Casio Qt6000 Service Manual

— 39 —
[ 14 ] Remote Cust DISP test
[Function]
This test will check whether REMOTE DISP can be displayed.
Make sure to connect REMOTE DISP to COM3.
In case of one time check only, the test can be ended by the judgment (OK or NG) of the operator.
Pastel green (white plus green) appears as the backlight, which turns off upon the end of the test.
* When changing the baud rate, make sure to change the REMOTE DISP setting.
[Operation]
Press [OK] key or [NG] key to end the test when performing one time check....

— 40 —
[ 15 ] External printer print test
[Function]
This test will check the print test for the RS232C I/F printer.
Connect the printer to the COM which is to be tested.
[Operation]
Operation :  x1 x2 x3 n 0 3 d ST
X1: Print test pattern (0 = A pattern, 1 = B pattern)
X2: Port selection (1 = COM1, 2 = COM2, 3 = COM3, 4 = COM4, 5 = COM5, 6 = COM6)
X3: Baud rate selection (1 = 4800 bps, 2 = 9600 bps, 3 = 19.2 kbps)
n: 0 = One time check (can be omitted)
not 0 = Continuous check (To stop the test, press...

— 41 —
[ 16 ] RS232C PORT test
[Function]
This is the RS232C test.
The loop back test for RS232C port is performed by making the connection shown in the figure.
Refer to [ 17 ] RS232C PORT batch test the figure for RS232C port connection.
[Operation]
Operation : x n 0 4 d ST
x: Baud rate selection
0 = 2400 bps, 1 = 4800 bps, 2 = 9600 bps, 3 = 19.2 kbps, 7 = 115 kbps (COM 1 only)
n: 0 = One time check (can be omitted)
not 0 = Continuous check (To stop the test, press ESC key)
d: Port selection
1 = COM1, 2...

— 42 —
[ 17 ] RS232C PORT batch test
[Function]
This is the RS232C port batch test.
The loop back test for RS232C port is performed by making the connection shown in the figure.
The loop back test is performed from COM1 to COM 6 by the following setting by one time check.
When performing this test, fix loop back connectors to all COM ports.
[Operation]
Operation : 4 0 ST
Baud rate: COM1: 115 kbps, COM 2 – 6 : 9600 bps
Check time: one time
[LCD]
COM BATCH    40 
RTS1=1 
 CTS1=1 OK
DTR1=1 
 DSR1=1 OK...

— 43 —
[ 18 ] Ethernet test
[Function]
This test will check the counter-communication of Ethernet.
Always make the receive ECR in the wait mode first and then send data from the send ECR.
The counter of the number of successful/failed communication to the LCD is displayed after the
communication normally starts. It is printed after the test.
* Send/receive data
SIDLRCDIDLEN DATA 00h~FFh, 00h~FBh
508 byte
[LCD]
[PRINT]
ETHERNET m0a51
TCP MODE
OK xxxx  NG xxxx
END   m0a51
ETHERNET m0a51
TCP MODE
OK xxxx...

— 44 —
[ 19 ] MAC Address SET
[Function]
This test will write the MAC address.
[Operation]
* Once an ID is set, make sure to perform the test using this ID. When changing the ID, turn the power
on again.
x0951ST
[LCD]
[PRINT]
MAC ADDRESS  x0951
xxxxxx
END   x0951
MAC ADDRESS  x0951
xxxxxx
END   x0951
x : Writing the address
0: Writes a consecutive address based on MAC address in CF
* Example
The following ASCII data is written in MACADR.TXT in CF.
FF8048FF9800
The test writes FF8048FF9801, which is 1+...

— 45 —
[ 20 ] Wireless LAN test
[Function]
This test will check the counter-communication of wireless LAN.
Always make the receive ECR in the wait mode first and then send data from the send ECR.
The counter of the number of successful/failed communication to the LCD is displayed after the
communication normally starts. It is printed after the test.
* Send/receive data
SIDLRCDIDLEN DATA 00h~FFh, 00h~FBh
508 byte
[LCD]
[PRINT]
WIRELESS LAN  m0a52
TCP MODE
OK xxxx  NG xxxx
END   m0a52
WIRELESS LAN  m0a52...

— 46 —
[ 21 ] Time setting / [ 22 ] Time display
[Function]
This sets the time and date.
When setting the time, the time and date will be displayed without inputting the fixed value.
[Operation]
* Date and time setting
Operation : x1 x2 x3 x4 x5 x6 0 a 7 0 ST
a: 0: time setting x1/x2: time, x3/x4: minutes, x5/x6: second
1: time setting x1/x2: year, x3/x4: month, x5/x6: day
The test will be done one time.
* Date and time display
Operation : 7 0 ST
To stop the operation, press ESC key.
[LCD]
Each data will...

— 47 —
[ 24 ] Buzzer test
[Function]
This test will check the buzzer function.
Ring the one-shot buzzer.
[Operation]
Operation :  n 0 9 2 ST
n: 0 = One time check (can be omitted)
not 0 = Continuous check (To stop the test, press ESC key)
[LCD]
[PRINT]
BUZZ   n092
END   n092
BUZZ   n092
END   n092
[ 25 ] OBR test
[Function]
This is a scanner test. The test enters the wait mode for the scanner input, and waits only for scanner.
The test determines the result between OK and NG by comparing the fixed data...

— 48 —
[ 26 ] MCR test
[Function]
This is a card reader (MCR) test. The test enters the wait mode for only MCR input.
The test judges the result between OK and NG by the comparison between already set data and
read data.
[Operation]
Operation :  9 6 ST
    Press [ESC] key to end the test manually.
[LCD]
MCR1 indicates track 1 while MCR2 indicates track 2 in the display.
* Normally ended (both track 1 and 2)
MCR   96
MCR1   OK
MCR2   OK
END   96
MCR2 ERR **************************
**************
MCR1 ERR...