Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-7020-100707-01  Rev. 1   (10-2011)
STEP 6 - Selecting a Source
Press one of the input keys on the remote or built-in keypad to select and display the image for the source you 
connected in Step 3.
STEP 7- Adjusting Image
Adjust the image settings, such as Brightness, Contrast, Gamma, Focus, Zoom, etc. using the direct keys on the 
remote or built in keypad. 
NOTE: Refer to Section 3 Operation for more details.
2.2 Detailed Setup...

2-8J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
FIGURE 2-10 FRONT ORIENTATION
Built-in Keypad
The built-in keypad is located at the rear of the projector. Use it similarly to the IR remote to control the 
projector. An LCD display is located above the keypad for displaying projector status.
AC Receptacle
The AC receptacle is located at the back of the projector. Use this receptacle to plug in an appropriately rated 
line cord. 
NOTE: The power...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-9020-100707-01  Rev. 1   (10-2011)
Cooling and Air Vents
Adequate airflow through the projector will prevent it from overheating. Keep all projector vents unobstructed 
and ensure adequate airflow around the projector. See Figure 2-11.
FIGURE 2-11 
Lamp Door
The lamp door is located at the rear of the projector, to provide easy access to the lamp module for 
replacement. Refer to Section 5.1.1 Lamp and Filter Replacement. The...

2-10J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
•Zoom and Focus – There are two internal lens motors that allow for quick motorized adjustment of zoom 
and focus. Adjust zoom to fit the displayed image on the screen and adjust focus to improve the clarity of the 
image.
NOTES: 1) The projection lens is shipped separately from the projector. 2) Use the lens cap when 
transporting the lens to avoid scratching and damaging the lens, which could...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-11020-100707-01  Rev. 1   (10-2011)
FIGURE 2-12 
Rules for all hoisting:
• Use at least 4 rigging points for hoisting up to 3 projectors.
• Connect safety cables, and rigging equipment suitable to your application such as clamps, cables, eyebolts, 
or straps, which accommodate the load rating. All integral, metric hardware on the projector accepts an M12 
thread only.
• Use hoisting and rigging equipment suitable to your...

2-12J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
IMPORTANT! Remove the lens before hoisting the projector.
FIGURE 2-14 NEVER USE HANDLES FOR HOISTING OR SAFETY POINTS
2.2.3 Hoisting Procedure
This procedure applies to one or more projectors. To hoist a stack, first 
stack 2 or 3 projectors according to the stacking procedure included in 
this manual. Never stack or hoist more than 3 projectors together.
1. Remove lens (recommended)
Remove the...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-13020-100707-01  Rev. 1   (10-2011)
4. Attach rigging hardware.
Attach the rigging hardware by securing your rigging 
components to the appropriate rigging points. There 
are 8 sliding points provided on the bottom. Tighten 
the nut at each required location (Figure 2-16) to 
prevent sliding. 
NOTES: 1) Use at least 4 rigging points for all hoisting. 
2) Use straps, clamps or cabling with load 
capacity adequate for the total...

2-14J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
1.Position the projectors.
• Place each projector to be stacked on a secure 
table or cart.
• Place 1 projector on its side to access its adjust-
able feet, and stacking legs (Figure 2-17).
• Orient the other projector in either upright or 
inverted position as required (remember, each 
projector in a stack must be in the same orienta-
tion).
2. Fully retract the 4 adjustable feet.
Fully retract...

Section 2: Installation and Setup
J Series 2.0, 2.4, and 3.0kW User Manual2-15020-100707-01  Rev. 1   (10-2011)
4. Loosen the rear stacking leg nuts
On the rear stacking legs (Figure 2-19), loosen 
the nuts so the legs have some lateral 
movement for easier alignment with the 
stacking mounts on the other projector.
• If upright, release on top projector
• If inverted, release on bottom projector
5. Release and remove three safety pins.
The 3 safety pins must be removed from the stacking mounts so that...

2-16J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1  (10-2011)
Section 2: Installation and Setup
  Critical Safety Procedure.
At each of the 3 stacking points, insert the safety pin fully through the holes in the stacking mounts and 
stacking legs (Figure 2-21). Ensure that each pin is fully inserted to engage the safety lock and secure the 
projectors together. Failure to engage the safety lock could cause the projectors to separate and result in 
injury or death.
  Failure to engage the...