the Main menu, select  Configuration > Output Options .
2. From the Frame Locking...

   Operation
Mirage WQ-L User Manual48
020-101372-02 Rev. 1 (10-2014)
automatically goes into Standby mode. The presence  of any activity within this combined interval 
cancels auto shutdown and returns the projector to normal operation. 
Turn Off Image After (min)
This sets the activation interval (in minutes) for auto shutdown. If all activity (input signals, Web or 
Serial port activity key presses) is lost for this  length of time, and auto shutdown is enabled, an 
auto shutdown cycle begins.
Enter...

   Operation
Mirage WQ-L User Manual49
020-101372-02 Rev. 1 (10-2014)
Serial Flow Control : Determines whether software flow control or no flow control is used when 
transmitting and receiving data on the serial port. 
Serial Mode : Select the serial data mode. The mode in cludes the number of bits, the parity and 
the number of stop bits.
Serial Protocol : Select the protocol used on the serial communications port.
Projector Address
Enter a number up to three-digits in length (such as “001”) to assign...

   Operation
Mirage WQ-L User Manual50
020-101372-02 Rev. 1 (10-2014)
Subnet Mask : Subnet Mask determines the subnet ma sk for the IP address and must be set 
manually. 
Gateway : This is the IP address of the gateway used  to reach any non-local IP addresses; it must 
be set manually.
Host Name : Set the hostname for the device.
Domain Name : Set the domain for the device.
MAC Address : Displays the MAC address of the projector (read-only).
Broadcast Keys
Use Broadcast Keys to relay all key presses...