Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-27020-100707-01  Rev. 1   (10-2011)
4.If necessary, center the image on the screen: If the projector is mounted off center to the screen axis, 
then offset the lens as much as required. Aim the projector over slightly towards the center of the screen, 
but use caution when doing so, as too much tilt will cause excessive keystone distortion. Lens offset will 
not. 
5.Re-check side-to-side leveling: With the framing pattern on...

2-28J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
3. If boresight is required, refer to Figure 2-34 Cross-Hair Pattern to understand how the adjustment screws 
on the lens mount affect the corresponding cross-hairs on the test pattern. 
NOTE: The capscrew, (Figure 2-
35) may be under a plastic cap, remove and retain before adjusting.
4. Use a 5mm Allen™ key to loosen the 3 locking setscrews on the lens mount, see Figure 2-35 Screw 
Locations,...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-29020-100707-01  Rev. 1   (10-2011)
11. Lock the setscrews, and re-check the boresight quality. Tighten the setscrew enough to ensure they will not 
shift.
FIGURE 2-36 
2.3.6 Powering Down
The projector can be powered down by using one 
of the following methods:
Remote Keypad/Built-In Keypad
• Press and hold P
OWER
OR
• Press P
OWER twice
OR
• Press P
OWER once, then immediately press the 
DOWN key. 
NOTE: For Step 2 and 3, if...

2-30J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
2.3.7 Connecting Communications
Remote Keypads
To control the projector, direct the projector IR remote towards the display screen or the projector IR sensors. 
Alternatively, connect a wired (tethered) version of the remote to the XLR connector labeled as 
WIRED KEYPAD on the 
projector input panel. 
NOTE: The response to a wired keypad must also be enabled in the Communications menu—see...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-31020-100707-01  Rev. 1   (10-2011)
Ethernet Communications
Refer to Section 3 Operation for further information about setting up and using a projector connected via 
Ethernet, and the Serial Command document provided in the Dealer Section of the Christie Website, PN 020-
100224-XX.
Connecting Multiple Projectors
RS-232 NETWORK: To connect multiple projectors in a network with serial communication:
1. Connect the controlling...

2-32J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
MIXED NETWORK: To control multiple projectors with a computer/controller having an RS-422 interface:
1. Set them all to the same baud rate as your RS-422 controller. 
NOTE: You must enable this combination of 
RS-422 and RS-232 in the Communications menu. Set the “Network Routing” option to “RS-232 and 
RS-422 Joined”, see Section 4 Web User Interface.
2. Chain the projectors together by...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-33020-100707-01  Rev. 1   (10-2011)
FIGURE 2-42 ETHERNET NETWORK SETUP
SETTING THE PROJECTOR IP ADDRESS, SUBNET MASK AND GATEWAY: See Section 3.8 Configuration - 
Adjusting System Parameters and Advanced Controls.
ETHERNET/COMMUNICATION SETTINGS: Includes settings for configuring the IP address via HDCP (factory 
default) or static.
CHANGING THE PORT#: On some Ethernet networks, firewall restrictions may require that the port...

2-34J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
FIGURE 2-43 JOINING ALL NETWORKS
To isolate just RS-422 communications, select “RS-232 and Ethernet Joined”. In Figure Figure 2-43 Joining 
All Networks, only projector #1 will respond to the RS-422 controller. 
To isolate just Ethernet communications, select “RS-232 and RS-422 Joined”—only projector #1 will respond 
via Ethernet.
System Integration - GPIO Connector
The GPIO connector on the...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-35020-100707-01  Rev. 1   (10-2011)
2.3.8   Projector Communications
Status LEDs
Looking from the back of the projector, the LEDs represent, from left to right; Lamp, Comm, Status, and 
Shutter. The LEDs will display the colors as shown below: 
Status LEDs#LED State
Lamp 1Off - lamp off
Yellow- Lamp time has expired and lamp should be 
replaced
Green - Lamp is on and operating correctly
Flashing Red - Lamp has malfunctioned...

2-36J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
2.4 Connecting Sources
Sources are connected to the Input Panel located at the back of the projector. Figure 2-44 Input Panel. The 
Input Panel allows one image processor board and up to 4 input cards to be inserted. The input cards are hot 
swappable i.e. they may be plugged in and out while the projector is running. The image processor should only 
be replaced when the projector is off or when...