Christie Projector CP2230 User Manual

Appendix B: Serial API
CP2230 User ManualB-15020-100430-07 Rev. 1 (05-2014)
NONEReturn lamp usage for current lamp in hours.
TLSK Return total lamp strikes on the installed lamp
EXAMPLES:
(LPH?) Get usage in hours
(LPH+FLSK?) Get lamp strikes 
Lamp Intensity (LPI)
Set lamp intensity setpoint. The value is used when la mp mode is set to LiteLOC™. The cinema projector will 
adjust the Lamp Power to maintain this intensity.  NOTE: This command can only be  used to update the current 
lamp file . Changing...

B-16CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
Lamp Mode (LPM) 
Set lamp mode to constant power or LiteLOC™ for global and per channel. NOTE: This command can only be 
used to update the current lamp file . Changing the lamp power for the current channel will change the lamp power 
for any channel using the same lamp file.
SUBCODEDESCRIPTION OF USE
Cxxx Replace Cxxx with the channel number. Valid range is 101-164.
NONE Set lamp mode for the current channel.
EXAMPLES:
(LPM 0)...

Appendix B: Serial API
CP2230 User ManualB-17020-100430-07 Rev. 1 (05-2014)
RNGPMotor moving range in posi tive direction. Read-only.
RSET Move motor to the center flag then move back to cu rrent position. Only valid parameter for this command 
is 1. Set only command.
STRT Start motor moving in specified direction, where di rection can be (-1, 1). Write-only for v1.3 or newer.
STOP Stops the motor. Write-only for v1.3 or newer.
MOVR Moves the motor a given number of steps based on  the current location....

B-18CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
DATASet/Get active MCGD measurement values. The order is RedX, RedY, GreenX,  GreenY, BlueX, BlueY, 
WhiteX, WhiteY, BlackX, BlackY. Th e range for each value is 0 - 100000. The values represent MCGD 
measurement values multiplied by 100000.
SAVE Saves the active MCGD measurement values to a  new or existing MCGD file. (SET Only Command)
EXAMPLES:
(MCG+C108 “Nominal”) Use file “Nominal” on channel 108
(MCG+C108?) Get measured...

Appendix B: Serial API
CP2230 User ManualB-19020-100430-07 Rev. 1 (05-2014)
MAC0Gets the MAC address of  the cinema projector
SUB0 Set the WAN subnet mask for the cinema projector
EXAMPLES:
(NET+ETH0 192.168.1.35) Set new IP address on the MGMT Ethernet controller
(NET+GATE 192.168.0.1) Set the gateway 
(NET+SUB0 255.255.255.0) Set the subnet mask on the MGMT Ethernet controller
(NET+HOST MyHostName) Set the host name 
(NET+ETH0 ?) Retrieve IP address from the MGMT  Ethernet controller. (NET+ETH0!...

B-20CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
PCT In Use (PCU)
Sets or returns PCT In Use and enables or disables PCT for the active or selected channel.
SUBCODEDESCRIPTION OF USE
Cxxx Replace xxx with the channel number. Vali d Range is 101 - 164 0-disabled 1-enabled.
NONE Select PCU for the current ch annel. 0-disabled 1-enabled.
EXAMPLES:
(SIU?) Get current value for PCU In Use for the activ e channel. Returns 1 for enabled or 0 if disabled.
(SIU 1) Set PCU In Use on...

Appendix B: Serial API
CP2230 User ManualB-21020-100430-07 Rev. 1 (05-2014)
Power (PWR)
Change the power state of the cinema projector. Data can be: 
3 - Power OFF - all electronics power OFF except cinema projector Contro l Module (PCM). Its also called 
Standby mode. 
1 - Power ON - cinema projector is powered ON with lamp ON. 
0 - Full power mode - cinema projector is ready for lamp ON. 
11 - Warm up. Read only, its middle status between standby and full power mode. 
10 - Cool down. Read only, cinema...

B-22CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
Restore Whole or Part of a Backup (RST)
Restore files from a backup file.
SUBCODEDESCRIPTION OF USE
CHAN Restore only channel settings.
CONF Restore only configuration settings.
FULL Restore all settings including channe l, config, preferences, and user.
ICPF Restore only ICP files. Th e cinema projector must be in power up mode.
LIST List backup files in the FTP root that can be used with restore.
PREF Restore only preferences....

Appendix B: Serial API
CP2230 User ManualB-23020-100430-07 Rev. 1 (05-2014)
PONDSet the power on date and time, setting the date/time to  empty (“”) will turn off power on scheduling until 
a new date/time has been set.  Format “yyyy-mm-dd hh:mm”
POFD Set the power off date and time, setting the date/time to  empty (“”) will turn off power off scheduling until 
a new date/time has been set.  Format “yyyy-mm-dd hh:mm”
EXAMPLES:
(SC+BPON 1) Disable power on scheduling  events, it will still be possible to...

B-24CP2230 User Manual020-100430-07 Rev. 1 (05-2014)
Appendix B: Serial API
CxxxReplace xxx with the channel  number. Valid range is 101 - 164.
NONE Select input for current channel
EXAMPLES:
(SIN?) Get current input port
(SIN?L) Show entries on the list
(SIN 1) Set current input port to entry with index 1
(SIN+C101 ?) Get input port on channel 101
(SIN+C101 1) Set input on channel 101
SNMP Agent Configuration (SNM)
This control will set the various configuration options for SNMP Agent
SUBCODEDESCRIPTION...