Christie Projector Mirage 4K25 User Manual

   Connect Devices
Mirage 4K25 User Manual41
020-101361-02 Rev. 1 (01-2015)
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see  Two-
Port: TDPIC card  on page 38 and For limitations of one card use for One-Port Dual-Input 3D, see 
Mirage signal connectivity  on page 84.
Connect a video source using DVI
The Dual Link DVI Input card (DDIC) accepts digi tal video data from DVI sources. It does not 
support incoming analog signals. The inpu t configurations listed...

   Connect Devices
Mirage 4K25 User Manual42
020-101361-02 Rev. 1 (01-2015)
1. On the TPC, select  Input > Channel.
2. Scroll the list of channels until you find the channel that best matches your configuration.
3. Tap the channel. An image appears on the screen. If an image does  not appear on the screen, repeat steps 1 to 
3, selecting a different channel.
Connect devices to the 3D Sync ports
The 3D Sync Input and Output ports located on  the MCPU faceplate provide a convenient method 
for interfacing...

   Connect Devices
Mirage 4K25 User Manual43
020-101361-02 Rev. 1 (01-2015)
Set up the ethernet
Ethernet is setup to obtain an IP address automa tically if a DHCP server is on the network. To 
modify IP settings, or manually enter an address.
1. On the touch panel controller, tap  Menu > Configuration  > Ethernet Settings  > Modify 
IP Settings .
2. Set the network information for the projector: • To obtain information automatically from the network, tap  Automatic.
• To manually enter the network...

Mirage 4K25 User Manual44
020-101361-02 Rev. 1 (01-2015)
Adjust the Image
This section provides information and proc edures for adjusting the projector image.
Select screen image orientation
The projector supports front projection, rear pr ojection, front projection inverted, and rear 
projection inverted.
1. On the touch panel controller, tap  Menu > Configuration  > Screen Image Orientation .
2. Select the required orientation from the list.
Maximize light output
To ensure optimal operation, use...

   Adjust the Image
Mirage 4K25 User Manual45
020-101361-02 Rev. 1 (01-2015)
Adjust offset
Project an image with the primary lens. Always adjust offset before adjusting boresight.
Select a framing test pattern and then adjust the vertical (A) and horizontal (B) offsets to display a 
square image on the screen, with minimal projector aiming error.  
Adjust horizontal boresight
The purpose of boresight adjustment is to balance the tilt of the lens mount to compensate for screen-to-
projector tilt.
i
For...

   Adjust the Image
Mirage 4K25 User Manual46
020-101361-02 Rev. 1 (01-2015)
1. Loosen the lens mount stabilization screw (D).
2. Loosen the horizontal lock screw (A).
3. Extend the lens focus (B) completely.
4. Adjust the  Focus using the focus knob to retract the lens. Watch the image at the left edge of 
the screen until it comes into focus. If the entire screen is in focus, proceed to step 7.
5. Continue retracting the lens.
a. If the right side of the image comes into fo cus before the lens is...

   Adjust the Image
Mirage 4K25 User Manual47
020-101361-02 Rev. 1 (01-2015)
2. Loosen the lens mount stabilization screw (D).
3. Loosen the vertical lock screw (A).
4. Extend the lens focus (B) completely.
5. Adjust the  Focus knob to retract the lens. Watch the imag e at the top edge of the screen until 
it comes into focus. If the entire screen is in focus, proceed to step 8.
6. Continue retracting the lens.
a. If the bottom edge of the image comes into fo cus before the lens is completely retracted,...

   Adjust the Image
Mirage 4K25 User Manual48
020-101361-02 Rev. 1 (01-2015)
Lock the lens offsets
The lens locking feature reduces image vibration. Fo r most applications lens locking is not necessary.
1. Use the touch panel controller (TPC) or manually adjust the lens offsets to the required position.
2. Unpack and install the three lens offset locking screws.
3. Tighten each locking screw until each screw contacts the lens offset collar.
4. With equal pressure, tighten each locking screw against the...

   Adjust the Image
Mirage 4K25 User Manual49
020-101361-02 Rev. 1 (01-2015)
Adjust DMD convergence
A convergence problem occurs when one or more  projected colors (red, green, blue) appears 
misaligned when examined with a convergence te st pattern. Normally, the three colors should 
overlap precisely to form pure white lines throug hout the image and one or more poorly converged 
individual colors may appear adjacent to some or all of the lines. 
Contact your Christie accredited service technician to...

   Adjust the Image
Mirage 4K25 User Manual50
020-101361-02 Rev. 1 (01-2015)
Adjust color by precise chromaticity values
1. On the touch panel controller, tap  Menu > Configuration  > Color Correction  > Select 
Color Adjustment .
2. From the list, select Custom .
3. Tap  Color Adjustments by X,Y .
4. Adjust the precise hues of each primary color component.
Adjust color by saturation
1. On the touch panel controller, tap  Menu > Configuration  > Color Correction  > Select 
Color Adjustment .
2. From the...