Christie Projector CP2230 User Manual

							Cinema Projector Menus
CP2230 User Manual6-39020-100430-07 Rev. 1 (05-2014)
6.15.5 Time Setup Window 
Use the Time Setup window to change cinema projector time settings. To  open the Time Setup window you 
need Administrator or Service permissions. Tap  Menu > Administrator Setup  > Time Setup. 
Table 6.26 Administrator  Setup: Time Setup Window
ControlDescription
Time Zone The time zone where the cinema projector is installed.
24 Hour Time  Displays time in a 24-hour format.
Adjust for Daylight Savings 
Time Automatically adjusts the time for daylight savings.
Time Offset Increases or decreases the cinema projector time.
Apply Time
Adjustment Applies time adjustment settings.
 Figure 6-31 Administrato
r Setup: Time Setup Window
1
2 
						

							6-40CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Cinema Projector Menus
6.15.6 Scheduler Window 
Use the Scheduler window to schedule when the cinema projector turns on or off. To open the Scheduler 
window you need Administrator or Service permissions. Tap  Menu > Administrator Setup  > Scheduler . 
Table 6.27 Administrator Setup: Scheduler Setup Window
ControlDescription
Enable Scheduler Enables or disables the scheduler.
Delete All Deletes all scheduled events.
 Figure 6-32 Administrator Setup: Scheduler Window 
						

							Cinema Projector Menus
CP2230 User Manual6-41020-100430-07 Rev. 1 (05-2014)
6.15.7 Communications Configuration Window
The Communications Configuration  window configures the Ethernet settings, serial communication 
parameters, SNMP settings,  and remote access settings.
 Figure 6-33 Administrator Setup: Communications Configuration Window
1
23
45 
						

							6-42CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Cinema Projector Menus
Table 6.28 Administrator Setup: Communications Configuration Window
6.15.8 Network Devices Setup Window
Use the Network Devices window to view the web interface  of external peripherals such as Christie ACT and 
the Integrated Media Block (IMB).  Tap  Menu > Administrator Setup >  Network Devices Setup.   
 Figure 6-34 Administrator Setup: Network Devices Setup Window
ControlDescription
1: Device Name The name  of the network device.
IP Address The IP address of the network device. 
Subnet Mask The subnet mask to  which the address belongs.
Gateway The IP address  for the network gateway.
Apply Applies Ethe rnet settings.
Serial Speed (Baud) The baud rate of  the serial port. The default is 115200. 
Enable SNMP Enables SNMP. 
SNMP V2 / SNMP 
V3 The SNMP protocol type. Contact Christie
 for the SNMP V3 user ID and password.
Management IP The IP address where SNMP  information and notifications are sent. 
Download MIB to 
USB Sends the SNMP Management
 Information Base (MIB) file to a USB drive. 
Apply Applies SNMP settings.
Serial Access Grants access to serial connections.
Ethernet Access Grants access to Ethernet connections. 
						

							Cinema Projector Menus
CP2230 User Manual6-43020-100430-07 Rev. 1 (05-2014)
Add a Network Device
1. Tap Menu >  Administrator Setup  > Network Devices Setup
2. In the Device Name  area, select the check box to the  left of the device you are adding. 
3. Enter the device name in the Device Name  field.
4. In the  URL field, enter the URL of the device you are adding
.
5. Click  Menu, select  Network Device , and then select a network device. The web interface for this device 
appears.
6.15.9 GPIO Setup Window
Use the GPIO Setup window to config ure the input and output settings of the GPIO interface. To open the 
GPIO Setup window you need Administrator or Service permissions. Tap  Menu > Administrator Setup  > 
GPIO Setup .
Table 6.29 Administrator  Setup: GPIO Setup Window
ControlDescription
Rising Edge The rising edge for the signal.
Falling Edge The falli ng edge for the signal.
Trigger The trigger that is sent  when the function is activated.
Output The output that triggers the GPIO signal.
 Figure 6-35 Administrato r Setup: GPIO Setup Window
12 
						

							6-44CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Cinema Projector Menus
6.15.10 Foot Lamberts Calibration Window
Use the Foot Lamberts Calibra tion wizard to calibrate the internal light  meter to Foot Lamberts. When you run 
Foot Lamberts Calibration during a sh ow, the show stops. To run the Foot Lamberts Calibration wizard you 
need Administrator or Service permissions. Tap  Menu > Administrator Setup  > Foot Lamberts 
Calibration .
 Figure 6-36 Administrator Setup: Foot Lamberts Calibration Start Window 
						

							Cinema Projector Menus
CP2230 User Manual6-45020-100430-07 Rev. 1 (05-2014)
6.15.11 User Accounts Window
Use the User Accounts  window to manage users, passwords, and  user access rights. Depending on your login 
level, you will be able to manage users having the same or fewer access rights as you. Tap  Menu > 
Administrator Setup  > User Accounts.
Table 6.30 Administrator Se tup: User Accounts Window
ControlDescription
User Name and Permission A list of  all users and their permissions. 
Add Adds a username, password and  permission level for a new user.
Edit Edit user passwords and permissions.
Delete Deletes a user account.
 Figure 6-37 Administrator Setup: User Accounts Window 
						

							6-46CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Cinema Projector Menus
 Figure 6-38 Add a New User Window 
						

							Cinema Projector Menus
CP2230 User Manual6-47020-100430-07 Rev. 1 (05-2014)
6.15.12 Upgrade Window
Use the Upgrade window to upgrade the cinema projector software. You must have Administrator or Service 
permissions to upgrade software
.
Upgrade: File Selection Window
Table 6.31 Upgrade: File Selection Window
Control Description
Available Upgrade Files Lists all the upgrades currently stored  in the FTP directory of the cinema 
projector.
Disk Space Used A visual representation of the amount of used disk  space on the cinema projector. 
Free Space The amount of available free space on the cinema projector. 
Upload Uploads a file.
Remove Deletes an upgrade file.
Next Opens the Extraction window.
 Figure 6-39  Upgrade: File Selection Window  
						

							6-48CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Cinema Projector Menus
Upgrade: Package Details Window
Table 6.32 Upgrade: Package Details Window
6.15.13 System Access Window
The System Access  window provides access to the Wind ows operating system of the TPC.
Control Description
Upgrade Different 
Components OnlyUpgrades system components that are newer or
 older than the currently installed version.
ICP Only Force Install Forces an ICP install rega rdless of what current version is installed. 
Force Upgrade All Upgrades all components in the upgrade package.
Factory Install Removes all configurations and upgrades all components. 
Upgrade Different Components 
Only Upgrades system components that are newer or
 older than the currently installed version.
 Figure 6-40 Upgrade: Package Details Window