Christie Projector Mirage 4K25 User Manual

Mirage 4K25 User Manual21
020-101361-02 Rev. 1 (01-2015)
Installation and Setup
This section explains how to install, co nnect, and optimize the projector display.
Site requirements
To safely install and operate the projector, the inst allation location must have restricted access for 
authorized personal only and me et these minimum requirements.
Physical operating environment
• Maximum Ambient Temperature (operating) 35°C (95°F)
• Minimum Ambient Temperature (operating) 10°C (50°F)
External exhaust...

   Installation and Setup
Mirage 4K25 User Manual22
020-101361-02 Rev. 1 (01-2015)
• Christie approved protective safety clothing if working with the lamp
• Lens cleaning tissue and solution 

   Installation and Setup
Mirage 4K25 User Manual23
020-101361-02 Rev. 1 (01-2015)
Projector components
IDItemDescription
A Touch panel controller (TPC) A touch-sensitive scre en used to control and monitor operation. For 
information about TPC controls and settings, see  Menus on page 58.
B LED status indicators LED color and blinking rates (l ocated in both back corners of the projector) 
provide information about the status of  the projector. For information about 
projector states and status, see...

   Installation and Setup
Mirage 4K25 User Manual24
020-101361-02 Rev. 1 (01-2015)
Position the projector
1. Position the projector at an appropriate th row distance (projector-to-screen distance) and 
vertical position. Ideally, center the projector  with the screen. If space is limited, aim the 
projector slightly off-center. This increases side keystoning, but reduces the horizontal lens 
offset required.
2. If using an optional rack stand (P/N: 108-282101-02), assemble the rack stand using the...

   Installation and Setup
Mirage 4K25 User Manual25
020-101361-02 Rev. 1 (01-2015)
Connect to AC power
1. On the bottom of the projector in the front lamp-side corner, loosen the two screws and slide 
the access panel to expose the terminal block.
2. Remove four screws securing the knockout plate to the bottom right corner of the front bezel.  Remove the knockout plate. The AC supply is routed to the terminal block through an 
appropriate strain relief mounted on this knockout plate.
Failure to comply...

   Installation and Setup
Mirage 4K25 User Manual26
020-101361-02 Rev. 1 (01-2015)
3. Connect to the terminal block. 
• If connecting to permanent power, connect the AC power source to the terminal block, beginning with the ground 
lead. 
• If connecting to a pluggable type-B cable, connect the cable  to the terminal block, beginning with the ground lead. 
• Use an appropriately sized strain relief connector with the knockout plate provided to  ensure adequate environmental sealing an d to prevent the...

   Installation and Setup
Mirage 4K25 User Manual27
020-101361-02 Rev. 1 (01-2015)
Adjust the projector tilt and level
Adjust the projector tilt to fill the maximum amount  of screen while minimizing keystone. Lens offset 
can be used to center the image in the center of the screen..
1. Secure a safety lifting strap ra ted to handle the projector weight at the rear of the projector.
2. Hoist up the projector.
3. To adjust the vertical or horizontal position of  the projector, extend or retract the...

   Installation and Setup
Mirage 4K25 User Manual28
020-101361-02 Rev. 1 (01-2015)
Install the touch panel controller
1. Loosen the mounting arm just enough for the end to fit over the ball joint located on the rear 
panel of the projector.
The touch panel controller (TPC) becomes loose from the mounting arm when the mounting 
arm lock is loosened.
2. Tighten the mounting arm lock until it fits tightly on the joint. The TPC safety strap comes installed on the projector ball point.
3. Connect the cable...

   Installation and Setup
Mirage 4K25 User Manual29
020-101361-02 Rev. 1 (01-2015)
Use this formula to determine the CFM value for the projector: 
Add an extractor or a booster if there is insuffic ient airflow. Do not mount the extractor on the 
projector as this may introduce some vibration into the image.
Remove the projector shroud
The lens side shroud must be removed to gain access to the lens. The other shroud must be 
removed when connecting the AC power cord into the front face of the projector....

   Installation and Setup
Mirage 4K25 User Manual30
020-101361-02 Rev. 1 (01-2015)
3. Place the shroud covers on a clean surface to prevent scratches.
Set up the lens
1. Remove the projector shroud. 
2. Make sure the lens locking lever is in the up position.
3. If attached, remove the rear lens cap from the lens.
4. Slide the lens into the lens mount, aligning all connections. 
5. Secure the lens with the lens locking lever (down position).
6. Calibrate the lens motors. 
For more details, see  Work with...