Christie Projector DWX600-G User Manual

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-3
Right View
LAMP
Left View
1
2
3
4
Ind. Part NameDescription
1 Lamp Door Use the lamp door to access the lamp module.
2 LED Status Indicators Displays the status of the projector. They are (from left 
to right): LAMP, STATUS, and PIC MUTE.
3 Built-in Keypad Controls the projector.
4 Cooling Air Vents 
(Intake) Keep these vents unobstructed to prevent the projector 
from overheating. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-4
2.2  Built-in Keypad
7
8
9
102
4
5
611
1
3
Ind. Key Name
Description
1 Power Turn the projector on or off
2 Menu Display menus
3 Enter Confirm a selection
4 Auto Automatically optimize image
5 Lens Adjust the lens vertical or horizontal offset setting
6 Focus Adjust focus
7 Exit Return to previous level or exit menus if at top level
8 Arrow Keys  
y Adjust a setting UP or DOWN
 
y Navigate within a menu
9 Input Select an input for the main or PIP/PBP image
10 Picture Mute Display or blank the video image.
11 Zoom Adjust zoom 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-5
2.3  Input/Output (I/O) Panel
Ind.Connector Name Ind.Connector Name
1 Remote IN 8Mini USB
2 Remote OUT 9 USB Type A
3 Component IN 10 DisplayPort
4 CVBS 11 HDMI
5 S-Video 12 VGA-IN
6 RS232 13 VGA OUT
7 Ethernet 14 DVI
1 2 3 4 5
78 9
1011 12 13 14
6 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-6
2.4  Remote Control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 16
17
18
19
20
21
22
23
24
25
26
27
28
29 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-7
Ind. Key NameDescription
1 Picture Mute Display or blank the video image.
2 Power on Turn projector ON.
3 Gamma Adjust mid-range levels.
4 Bright Adjust amount of light in the image.
5 PIP/PBP Turn PIP/PBP ON/OFF.
6 Size Adjust the PIP/PBP size
7 Number Keys Enter a number, such as a channel, value, etc.
8 Help Display context-sensitive help.
9 Menu Display menus.
10 Arrow Keys  
y Adjust a setting UP or DOWN.
 
y Navigate within a menu.
11 Test Display a test pattern.
12 Auto Automatically optimize image.
13 OSD Use to hide or show menus.
14 Keystone H Adjust the horizontal keystone.
15 Keystone V Adjust the vertical keystone.
16 Standby Turn projector OFF.
17 Contrast Adjust difference between dark and light.
18 Hot-key Select your preset keys quickly.
19 Swap Swap the main and PIP/PBP images.
20 Layout Adjust the PIP/PBP layout.
21 Focus Adjust focus to improve image clarity as desired.
22 Zoom Adjust zoom to achieve a desired image size.
23 Proj Key Change the remote ID. Press Proj Key then a number 
between 1 and 9 to assign an ID. Press PROJ then 
number 0 to return to the universal remote ID.
24 Exit Return to previous level or exit menus if at top level.
25 Enter  
y Select a highlighted menu item.
 
y Change or accept a value.
26 Input Select an input for the main or PIP/PBP image.
27 Info Display source image information.
28 Lens H Horizontal Lens Shift - Adjust the position of the image 
horizontally.
29 Lens V Vertical Lens Shift - Adjust the position of the image 
vertically. 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-8
2.5  LED Status Indicators
The LED status indicators are located on the right side of the projector\
. Each 
LED is defined below. 
y LAMP LED
LED Status
Projector State
Red (short blink) Failed to strike lamp after 5 attempts (strike attempts will 
stop).
Lamp has unexpectedly shut down (system goes into cool 
down state). 
Yellow (no blink) Lamp time has expired and lamp should be replaced. 
(projector also begins to display the replace lamp OSD 
message at startup).
Green (no blink) Lamp is ON and operating correctly
Green (short blink) Projector lamp is switching on
Off Lamp is off
 
y STATUS LED
LED Status
Projector State
Off Projector is in OFF state (without AC plug in)
Off, but keypad LED 
is on Projector is in standby mode (AC plug in)
Green (no blink) Projector is powered up and operating normally
Flashing Yellow Projector is in cool down mode or startup mode
Flashing Green/
Yellow Projector is in flash update state
Red (short blink) Fan failure
Red (no blink) Over-temperature
Green (blink very 
quickly) Projector communications (Read/Write EEPROM) 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 2: Introduction
2-9
 
y PICTURE MUTE LED
LED Status
Projector State
Green Picture mute is off – image is displayed
Yellow Picture mute is on – image is black 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-1
3.  INSTALLATION
3.1  Connect to Computer
NOTE: 
™The diagram shows the cables/connectors that may be used to connect to v\
arious devices.  
™Due to the difference in applications for each country, the accessories \
required in some regions may be different from those 
shown.
 
™This diagram is for illustrative purposes only, and does NOT indicate th\
at these accessories are supplied with the projector.
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1 USB Type B Mini 
Cable 4 HDMI Cable
7 RS232 Cable
2 USB Type A Cable 5 VGA in Cable 8DVI Cable
3 DisplayPort Cable 6 VGA out Cable 9 Power Cord
Desktop Laptop
51623478
9 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-2
3.2  Connect to Video Equipment
NOTE: 
™The diagram shows the cables/connectors that may be used to connect to v\
arious devices.  
™Due to the difference in applications for each country, the accessories \
required in some regions may be different from those 
shown.
 
™This diagram is for illustrative purposes only, and does NOT indicate th\
at these accessories are supplied with the projector.
Component video output equipment DVD playerVideo cassette recorder
41
5
7
8
23
6
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1 HDMI Cable 4 S-Video Cable 7 3 RCA Component 
Cable
2 Component (YPbPr)
Cable 5 VGA to RBG SCART
815-pin to 3 RCA 
Component/HDTV 
Adapter
3 CVBS Cable 6 VGA in Cable 
						

							G Series User Manual020-000648-01  Rev. 3 (02-2014)
Section 3: Installation
3-3
3.3  Turn the Projector On
1.  Ensure that the power cord and signal cable are securely connected. The \
Power button on the built in keypad is illuminated. 12345678910111213141516171819202.  Turn on the lamp by pressing “” on the remote control or press “” on 
the built-in keypad. The Status LED is yellow with a long blink. 
1234567891011121314151617181920 
The startup screen displays in approximately 10 seconds. 
3.  Turn on the source. Select Input Key on the remote control to select an \
 input source (VGA, BNC, HDMI, Component, S-Video or Composite 
Video). 
12345678910111213141516171819204.  The projector detects the source you selected and displays the image.
NOTE: 
™The first time the projector is used, the preferred language may be selected from the main menu after the startup screen is 
displayed.
3.4  Turn the Projector Off
1.  Press “” on the built-in keypad or on the remote control to turn off the 
projector. A warning message will appear on the displayed image.
2.  Press 
“” again to confirm your selection. If you do not press “” again, 
the warning message will disappear after 10 seconds.
 Input Key1234567891011121314151617181920
 Power on1234567891011121314151617181920
 Status LED1234567891011121314151617181920
 Power on1234567891011121314151617181920