Christie Digital Systems Ds+5k, Kc-8k, Dw3k-6k, Kc, Hd5k, Kc-8k, Kc, Mirage S+2-4-8k, Dlv1400-dx, 1920-dx, Matrix S+2k, 4000, Hd4k Users Manual

 Section 3: Operation 
013-100199-04  3-63. 
 
Figure 3.16. Match Zones to Center Color Temperature 
Repeat the color adjustment of sides and corners for each edge of the screen that does 
not yet match the center (note that each corner is adjustable in either of its two 
adjacent “side” menus). When done, all areas of a given screen should match. Repeat 
Steps 
2a & 2b for all remaining screens. 
Step 3: Adjust Light Output in Eight Zones 
3a) For each screen, compare the light output of each edge and...

Section 3: Operation  
3-64 013-100199-04   
Cancelling Brightness Uniformity 
If you do not want to use or apply Brightness Uniformity settings, delete the 
checkmark from the “Uniformity Enable” checkbox at the top of the Brightness 
Uniformity menu. 
Christie Edge Blending is an innovative set of software functions that can quickly and 
easily blend white levels along the edges of multiple adjacent projected images to 
create a single seamless larger image. 
What is a Blend? 
In simple terms, a blend...

 Section 3: Operation 
013-100199-04  3-65. 
• Blend Width determines how much area is used for blending along an overlapping 
edge. Slide bar values represent the number of eight-pixel steps used for the 
blend. For example, a setting of “eight” creates a blended edge 24 pixels wide. A 
setting of “0” signifies no blending. For best results in most applications, use a 
blend width of 16-48 steps (128-384 pixels). 
Ranges: 0-80 horizontal, 0-60 vertical. 
• 
Blend Shape determines the rate of 
roll-off...

Section 3: Operation  
3-66 013-100199-04   
• Show Blending Overlap turns your 
defined blend width area to solid gray so 
that, if needed, simply overlapping the 
gray bars can seamlessly align two 
adjacent images. Toggle the Show 
Blending Overlap off to reactivate the 
blend effect.  
• NOTE: Blending Overlap appears as 
Reserved when ChristieTWIST is 
installed. 
Other Functions  
For convenience, the Edge Blending 
submenu also includes related options for 
enabling a specific color and/or test...

 Section 3: Operation 
013-100199-04  3-67. 
4. SET BLEND WIDTH: On one projector, increase the Blend Width for an overlapping 
edge (for example, if the projector’s image is on left, its right edge overlaps the 
adjacent image—adjust Right Blend Width). Use the same setting on the second 
projector for this shared edge. 
5. Re-adjust width (both projectors) until the overly bright band at the midpoint of the 
overlapping blends disappears or just changes to very light gray. For the shared 
edge, use the...

Section 3: Operation  
3-68 013-100199-04   
 
3.   Working with one projector at a time, use the center brightness slide bar to adjust 
the center brightness (brightness of the non-blended region) so that the center 
intensity matches that of the brightest blended region (the center of all images 
when blending a 2 x 2 display is the target area). 
4.   Use the following three color slide bars, Black Red Level, Black Green Level and 
Black Blue Level, so the black hue of each projector matches. 
5....

 Section 3: Operation 
013-100199-04  3-69. 
Repeat for remaining networked projectors as desired. Keep in mind that multiple 
units can be controlled from one PC, but each unit will be in its own ChristieNET 
interface (web browser) at the PC. Likewise, you can make up to five separate web 
locations to a single projector. 
The default login provides access to security settings, where you can define other 
users with the same or fewer rights. Use “unlimited” rights for most applications. For 
all...

Section 3: Operation  
3-70 013-100199-04   
No Signal 
The message No signal occurs when there is no source signal detected at the 
selected input—both HSYNC and VSYNC are inactive and the screen background is 
black. Connect or correct the signal, or try another input. 
Bad Sync 
The message Bad Sync occurs when HSYNC or VSYNC are active but the signal 
cannot be displayed. Such a condition occurs when only one of the two sync signals is 
present or when either sync signal is unstable or is the wrong...

 Section 3: Operation 
013-100199-04  3-71. 
The Status LED Codes 
If the status code display on the back of the projector shows one of the following 
values, you have encountered a likely system error requiring the attention of a 
qualified service technician (see System Warnings and System Errors, above). 
Acknowledge and clear the error with 
Exit Exit from presentation level, or try 
resetting the projector by powering it off and on again, cooling when necessary. 
Consult Table 3.5 and contact your...

Section 3: Operation  
3-72 013-100199-04   
88  Red modular Formatter communication failure  89  Green modular Formatter communication failure 8A  Blue modular Formatter communication failure 93  Modular formatter architecture error 94  Modular formatter DMD mismatch 95  Modular formatter sequence mismatch MISCELLANEOUS A0  Unable to program the optional module  A1  Unable to power the optional module  A2  Unable to program the Dual Slot Backplane Module (DSBP) A3  Unable to program the optional Post...