Christie Christi Eprojector Mirage S+22k J Technical Manual

J Series Serial Commands Technical Reference Information11 of 90020-100796-01 Rev. 1 (10-2011)
 (ILV) ILS Settings Valid  (MDE) Serial Mode  (PMT) Picture Mute
 (INM) Channel ‘In Menu’  (MFT) Menu Font  (PNG) Ping
 (ITG) Test Pattern Grey  (MLK) Channel Memory Lock  (PPA) Position Preset Aspect
 (ITP) Internal Test Pattern  (MNR) Mosquito Noise Reduction  (PPP) PIP Position Preset
 (KEN) Keypad IR Sensor Disable  (MNU) Menu Settings and Config-
uration (PPS) PIP Swap
 (KEY) Key Mode Emulation  (MSH) Menu...

12 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
 (SPS) Splash Screen  (TDM) 3D Mode  (TTM) THIC Transmitter Mode 
Configuration
 (SPT) Split Screen  (TDN) Invert 3D Input  (TXE) Texture Enhancement
 (SST) System Status  (TDO) 3D Sync Out  (UID) User ID
 (STD) Video Standard  (TDT) 3D Test Pattern  (VBL) Video Black Input
 (SZP) Size Presets  (TED) Twin HDMI EDID type 
selection (VRT) Vertical Position
 (TBL) Top Blanking  (TIL) Tiling Control  (VST) Vertical...

J Series Serial Commands Technical Reference Information13 of 90020-100796-01 Rev. 1 (10-2011)
DETAILED SERIAL COMMAND DESCRIPTIONS
(ACE) AUTO COLOR ENABLE 
CONTROL GROUP: Preference     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
Automatically select Color Enable based on the control being adjusted. If enabled, this control allows the projec-
tor to automatically change the color enable control when the user is using the OSD interface to adjust controls 
such as input levels, odd...

14 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(ACT) Active Window con’t
EXAMPLES:
(ACT?) - Returns the active window for main video. 
(ACT+PIIP?) - Returns the active window for PIP video. 
(ACT+IN12?) - Returns the active window for slot 1 input 2. 
(ADR) ADDRESS 
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
Set/Query Device Address on ASCII Protocol network. Required only for RS232 connections that are...

J Series Serial Commands Technical Reference Information15 of 90020-100796-01 Rev. 1 (10-2011)
(AIC) AUTO INPUT CYCLING 
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Operator
DESCRIPTION
When enabled, the system will continually search for the next valid signal when no signal is present or when loss 
of sync occurs on the current user selected input. In the case of multiple signals to choose from, the order is based 
on slot, followed by inputs on that slot. 
SUBCODE...

16 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(ALT) Active Loop-Through con’t
EXAMPLES:
(ALT 1) - Enable Standby active loop-through. 
(ALT 0) - Disable Standby active loop-through.
(ALT?) - Get the current Standby active loop-through setting.
(APR) APERTURE
CONTROL GROUP: Preference    SUBCLASS: Power Up       ACCESS LEVEL: Operator
DESCRIPTION
The Optical Aperture control sets the diameter of the light path. It is used to trade off between contrast and...

J Series Serial Commands Technical Reference Information17 of 90020-100796-01 Rev. 1 (10-2011)
(APW) Auto Power Up con’t
EXAMPLES:
(APW 0) - Projector will remain in Standby Mode until the user presses the power key. 
(APW 1) - Projector will auto power up when A/C power is switched on if it was in a powered on state (i.e. not in 
standby mode) when the A/C power was powered off in the previous power cycle.
(ARO) ASPECT RATIO OVERLAY 
CONTROL GROUP: Unsaved     SUBCLASS: Power Up           ACCESS LEVEL:...

18 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(ASR) AUTO CHANNEL SELECT 
CONTROL GROUP: Channel     SUBCLASS: Power Up           ACCESS LEVEL: Operator
DESCRIPTION
The Auto Channel Select option allows the projector to select the channel memory best suited to the input signal. 
If the current channel does not allow Auto Channel Select, the projector will not attempt to select a new channel 
when the signal changes. If the current channel does allow Auto...

J Series Serial Commands Technical Reference Information19 of 90020-100796-01 Rev. 1 (10-2011)
(ASU) Auto Setup con’t
PIIP or SECD  Perform a standard auto setup on the picture in picture or Second-
ary video.
FRZE Hides temporary image artifacts that may appear during the auto 
setup procedure.
EXAMPLES:
(ASU) - Perform standard auto setup on main video. 
(ASU+FRZE 1) - Freeze image during auto setup.
(ASU+FRZE 0) - Disable image freezing during auto setup.
(ASU+MAIN) - Perform standard auto setup on...

20 of 90J Series Serial Commands Technical Reference Information020-100796-01 Rev. 1 (10-2011)
(BDR) BAUD RATE  
CONTROL GROUP: Preference     SUBCLASS: Power Down           ACCESS LEVEL: Advanced
DESCRIPTION
Set the baud rate for a serial communications port. For RS232 IN and RS232 OUT, the default is 115200. For 
RS422, the default is 19200. The default communications settings for all ports is 8 data bits, no parity. Valid baud 
rates, with the values to select them, are: 
0 = 1200 
1 = 2400 
2 = 9600...