Christie Projector DWX600-G User Manual

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-4
 
y Position the projector on a flat surface at a right angle to the screen. The 
projector (with the standard lens) must be at least 3 feet (0.9m) fr\
om the 
projection screen.
 
y Position the projector to the desired distance from the screen. The 
distance from the lens of the projector to the screen, the zoom setting,\
 and 
the video format determine the size of the projected image.
 
y For the fixed short lens, the image exits at a default angle. However, the 
lens shift feature makes the image offset variable.
 
y Lens throw ratio:
 
-
Lens 1.22~1.53 (WU/HD)
 
-
Lens 0.95~1.22 (WU/HD)
 
-
Lens 1.52~2.92 (WU/HD)
 
-
Lens 1.28-1.61 (WX)
 
-
Lens 1.0-1.28 (WX)
 
-
Lens 1.6-3.07 (WX)
 
y Do not roll the projector more than 20 degrees from side to side.
 
y Do not put the projector on either side to project an image.
3.5  Adjust the Projector Position
When you select a position for the projector, consider the size and shap\
e of 
your screen, the location of your power outlets, and the distance betwee\
n the 
projector and the rest of your equipment. Follow these general guideline\
s:
360°
 
y 360 degree operation (alone the widest axis)
20°
20° 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-5
LAMP
 
y The vertical image offset (shift) ranges for the projector are +/-100%\
 
(WXGA/WUXGA) and +/-120% (HD). The horizontal image offset (shift)\
 
range for the projector are +/-20% (WXGA/HD/WUXGA). 
 
y The method for calculating lens offset complies with Industry standards.\
 
Example for Vertical lens offset:
 
-
At 0% offset (or on axis), the center of the image is on the lens cent\
er, 
so that half of the image appears above and half appears below the 
lens center.
 
-
At +100% offset, all (or 100%) of the image will appear above the lens\
 
center.
 
-
The % offset is calculated as the ratio of the number of pixels shifted \
up/down to half the image size. Examples for WUXGA:
 
`Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
 
`Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
 
`Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
 
`Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
WUXGA Projectors:
Vertical Image Offset: 0% Offset (WUXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center 
and half of the image appears below lens 
center.
600 pixels 
above lens 
center.
600 pixels 
below lens 
center. Lens center
3.6  Calculate Lens Offset 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-6
LAMPLens center
Vertical Image Offset: 100% Offset (WUXGA)
Image has been offset 600 pixels above lens 
center, so the center of the image is now 600 
pixels above where the center of the image 
was at 0% offset (or lens center).
The offset is
+600/600 * 100% = +100%.
600 pixels 
of shift 
above lens 
center.
Vertical Image Offset: -100% Offset (WUXGA)
LAM PLens center Image has been offset 600 pixels below lens 
center, so the image has an offset of
-600/600 * 100% = -100%
600 pixels 
of shift 
below lens 
center.
Total of 
1200 pixels 
(600+600) 
of display 
are below 
lens center. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-7
HD Projectors:
LAMP
Vertical Image Offset: 0% Offset (HD)
No offset is applied - 0% offset.
Half of the image appears above lens center 
and half of the image appears below lens 
center.
540 pixels 
above lens 
center.
540 pixels 
below lens 
center. Lens center
LAMPLens center
Vertical Image Offset: 120% Offset (HD)
Image has been offset 648 pixels above lens 
center, so the center of the image is now 648 
pixels above where the center of the image 
was at 0% offset (or lens center).
The offset is
+648/540 * 100% = +120%.
648 pixels 
of shift 
above lens 
center. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-8
Horizontal Image Offset: +/-20% Offset
Lens center
Vertical Image Offset: -120% Offset (HD)
LAMPLens center Image has been offset 648 pixels below lens 
center,  so the image has an offset of
-648/540 * 100% = -120%
648 pixels 
of shift 
below lens 
center.
Total of 
1296 pixels 
(648+648) 
of display 
are below 
lens center.
Image has been offset 192 pixels 
left or right of lens center.
The image has an offset of
+192/960 * 100% = +20%, or
-192/960 * 100% = -20% -192 pixels
+192 pixels
1920 pixels 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-9
LAMP
WXGA Projectors:
Vertical Image Offset: 0% Offset (WXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center 
and half of the image appears below lens 
center.
400 pixels 
above lens 
center.
400 pixels 
below lens 
center. Lens center
LAMPLens center
Vertical Image Offset: 100% Offset (WXGA)
Image has been offset 400 pixels above lens 
center, so the center of the image is now 400 
pixels above where the center of the image 
was at 0% offset (or lens center).
The offset is
+400/400 * 100% = +100%.
400 pixels of shift 
above lens center. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-10
Vertical Image Offset: -100% Offset (WXGA)
LAMPLens center Image has been offset 400 pixels below lens 
center, so the image has an offset of
-400/400 * 100% = -100%
400 pixels of shift 
below lens center. Total of 800 pixels 
(400+400) of 
display are below 
lens center.
Horizontal Image Offset: +/-20% Offset
Lens center
Image has been offset 128 pixels 
left or right of lens center.
The image has an offset of
+128/640 * 100% = +20%, or
+128/640 * 100% = -20% -128 pixels
+128 pixels
1280 pixels 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-11
3.7  Removing and Installing the Lens
When handling the projector after lens installation, make sure the front\
 lens cap is 
placed on the lens to protect the lens surface from potential damage. Wh\
en carrying 
or moving the projector, do not handle by the lens. This may damage the \
lens, the 
chassis or other mechanical parts within the projector.
1. Center the lens: Ensure that the lens is at or near its center position. Attempting to 
remove the lens when at a large offset may cause damage to the lens asse\
mbly. Center 
the lens while the projector is switched on by pressing the lens horizon\
tal or vertical 
button and then pressing Enter.
2.  Turn Off the projector:  Turn the projector OFF.
3.  Wait for projector to cool down:  Allow the projector to cool down into standby mode 
before replacing the lens. Remove power cord after the projector has coo\
led down and 
prior to replacing the lens.
4.  Remove the lens: Remove the lens ring cover.  Rotate the lens counter-clockwise by a quarter to release the lock. Remo\
ve the lens 
through the front of the projector.
Installation Steps:
5.  Install the new lens:  Fully insert the lens assembly straight into the lens mount without 
turning. Rotate the lens cap clockwise to lock the lens in place. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-12
3.8  Cable Cover Installation
1.  Rotate the cable cover and insert the two guide pins into the guide hole\
s.
2.  Press and hold both lower corners of the cable cover while inserting the\
 sheet clips into the projector casing.
Guide Hole
Guide Pin
Hold and Press Here 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 4: Operation
4-1
4.  OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allo\
w you 
to make image adjustments and change a variety of settings.
• Most of the projector controls are accessed from within the projector me\
nu 
system. There are several groups of related functions, with each group 
selectable from the Main menu as shown below. Press the MENU button on 
the remote control or on the built-in keypad on the rear of the projecto\
r to 
display the main menu.
•  Use the arrow keys to navigate within the menu and adjust a setting up o\
r 
down.
•  Press ENTER to select a highlighted menu item or use it to change or 
accept a value.
•  Select the next item that you want to adjust in the menu and adjust it a\
s 
described above.
•  Press EXIT to return to the previous menu or exit menus if at top level.\