Christie Projector Mirage S+/HD/WU User Manual

 Section 3: Operation 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  3-31 020-100001-07 Rev. 1 (11-2009) 
 
Figure 3.7. Adjusting Input Levels Using the Peak Detector 
(RED EXAMPLE SHOWN) 
Advanced Image Settings 
— 
SUBMENU
 
Use the Advanced Image Settings 
submenu to make the adjustments 
necessary for lesser-used but more 
specialized applications on your 
projector. 
NOTE: 3D Source option is only 
available for Mirage HD. 
 
GAMMA TABLE: This control applies 
a default...

Section 3: Operation  
3-32  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
NOTES: 1) If no user curves have been defined and downloaded to projector 
memory, only the 2.2 default gamma curve is available here – adjust as desired using 
gamma in the main Image Settings menu. 2) Some graphic material will look best with 
the video setting while some video material is best with the graphic setting. 
SELECT COLOR ADJUSTMENT: In “Select Color...

 Section 3: Operation 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  3-33 020-100001-07 Rev. 1 (11-2009) 
OPTICAL APERTURE - The optical aperture inside the projector controls the diameter 
of the light beam passing through the system. With a fully open aperture (slide bar 
default of “0”), the maximum amount of light passes through for maximum brightness 
in your images. Increase the slide bar setting to reduce the aperture diameter and 
maximize contrast ratio instead....

Section 3: Operation  
3-34  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
FRAME DELAY — Set the number of lines delayed between the input signal and its 
appearance on screen, keeping in mind that projector processing always adds one 
frame of delay to the frame delay setting. For applications such as simulation, where 
the feeling of “real time” image response is a priority, a minimum setting is usually 
preferable. For projectors capable of 3D...

 Section 3: Operation 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  3-35 020-100001-07 Rev. 1 (11-2009) 
3D STEREO SYNC DELAY — Set when the L/R frames begin, defining the best 
reference point for synchronizing the display with your glasses. Proper adjustment of 
this delay should eliminate cross talk and odd colors caused by timing differences 
between the glasses and the projected display. Use this slide bar only if the Mirage 3D 
Stereo Sync Cable is connected between the...

Section 3: Operation  
3-36  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
DARK INTERVAL — Adjust Dark Interval to artificially increase the amount of dark 
time between displayed frames for stereographic 3D images. Higher settings provide 
more time for shutters in 3D glasses to open/close, ensuring that each eye sees the full 
display intended for it. Symptoms of cross talk and/or color artifacts can indicate need 
for adjustment. The Dark...

 Section 3: Operation 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  3-37 020-100001-07 Rev. 1 (11-2009) 
3D STEREO SYNC DELAY — This value is set when the L/R frames begin and by 
default, is automatically calculated based on signal timing; it defines the best 
reference point for synchronizing the display with your glasses. Proper adjustment of 
this delay should eliminate cross talk and odd colors caused by timing differences 
between the glasses and the projected display....

Section 3: Operation  
3-38  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
ACCUFRAME – Increasing the AccuFrame value will reduce the artifacts related to fast 
motion in simulation content. Symptoms of blurry objects or loss of apparent detail 
may indicate a need for this value to be adjusted.  
 
NOTE: If increasing AccuFrame does not improve image quality, reduce the value to 
0. Increasing AccuFrame may increase ‘flicker’ of the display and...

 Section 3: Operation 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  3-39 020-100001-07 Rev. 1 (11-2009) 
3D SOURCE — When using a Mirage projector with HD or WUXGA resolution, a 
checkbox option called 3D Source will be added to the bottom of the Advanced Image 
Settings menu. This checkbox must be set by the user for all new 3D sources, and 
cleared for all new non-3D sources (default setting is checked).  Once set, this value 
will be maintained for that source for all future...

Section 3: Operation  
3-40  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
Menu Preferences — SUBMENU 
Adjust the appearance, content 
and/or location of on-screen 
menus and messages. 
LARGE MENU FONT — Enter a 
checkmark to enlarge menus and 
their text. You may have to adjust 
“Menu Location” to accommodate 
the increased menu area. 
MENU LOCATION — Use the pull-down list to choose a pre-defined default or 
customized location for the display of...