Christie Projector Mirage S+/HD/WU User Manual

 Section 4: Maintenance 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  4-5 020-100001-07 Rev. 1 (11-2009) 
 
The IR Remote Keypad uses two AA size, 1.5V batteries (preferably alkaline). To 
install new batteries:  
1) Open the battery 
compartment at the backside 
of the keypad by placing your 
thumb in the oval depression 
and sliding the cover out about 
½ inch. See Figure 4.1. 
Remove the old batteries and 
properly discard. Wait a 
minute or two.  
2) Place the new batteries...

Section 4: Maintenance  
4-6  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
Table 4.2. Lamp/Filter Replacement Kits 
Projector ModelModel NumberLamp Type (Watts) Lamp/Filter Kit Required
Mirage S+3K 38-DSP102-xx 
500W  
 
 
 
 
003-120118-01 
Mirage HD3 104-012101-xx 
Christie HD3K 104-025101-xx 
Mirage WU3 104-060107-xx 
Christie HD2Kc 104-026101-xx 
Matrix S+2K 38-DSP102-xx 
Matrix HD2 104-023101-xx 
Matrix WU2 104-058104-xx 
DLV1400-DX...

 Section 4: Maintenance 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  4-7 020-100001-07 Rev. 1 (11-2009) 
 
1. TURN THE LAMP OFF 
Press 
 (power) to turn the lamp off. Allow the cooling fans to stop 
automatically (within approximately five minutes) before proceeding with Step 2. 
This wait period is also required to allow the lamp to sufficiently cool before 
handling. 
2. UNPLUG THE PROJECTOR 
When the cooling fans have stopped, turn the projector’s main switch off, and...

Section 4: Maintenance  
4-8  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
 
Figure 4.3. Release the Lamp Lock 
5. REMOVE THE LAMP MODULE 
Firmly grasp the lamp by its housing only and pull it straight out (lamp slides 
along guides) until it is free. See Figure 4.4. Discard the lamp using safe 
disposal/recycling practices.
 
 
 
 
6. INSERT THE NEW LAMP MODULE 
Align the new lamp with the top and bottom guides on the left side of the lamp...

 Section 4: Maintenance 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  4-9 020-100001-07 Rev. 1 (11-2009) 
 
       Figure 4.5. Insert New Lamp Module
 
 
 WARNING  
Improper installation could cause a serious 
meltdown inside the projector. 
7. LOCK IN THE NEW LAMP MODULE 
Pull out and turn the lamp lock lever (turned up in Step 4) ¼ turn clockwise to 
“lock” the lamp in place.  
 
NOTE: If you can’t turn the lamp lock into position, it is likely the lamp is not 
fully inserted....

Section 4: Maintenance  
4-10  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
1.
2.
3.
4.
5.
6.
7.
8.Lamp Hours
Lamp S/N
Lamp Message
Lamp Limit
Lamp Mode
Power
Intensity
Optical Aperture
Lamp History
Change Lamp
Lamp
0
?
1000
Power
500
0
3
Lamp S/N
S/N
5679
1234Hours
1001
0
Lamp HistoryNew serial# entry
automatically updates
Lamp History...
...and resets Lamp
Hour
s to “0” 
 
                  
IMPORTANT: If you neglect to enter a serial number,...

 Section 4: Maintenance 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  4-11 020-100001-07 Rev. 1 (11-2009) 
3. REPLACE FILTERS 
Pull the old filters out of the projector and discard. Do not reuse filters. Insert the 
new filters with the wired side in. See Figure 4.7. 
 
Figure 4.9. Insert New Filters
 
 
4. REPLACE ACCESS PANELS 
Replace the two (2) filter access panels and tighten the screws loosened in step 1. 
 
A variety of lenses can accommodate different throw distances...

Section 4: Maintenance  
4-12  Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  020-100001-07 Rev. 1 (11-2009) 
 
Figure 4.10. Lens Assembly 
Install the lens cap and press the lens release button 
See Figure 4.11. 
 
Figure 4.11. Depressing Lens Release 
Rotate the lens  
Rotate the lens counter-clockwise until 
the tabs are free from the lens retainer 
ring, see A in Figure 4.12. 
NOTE: The connector slide assembly 
allows the connector to move as the 
lens is rotated. 
Pull lens...

 Section 4: Maintenance 
Mirage S+/HD/WU, Matrix S+/HD/WU, Christie HD/DS+/DW, DLV User Manual  4-13 020-100001-07 Rev. 1 (11-2009) 
 Electrical connector: Line up male connector on the lens with the female 
connector on the connector slide assembly. 
 Insert lens: Align the tabs on the lens 
plate lock with the slots in the lens 
retainer ring. Push the lens in until the 
tabs touch the back of the retainer ring. 
 Rotate the lens: 
To ensure the lens is 
secured in the lens mount, turn it 
clockwise...