Christie Projector CP2230 User Manual

							Appendix B: Serial API
CP2230 User ManualB-25020-100430-07 Rev. 1 (05-2014)
CxxxReplace xxx with the channel num ber. Valid range is 101 - 164.
NONE Select source format for the current channel.
EXAMPLES:
(SRF+C108 “XXX”) Use file “XXX” on channel 108
(SRF+C108?) Get source fi le name on channel 108
(SRF?L) List all entrie s of source control
(SRF+RFSH 1) Refresh TI file list
System Status (SST)
R
etrieve the various system status groups.
SUBCODEDESCRIPTION OF USE
ALRM Returns a summary of any active alarms
CONF Returns configuration data -  model, sn, build date, etc
COOL Returns cooling data - c ooling fans, air flow, etc
HLTH Returns system health
INTE Returns interlock data
LAMP Returns lamp operational data.
NONE Returns information on all status  groups, with one message per item.
PERI Returns peripherals da ta - Cine-IPM, etc
SECU Returns security data
SERI Return serial numbers
SIGN Returns signal data - freq, etc.
SYST Returns system data - power, hour s of use, shutter open, etc
TEMP Returns temperature data
VERS Returns version numbers
EXAMPLE:
(SST+ALRM?) returns (SST+ALRM!000 002 “101”  “P rism temperature”) where parameters are: 
P1=index number, 
P2=error level, 
P3=value, 
P4=description. 
Error level is:
0=no errors or warnings, 
1=warning, 
2=error, 
3=error and warning
Stop DLP Communication (STP)
Stop communications to DLP® Cinema Electronics temporarily, i.e. for DLP software upgrading. 
						

							B-26CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
SUBCODEDESCRIPTION OF USE
NONE 0 - restart DLP communications; 
1 - stop DLP communications.
EXAMPLES:
(STP 0) Restart  DLP communication
(STP 1) Stop DLP communication
(STP?) Request current state. Example re sponse is (STP!000)
cinema projector Platform and Motherboard Related Information (SYS)
Query only command that returns version information.
SUBCODEDESCRIPTION OF USE
BACB Return backplane version information.
FA C B Return faceplate version information.
PIBB Return PIB version information.
EXAMPLES:
(SYS+BACB?) Returns backpl ane version information.
Target Color Gamut (TCG)
Set the Target Color Gamut file. This file describes desired output colorimetry from the cinema projector. For this 
control to function the Measured Co lor Gamut Data must be accurate.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel  number. Valid range is 101 - 164.
NONE Select target color gamut for the current channel.
EXAMPLES:
(TCG+C108 “Atlantis”) Use fi le “Atlantis” on channel 108
(TCG+C108? ) Get target colo r file name on channel 108
(TCG?L) List all available entries of target color control
Enable 3D (TDC)
Enable/disable 3D on the specified channel or the current channel. This controls the frame rate multiplication fea-
tures that allow for simulated three dimensional image projection.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel  number. Valid range is 101 - 164.
NONE Select 3D enable for the current channel
EXAMPLES:
(TDC+C108 1) Enable 3D on channel 108
(TDC+C108?) Get 3D setting on channel 108
(TDC?) Get current 3D status 
						

							Appendix B: Serial API
CP2230 User ManualB-27020-100430-07 Rev. 1 (05-2014)
3D DARK TIME (TDK)
Set dark time for 3D control. This controls how much time between displayed images the output remains dark to 
allow for the glasses on other gating m echanism to flip between the eyes. 
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel num ber. Valid range is 101 - 164.
NONE Select dark time for the current channel
EXAMPLES:
(TDK+C101 1) Set dark time to 1 on channel 101
(TDK+C101?) Get dark time on channel 101
Output Reference Delay (phase) (TDP)
Set output reference delay phase for 3D control. This is an  additional control for output timing relative to input 
timing. The data range is -180 to 180.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel num ber. Valid range is 101 - 164.
NONE Select output reference delay phase for the current channel
EXAMPLES:
(TDP+C101 1) Set output referenc e delay phase to 1 on channel 101
(TDP+C101?) Get output refere nce delay phase on channel 101
3D L/R Display Reference (TDR)
Set the L/R display reference for 3D control.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel num ber. Valid range is 101 - 164.
NONE Select L/R display reference for the current channel 
EXAMPLES:
(TDR+C101 1) Set L/R display re ference to 1 on channel 101
(TDR+C101?) Get L/R display reference on channel 101
Output Reference Delay (time) (TDT)
Set output reference delay time for 3D control. This command controls how much delay between the input and out-
put reference timing.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel num ber. Valid range is 101 - 164.
NONE Select reference delay for the current channel 
EXAMPLES:
(TDT+C101 1) Set output reference  delay time to 1 on channel 101
(TDT+C101?) Get output referenc e delay time on channel 101 
						

