Christie Christi Eprojector Mirage S+22k J Technical Manual

J Series Serial Commands Technical Reference Information61 of 90020-100796-01 Rev. 1 (10-2011)
(NET) Network Setup con’t
HOST Set the host name.
MAC0 Gets the MAC address of the first ethernet controller.
PORT Set the PORT number.
SUB0 Set the network subnet mask for the first ethernet controller.
EXAMPLES:
(NET+ETH0 192.168.1.35) - Set new IP address on the first ethernet controller. 
(NET+GATE 192.168.0.1) - Set the gateway. 
(NET+SUB0 255.255.255.0) - Set the subnet mask on the first ethernet...

62 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(NRD) General Noise Reduction con’t
EXAMPLE:
(NRD 32) - Set the noise reduction to mid point for main video. 
(NTR) NETWORK ROUTING 
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Set routing for ASCII messages. 
SUBCODE

DESCRIPTION OF USE
Used to enable or disable daisy chaining.
0 = RS232, RS422 & Ethernet communications are all separate 
from one another
1 =...

J Series Serial Commands Technical Reference Information63 of 90020-100796-01 Rev. 1 (10-2011)
(OST) OSD TRANSPARENCY 
CONTROL GROUP: Preference     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Enable or Disable on screen display transparency. 
SUBCODE

DESCRIPTION OF USE
Enable or disable OSD transparency.
EXAMPLE:
(OST 1) - Enable OSD transparency. 
(PBC) PIP BORDER COLOR 
CONTROL GROUP: Preference     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
This control lets...

64 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(PDT) PEAK DETECTOR 
CONTROL GROUP: Unsaved     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Enables or disables the peak detector test mode. This is used to aid in setup of input levels. For each color, pixel 
values very near black will be displayed black, pixel values very near peak level will be displayed full on. All oth-
ers will be displayed in mid level grey. Input levels for each...

J Series Serial Commands Technical Reference Information65 of 90020-100796-01 Rev. 1 (10-2011)
(PIP) PICTURE IN PICTURE 
CONTROL GROUP: Preference     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
This control enables or disables Picture in Picture (PIP) mode. When this control is enabled for the first time, the 
first valid video signal starting at slot 1 input 1 is routed to the PIP window. If no signals are present, the first 
available slot/input combination is selected. 
PIP and...

66 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(PLK) PIP User Lockouts con’t
EXAMPLES:
(PLK L*) - Locks all codes/subcodes in the system (except the PLK and PWR control, which are unlockable) 
(PLK U*) - Unlocks all codes/subcodes in the system, regardless of which method was used to lock them 
(PLK LSIN*) - Locks all subcodes within the SIN control 
(PLK USIN+PIIP) - Following the previous example, this unlocks SIN+PIIP, leaving all other SIN subcodes...

J Series Serial Commands Technical Reference Information67 of 90020-100796-01 Rev. 1 (10-2011)
(PPA) POSITION PRESET ASPECT 
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
When enabled, this control ensures that during auto setup for any source, its aspect ratio is maintained when its 
default size is calculated. This is similar to cases where a stretch is defined for a source in the lookup table. If dis-
abled and no stretch is defined, the source is...

68 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(PRT) SERIAL PORT
CONTROL GROUP: Preference    SUBCLASS: Power Down           ACCESS LEVEL: Status
DESCRIPTION
Get a list of serial ports available on the device.
SUBCODE

DESCRIPTION OF USE
Read serial ports.
EXAMPLE:
(PRT?1) - Get list of ports. 
(PTL) SERIAL PROTOCOL
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Advanced
DESCRIPTION
Set the protocol for a serial communications...

J Series Serial Commands Technical Reference Information69 of 90020-100796-01 Rev. 1 (10-2011)
(PWR) POWER 
CONTROL GROUP: Unsaved     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Change the power state of the projector.
Possible values:
0   = Power-Off (to Standby mode)
1   = Power-On (to Lamps On mode)
10 = Cooldown lamp is cooling down. Controlled by lamp (read-only)
11 = Warmup lamp is warming up. Controlled by lamp (read-only)
20 = AutoShutdown mode 1 (read only)
21 =...

70 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(PXT) PIXEL TRACKING 
CONTROL GROUP: Input     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Pixel Tracking adjusts the position of the pixel sampling clock to match the input signal. It can only be set on 
Analog input cards. If adjusted incorrectly, flickering or vertical bars of noise appear across the image. Adjust 
Pixel Tracking so that the noise either disappears or fills the image. If...