Christie Digital Systems Ds+5k, Kc-8k, Dw3k-6k, Kc, Hd5k, Kc-8k, Kc, Mirage S+2-4-8k, Dlv1400-dx, 1920-dx, Matrix S+2k, 4000, Hd4k Users Manual

 Section 3: Operation 
013-100199-04  3-33. 
SELECT COLOR ADJUSTMENT: In “Select Color Adjustment”, 
choose an overall color palette for all images. The “Max 
Drives” factory default simply drives all three colors at their 
maximum level so that they are fully on and cannot be 
changed. The two other pre-defined color adjustment 
choices—SD Video and HD Video—apply a color gamut 
optimized for video sources (standard or high-definition). 
Alternatively, you can specify a color temperature. This 
enables...

Section 3: Operation  
3-34 013-100199-04   
Simulation 3D — SUBMENU OF ADVANCED IMAGE SETTINGS 
Use the options in the Simulation 3D 
menu to make the timing adjustments 
necessary for realistic simulation and 
3D images. 
NOTES: 1) Available in Mirage 
projectors only. 2) For complete 3D 
application notes, refer to the 
separate Using 3D in Mirage
 manual 
provided with the Mirage projector. 
FRAME DELAY MONITOR — This slide bar monitors the latency between input and 
output. For best results, the bar...

 Section 3: Operation 
013-100199-04  3-35. 
  
With your sync cable, Z-screen and, if desired, emitter connected as described in the 
Using 3D in Mirage
 manual, select the option suited to your 3D configuration (see 
above). If Frame Delay is two (or 0), do not invert; if frame delay is one or three, 
invert. Generally, an “Unlocked” setting is synchronized with the incoming L/R signal 
rather than the vertical sync output, and may be needed only with multi-projector 
installations in which the...

Section 3: Operation  
3-36 013-100199-04   
2. STILL: For static images with no motion, such as graphics from a CD. 
3. 
MOTION: For video images that did not originate from film, or for moving 
computer-generated images. 
4. 
FILM: For video images that originated from film. This will optimize image quality 
and stability. 
 
FILM MODE THRESHOLD — This setting determines how sensitively the projector can 
detect if an incoming video signal originated from film or not. It should not require 
adjustment....

 Section 3: Operation 
013-100199-04  3-37. 
Auto Power-up 
Enter a checkmark to enable the projector to automatically power up after losing 
power due to a power failure or due to unplugging the projector during operation. 
Note that unsaved display adjustments may be lost. 
Set Date & Time 
Enter/read the current year-month-day and hour-minute-second. Changes here reset 
the projector’s real-time clock. 
Menu Preferences 
— SUBMENU 
Adjust the appearance, content 
and/or location of on-screen 
menus...

Section 3: Operation  
3-38 013-100199-04   
SPLASH SCREEN SETUP —Use the Splash Screen to choose when you would like to 
display a special introductory splash screen image, such as your company logo, 
graphic or message. 
• Always Off = A splash screen never appears 
• Always On = A splash screen is always on behind the current display image, 
similar to wallpaper. 
• Start-up Only – The splash screen logo appears at projector start-up only. 
• Start-up And No Signal – A splash screen appears at...

 Section 3: Operation 
013-100199-04  3-39. 
 
SEPARATE: 
Select “Separate” (factory default) to keep RS232, RS422 and Ethernet 
messages on their respective paths instead of being broadcast to the other types of 
ports. In Figure 3.8A, RS422 controls only the projector to which it is connected. In 
Figure 3.8B, either RS232 or RS422 will control the network. 
 
Figure 3.8. Using the “Network Routing” Option 
RS232 AND RS422 JOINED: Messages originating from an RS232 or RS422 controller 
will be relayed...

Section 3: Operation  
3-40 013-100199-04   
 
IP ADDRESS: Enter a valid and unique IP address for use on the network to which the 
projector is currently connected. This address will overwrite any previous IP address 
such as the projector’s factory-defined default (0.0.0.0), or one that has been assigned 
by a DHCP server or other user. It takes approximately 10 seconds for the projector to 
respond at its new address. 
PORT: On some Ethernet networks, firewall restrictions may require that the port...

 Section 3: Operation 
013-100199-04  3-41. 
* Functions are only active when the Slider Lock is set to Unlocked 
 
NOTE: It is important to ensure the channels DO NOT overlap another device. 
Example: 
Good Bad 
Proj1_Base = 0  Proj1_Base = 5 
Proj2_Base = 10  Proj2_Base = 9 
Proj3_Base = 20  Proj3_Base = 11 
 
DEVICE NAME:
 This option is used to name each device; some ArtNet servers support 
querying for devices. 
DEVICE DESCRIPTION: More information that is returned when a “device query” has 
been...

Section 3: Operation  
3-42 013-100199-04   
the remaining active sensor to OFF. The projector will no longer respond to an IR 
remote keypad.  
NOTE: Protocols B – G are used for rental staging applications. 
Wired Keypad 
The wired keypad is ON by default to when connected to the rear of the projector. The 
projector will then respond to incoming commands from this port. To disable the 
wired keypad, you must use a different keypad—the built-in or an IR remote 
keypad—to select “off”. This safeguard...