							B-28CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
L/R Display Sequence (TFD)
Set L/R Display Sequence for 3D control. This selects which signal is considered first in the source signal, the left 
or the right. 
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel  number. Valid range is 101 - 164.
NONE Select L/R display sequenc e for the current channel 
EXAMPLES:
(TFD?L) List all entries on Input Frame Dominance control
(TFD+C101 1) Set Input Frame  Dominance to 1 on channel 101
(TFD+C101?) Get Input Fram e Dominance on channel 101
3D Frame Rate Multiple (TFR)
Setup frame rate multiple for 3D control
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel  number. Valid range is 101 - 164.
NONE Select 3D frame rate fo r the current channel. 
EXAMPLES:
(TFR?L) List all entries on the frame rate multiple factor
(TFR+C101 3) Set frame rate multiple to “4:2” on channel 101
(TFR+C101?) Get frame ra te multiple on channel 101
Get Certificates (TIG)
Gets the LD or ICP certificate.
SUBCODEDESCRIPTION OF USE
ENGC Retrieve LD Certificate
ICPC Retrieve ICP Certificate
EXAMPLES:
(TIG+ENGC?) Gets th e LD certificate
(TIG+ICPC?) Gets the ICP certificate
3D Input Reference (TIR)
Setup the Input Refere nce for 3D control.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel  number. Valid range is 101-164.
NONE Select input reference for the current channel.
EXAMPLES:
(TDK+C101 “Use GPI (polarity=true)”) set Input Refe rence to ‘Use GPI (polarity=true)’ on channel 101
(TDK+C101?) get Input Refe rence for channel 101 
						

							Appendix B: Serial API
CP2230 User ManualB-29020-100430-07 Rev. 1 (05-2014)
Time/Date (TMD)
Set/get the time, date and time zone.
SUBCODEDESCRIPTION OF USE
DATE Get the date in the form yyyy/mm/dd. Read-only.
DSTA Set/get the daylight savi ngs time adjust value.
TIME Set/get the local time in the form hh:mm:ss. Ready only.
TOFF Set Time Offset in seconds (± 900 sec onds). Must be powered ON. (Write-only)
ZONE Set/get the time zone
EXAMPLES:
(TMD+DSTA?) 0 or 1 (DST OFF or DST ON)
(TMD+DSTA 0) Turn daylight savings OFF (0) or ON (1)
(TMD+ZONE 20) Set time zone to EST
(TMD+TIME? ) Get local  time (TMD+TIME! 17:50:45)
(TMD+TOFF 120) Increase the time by two minutes.
(“TMD+TOFF: Disabled Control”) Error  message returned when power is OFF.
(“TMD+TOFF: LD Real Time Cloc k Offset range for time adjustment has been exceeded.”) 
3D Output Reference Polarity (TOP) 
Setup output timing signal reference polarity for 3D control. 
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel  number. Valid range is 101-164.
NONE Select output reference polarity for the current channel.
EXAMPLES:
(TOP+C101 1) Set Output Referenc e Polarity to 1 on channel 101
(TOP+C101?) Get Output Refere nce Polarity on channel 101
User ID (UID)
Allows users to login to the serial interface.
SUBCODEDESCRIPTION OF USE
NONE None
EXAMPLES:
(UID “username” “password”) Login a user
(UID) Logout the current  user, also happens automatica lly when a new user logs in
(UID?) Display the current logged  in user and their access level 
						

							B-30CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
Zoom Lens Position Adjustment (ZOM) 
Adjust lens to specific zoom position with a specified direction (1, -1). NOTE: This command can only be used to 
update the current ILS file . Changing the zoom for the current channel will change the zoom for any channel using 
the same ILS file.
Use command wi thout subcode:
•  If ILS is ON, motor will move to specified steps and save data to the active channel.
•  If ILS is OFF, motor will move to specified  steps, do not save data to the active channel.
SUBCODEDESCRIPTION OF USE
BACN Motor backlash in negative  direction. Read-only. 
BACP Motor backlash in positive  direction. Read-only. 
CALB Calibrate travel range and backlash on specified. Only valid parameter for this command is 1. Set only 
command.
Cxxx Replace xxx with the channel  number. Valid range is 101-164.
NONE Moving lens mount to a sp ecified vertical position.
RNGN Motor moving range in negati ve direction. Read-only. 
RNGP Motor moving range in positive direction. Read-only. 
RSET Move motor to the center flag then move back to current position. Only valid parameter for this command 
is 1. Set only command.
STRT Start motor moving in specified dire ction, where direction can be (-1, 1). Write-only for v1.3 or newer.
STOP Stops the motor. Write-only for v1.3 or newer.
MOVR Moves the motor a given number of steps based on th e current location. Write-only for v1.3 or newer.
EXAMPLES:
(ZOM 500 1) Move lens to position 500 with positive approach
(ZOM 500 -1) Move lens to posit ion -500 with negative approach
(ZOM+C101 -500 1) Set lens z oom position for channel 1 to -500 with positive approach.
(ZOM ?) Return current motor position
(ZOM + CALB 1) Calibrate the zoom
(ZOM + RSET 1) Reset the zoom
(ZOM+STRT 1) Starts motor  moving in positive direction
(ZOM+STOP) Stops motor
(ZOM+MOVR -100) Move motor 100  steps in negative direction
(ZOM+MOVR 200) Move motor 200  steps in positive direction. 
						

							*000-101832-07*
ASSY TECH DOCS CP2230 
						

							Japan
ph: 81-3-3599-7481
South Korea
ph: +82 2 702 1601
For the most current technical documentation, please visit  www.christiedigital.com 
USA – Cypress
ph: 714-236-8610
Canada – Kitchener
ph: 519-744-8005United Kingdom
ph: +44 118 977 8000
France
ph: +33 (0) 1 41 21 00 36
Germany
ph: +49 2161 664540Eastern Europe
ph: +36 (0) 1 47 48 100
Middle East
ph: +971 (0) 4 299 7575
Spain
ph: + 34 91 633 9990 Singapore
ph: +65 6877-8737
Beijing
ph: +86 10 6561 0240
Shanghai
ph: +86 21 6278 7708
Corporate offi ces Worldwide offi ces