Christie Projector Mirage 4K25 User Manual

   Installation and Setup
Mirage 4K25 User Manual31
020-101361-02 Rev. 1 (01-2015)
Portrait mode
1. Orient the projector in the frame with th e lamp door facing downward (as shown).
The maximum tilt angle is ±15 degrees.
2. Set up the customer-supplied mounting frame.  The mounting frame must be designed to acco mmodate the weight and mounting provisions of 
the projector.
3. Remove the projector feet.
4. Attach the projector to the mounting frame using the four M12 holes (normally used for  projector...

   Installation and Setup
Mirage 4K25 User Manual32
020-101361-02 Rev. 1 (01-2015)
left/right (L/R) changes, the resulting image appe ars with the same depth and perspective sense in 
the real world.
3D requirements
Stereo 3D applications require a stereo 3D-capable source, special hardware and software setups, 
and the projector’s 3D Settings menu option to control the projector’s processing, synchronization, 
and displaying of the stereoscopic 3D source material.
Hardware requirements
Note the...

   Installation and Setup
Mirage 4K25 User Manual33
020-101361-02 Rev. 1 (01-2015)
Active stereo 3D configuration
The following diagram shows the typical hardware  configuration for active stereo 3D systems:
i
In response to the 3D Sync Out signal from the projector, the IR emitter emits an infrared signal to a 
receiver in the active 3D shutter glasses. This synchronizes the active glasses to alternatively open 
and close for the active stereo 3D applications. 

   Installation and Setup
Mirage 4K25 User Manual34
020-101361-02 Rev. 1 (01-2015)
Passive stereo 3D configuration
The following diagram shows the typical hardware  configuration for passive stereo 3D systems:
3D system timing
Consult the documentation for your glasses or polari zation filter and keep their specifications in 
mind when configuring the projec tor for 3D operation. The projected video must be optimized for 
the glasses’ shutter speed or polarization filter  performance to prevent obvious...

   Installation and Setup
Mirage 4K25 User Manual35
020-101361-02 Rev. 1 (01-2015)
3D input video configurations
The stereo 3D input video stream may be supplied  from the video server to the projector in two 
configurations: Direct-Input 3D or Dual-Input 3D.
Set up a single Mirage 4K to display 3D content
The projector must be installed co rrectly to display 2D content (lamp installed, optically aligned, 
focused, and so on) before completing the following steps to display the 3D content:
1. Confirm the...

   Installation and Setup
Mirage 4K25 User Manual36
020-101361-02 Rev. 1 (01-2015)
Configure the projector for the 3D source
1. Select the channel (from the Home tab) best suited for the 3D source.
2. To select the correct EDID timing, tap  Main > Configuration  > EDID Timing Select  and 
select the required EDID timing.
3. Connect all the required cables betw een the 3D source and the projector.
4. Configure your 3D source.
    
    

Mirage 4K25 User Manual37
020-101361-02 Rev. 1 (01-2015)
Connect Devices
This section provides information and procedures  for connecting external devices to the projector.
Communication and input ports are located on the projector side input panel, accessed by removing 
the input panel cover. When connecting devices, you can route cables through the opening in the 
frame to the side input panel or directly to the video option cards and MCPU. The image below 
shows the video option card slot numbers and...

   Connect Devices
Mirage 4K25 User Manual38
020-101361-02 Rev. 1 (01-2015)
Four-Port: DDIC card
The following table shows the video quadrant mappings for the DDIC Four-Port input configuration:
Two-Port: TDPIC card
Two-Port: DDIC card
Slot 2 1-In Top right3
Slot 2 2-In Bottom right4
Four-Port Input Configuration—Two Cards (2) Quadrants Columns
Slot 3 1-In Top left1 (left most)
Slot 3 2-In Bottom left2
Slot 4 1-In Top right3
Slot 4 2-In Bottom right4
Four-Port Input Configuration—Four Cards...

   Connect Devices
Mirage 4K25 User Manual39
020-101361-02 Rev. 1 (01-2015)
Connect a video source using DisplayPort
The Twin DisplayPort Input card (TDPIC) accepts di gital video data from the DisplayPort sources. 
The input configurations listed below are supported.
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see  Two-
Port: TDPIC card  on page 38 and For limitations of one card use for One-Port Dual-Input 3D, see 
Mirage signal connectivity  on page 84....

   Connect Devices
Mirage 4K25 User Manual40
020-101361-02 Rev. 1 (01-2015)
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see  Two-
Port: TDPIC card  on page 38 and For limitations of one card use for One-Port Dual-Input 3D, see 
Mirage signal connectivity  on page 84.
Connect a video source using HDMI
The Twin HDMI Input card (THIC) accepts digital video data from HDMI sources. The input 
configurations listed below are supported.
Input...