Christie Digital Systems Ds+60 Users Manual

Section 3: Operation 
 
Christie DS+60 User’s Manual     3-57  
 
Occasionally the projector will encounter an error condition that can interrupt normal 
operation. Such a condition can be caused by a simple invalid keypad entry, an input 
signal error (most common) or a system error. The manner in which users are to be 
notified of error conditions is set in the Menu Preferences menu: 
• To see error messages displayed on-screen, select the “
Screen” option 
• To be notified via a serial communication...

Section 3: Operation 
3-58   Christie DS+60 User’s Manual  
Other Signal Error Messages 
In addition to the common Bad Sync and “No Signal” errors, you may encounter a 
signal error message indicating that HSYNC and/or VSYNC are either too fast or too 
slow. When such a message appears, check the frequencies shown in the Status menu. 
If they are correct, then the signal is not recognized by the projector. On some PCs 
you may be able to change the settings to generate a compatible signal. If the...

Section 3: Operation 
 
Christie DS+60 User’s Manual     3-59  
 Code Description GENERAL 12  Software bug. Contact dealer/factory. 13  Flash memory corrupted. Download new software. 14  Engineering-only programming is complete. Call Christie, replace TIPM. 15  Attempting to download code without being in boot mode 16  Invalid interrupt. Power off/on. If it persists, contact dealer/factory. 18  Attempting to program boot mode without jumper LAMP FAILURES 21  Lamp compartment too hot 25  Lamp 1 not...

Section 4 
Maintenance  
 
  Christie DS+60 User’s Manual     4-1 
 
The projector is an international regulatory agency approved product designed for safe 
and reliable operation. It is important to acknowledge the following precautions while 
operating the projector to assure complete safety at all times. 
 WARNING 
Always remove the lens when shipping the 
projector.  
 
 WARNING 
NEVER look directly into the projector lens.  
The high brightness of this projector 
could cause permanent eye damage....

Section 4: Maintenance  
4-2   Christie DS+60 User’s Manual  
 
Operate the projector in an environment, which meets the operating range as specified 
in Section 6 – Specifications. 
◊ Do not operate the projector close to water, such as near a swimming pool. Do not 
operate in extremely humid environments. 
◊ Do not place the projector on an unstable cart, stand or table. A projector and cart 
combination should be used with care. Sudden stops, excessive force and uneven 
surfaces may cause the...

Section 4: Maintenance  
 
Christie DS+60 User’s Manual     4-3  
◊ The projector is equipped with a three-wire plug having a third grounding pin. 
This is a safety feature – if you are unable to insert the plug into an outlet contact 
an electrician to have the outlet replaced. Do not defeat the safety purpose of this 
grounding-type plug.  
 
Slots and vents in the projector provide ventilation. Never block or cover these 
openings. This ensures reliable operation of the projector and prevents...

Section 4: Maintenance  
4-4   Christie DS+60 User’s Manual  
 
 WARNING 
Always power down and unplug the projector before 
cleaning or servicing. 
 
Table 4.1. Maintenance Guide 
Part Description Frequency How to clean 
Lens  As required 
CLEAN: Clean if absolutely necessary. A 
small amount of dust on the lens has very 
little affect on picture quality. 
To clean: Apply a solvent such as acetone, 
alcohol or vinegar sparingly to clean, lint-
free lens tissue. Wipe across the surface of 
the lens. Do...

Section 4: Maintenance  
 
Christie DS+60 User’s Manual     4-5  
 
The optional IR remote uses two AA size, 1.5V alkaline batteries. To replace the 
batteries simply turn the remote over and push out the cover using the finger groove, 
as shown in (1) Figure 4.1.  
Remove and properly discard the old batteries. Insert new batteries in the proper 
positive/negative orientation as shown etched in the bottom of the compartment (2). 
Replace the cover by inserting the tabbed end into the opening and...

Section 4: Maintenance  
4-6   Christie DS+60 User’s Manual  
To replace a lamp: 
1. Press 
 to power down the projector and allow the lamp to cool for 
approximately 5 minutes after the fans have turned off before continuing with 
Step 2. If required, you can switch lamp modes and cut power to the lamp you 
want to replace without having to power down the projector and interrupt a 
presentation.  Check the Lamp menu to ensure the lamp operation mode has been 
switched to the other lamp. Allow the lamp...