Christie Digital Systems Ds+5k, Kc-8k, Dw3k-6k, Kc, Hd5k, Kc-8k, Kc, Mirage S+2-4-8k, Dlv1400-dx, 1920-dx, Matrix S+2k, 4000, Hd4k Users Manual

Section 4 
Maintenance  
 
013-100199-04  4-1 
 
 
The projector is an international regulatory agency approved product designed for safe 
and reliable operation. To assure complete safety at all times it is important to 
acknowledge the following precautions while operating the projector.  
 WARNING  
Always power down the projector using appropriate procedure 
and disconnect all power sources before cleaning or servicing. 
 WARNING  
Always remove the lens when shipping the projector. 
 WARNING  
NEVER...

Section 4: Maintenance  
4-2 013-100199-04   
• Do not operate the projector close to water, such as near a swimming pool. Do not 
operate in extremely humid environments. 
• Do not place the projector on an unstable cart, stand or table. A projector and cart 
combination should be used with care. Sudden stops, excessive force and uneven 
surfaces may cause the projector and cart combination to overturn. 
• Only use Christie-approved ceiling mount fixture, if the projector is to be ceiling 
mounted....

  Section 4: Maintenance 
013-100199-04  4-3. 
• Do not set or rest items on the power cord. Place the projector in an area where 
the projector cord cannot be abused or damaged by persons walking on it or by 
objects rolling over it. 
• Operate the projector at the specified voltage only. Do not overload power outlets 
and extension cords as this can result in fire or shock hazards. 
• The projector is equipped with a three-wire plug having a third grounding pin. 
This is a safety feature – if you are...

Section 4: Maintenance  
4-4 013-100199-04   
 
Table 4.1. Maintenance Guide 
Part Description Frequency Action 
Lens   As required  Clean the lens only when absolutely 
necessary. A small amount of dust on the 
lens has very little effect on picture quality. 
To clean: Use a soft lint-free cloth without 
any chemicals. Use only a high-quality 
coated optics cleaning fluid, which can be 
purchased from most camera supply stores. 
Apply the coated optics fluid directly onto 
the lint-free cloth until...

  Section 4: Maintenance 
013-100199-04  4-5. 
 
The IR Remote Keypad uses two AA size, 1.5V batteries (preferably alkaline). To 
install new batteries:  
1) Open the battery 
compartment at the backside 
of the keypad by placing your 
thumb in the oval depression 
and sliding the cover out about 
½ inch. See Figure 4.1. 
Remove the old batteries and 
properly discard. Wait a 
minute or two.  
2) Place the new batteries in 
the compartment, orienting the 
positive/negative of each 
battery according to...

Section 4: Maintenance  
4-6 013-100199-04   
Table 4.2. Lamp/Filter Replacement Kits 
Projector Model Model Number Lamp Type 
(Watts) 
Lamp/Filter Kit Required 
38-DSP102-04 03-000832-01P Mirage S+2K 
38-DSP102-54 03-000832-51P 
38-DSP102-06 03-000832-01P Matrix S+2K 
38-DSP102-56 03-000832-51P 
38-DSP102-05 03-000832-01P DLV1400-DX 
38-DSP102-55 03-000832-51P 
DLV1920-DX 104-017101-01 500W 
003-120118-01 
38-DSP104-05/-08 03-000833-01P Christie DS+5K/Kc 
38-DSP104-55/-58 03-000833-51P 
Christie HD5K/Kc...

  Section 4: Maintenance 
013-100199-04  4-7. 
1. TURN THE LAMP OFF 
Press 
 (power) to turn the lamp off. Allow the cooling fans to stop 
automatically (within approximately five minutes) before proceeding with Step 2. 
This wait period is also required to allow the lamp to sufficiently cool before 
handling. 
2. UNPLUG THE PROJECTOR 
When the cooling fans have stopped, turn the projector’s main switch off, and 
unplug. 
 WARNING  
Always power down and unplug the projector prior to 
servicing. Allow...

Section 4: Maintenance  
4-8 013-100199-04   
5. REMOVE THE LAMP MODULE 
Firmly grasp the lamp by its housing only and pull it straight out (lamp slides 
along guides) until it is free. See Figure 4.4. Discard the lamp using safe 
disposal/recycling practices.
 
 
 
 
6. INSERT THE NEW LAMP MODULE 
Align the new lamp with the top and bottom guides on the left side of the lamp 
compartment (see Figure 4.5). Slide the lamp all the way in – a slightly harder 
push may be required right at the end to ensure...

  Section 4: Maintenance 
013-100199-04  4-9. 
NOTE: If you can’t turn the lamp lock into position, it is likely the lamp is not 
fully inserted. In this case, partially remove the lamp and try pushing it back in 
again. Then, try switching the lock lever to the “lock” position. 
 
8. REPLACE THE LAMP DOOR 
Replace the lamp door and secure it with the two (2) screws removed in Step 2. 
 IMPORTANT  
The lamp module is calibrated for maximum performance 
and brightness in this projector. Do not attempt to...

Section 4: Maintenance  
4-10 013-100199-04   
The two filters located at the front 
and left side of the projector should 
be replaced whenever the lamp is 
replaced. If you are working in an 
extremely dusty environment you 
may want to replace the filters sooner. 
Use the filters provided in the 
Christie approved Lamp and Filter 
Kit for your specific projector model. 
1. TURN OFF THE PROJECTOR, 
COOL and UNPLUG 
Before removing or installing a filter, turn off the projector and allow it to cool for...