Casio Exilim EX ZR100 User Manual

							21Quick Start Basics
1.Press [ON/OFF] (Power) to turn off 
the camera and then open the 
battery cover.
Slide the battery cover slider towards 
OPEN and then open it as indicated by 
the arrows in the illustration.
2.Load a memory card.
Positioning the memory card so its front 
is facing upwards (towards the monitor 
screen side of the camera), slide it into 
the card slot all the way in until you hear 
it click securely into place.
3.Close the battery cover.
Close the battery cover and then shift the 
slider towards LOCK.
• For information about how to replace 
the memory card, see page 177.
IMPORTANT!
• Never insert anything besides a supported memory card (page 20) into the memory 
card slot.
• Should water or any foreign object ever get into the card slot, immediately turn off 
the camera, remove the battery, and contact your retailer or nearest CASIO 
authorized service center.
To load a memory card
Front BackFront
Downloaded From camera-usermanual.com Casio Manuals 
						

							22Quick Start Basics
You need to format a new memory card before using it for the first time.
1.Turn on the camera and press [MENU].
2.On the “Set Up” tab, select “Format” and then press [6].
3.Use [8] and [2] to select “Format” and then press [SET].
IMPORTANT!
• Formatting a memory card that already has snapshots or other files on it, will delete 
its contents. Normally you do not need to format a memory card again. However, if 
storing to a card has slowed down or if you notice any other abnormality, re-format 
the card.
• Be sure to use the camera to format a memory card. Formatting a memory card on 
a computer and then using it in the camera can slow down data processing by the 
camera. In the case of an SD, SDHC, or SDXC memory card, formatting on a 
computer can result in non-conformity with the SD format, causing problems with 
compatibility, operation, etc.
To format (initialize) a new memory card
Downloaded From camera-usermanual.com Casio Manuals 
						

							23Quick Start Basics
• Take care to ensure that nothing is restricting or 
coming into contact with the lens as it extends. 
Holding the lens with your hand so it cannot extend 
creates the risk of malfunction.
•Pressing [p] (PLAY) while in the REC mode 
switches to the PLAY mode. The lens retracts about 
10 seconds after switching modes.
• The Sleep function or Auto Power Off (pages 161, 162) will turn off power 
automatically if you do not perform any operation for a preset amount of time.
Press [ON/OFF] (Power).
• You can configure the camera so power does not turn on when you press [r] 
(REC) or [p] (PLAY). You also can configure the camera to turn off when you 
press [r] (REC) or [p] (PLAY) (page 162).
Turning the Camera On and Off
To turn power on
To turn on 
power and enter 
the REC modePress [ON/OFF] (Power) or 
[r] (REC).
• The back lamp will light green 
momentarily and the lens will extend 
out of the camera (page 25).
To turn on 
power and enter 
the PLAY modePress [p] (PLAY).
• The back lamp will light green 
momentarily and an image currently 
stored in camera memory will 
appear on the monitor screen 
(page 28).
To turn off the camera
Back lamp
[p] (PLAY) [r] (REC) [ON/OFF] (Power)
Downloaded From camera-usermanual.com Casio Manuals 
						

							24Quick Start Basics
Your images will not come out 
clearly if you move the camera 
when you press the shutter 
button. When pressing the 
shutter button, be sure to hold 
the camera as shown in the 
illustration, and keep it still by 
pressing your arms firmly 
against your sides as you shoot.
Holding the camera still, 
carefully press the shutter button 
and take care to avoid all 
movement as the shutter 
releases and for a few moments after it releases. This is especially important when 
available lighting is low, which slows down the shutter speed.
NOTE
• Take care that your fingers and the strap do not 
cover any of the areas indicated in the illustration.
• To protect against accidentally dropping the 
camera, attach the wrist strap and make sure it is 
around your fingers or wrist while you are operating 
the camera.
• Never swing the camera around by its strap.
• The supplied strap is intended for use with this 
camera only. Never use it for any other purpose.
• When the “Auto Rotate” setting is turned on, the 
camera will detect whether it is being held vertically 
or horizontally when a snapshot image is shot. 
When you display an image shot with the camera held vertically, the image is 
rotated automatically 90 degrees when displayed on the monitor screen (page 
156).
IMPORTANT!
• Take care to ensure that your fingers are not blocking or 
are not too close to the flash. Fingers can cause unwanted 
shadows when using the flash.
Holding the Camera Correctly
Horizontal Vertical
Hold the camera so the flash is above the lens.
Front lamp
Lens Flash
Downloaded From camera-usermanual.com Casio Manuals 
						

							25Quick Start Basics
You can select one of two auto recording modes (Auto or Premium Auto) according to 
your digital imaging needs.
1.Press [r] (REC) to turn on the camera.
The camera will enter the REC mode.
2.Set the mode dial to t (Auto) or Ÿ (Premium Auto) to select Auto 
recording mode.
To shoot a snapshot
Selecting an Auto Recording Mode
 AutoThis is the standard Auto recording mode.
• It provides faster operation than Premium Auto recording.
 Premium AutoWith Premium Auto recording, the camera automatically 
determines whether you are shooting a subject or scenery, 
and other conditions. Premium Auto recording delivers higher 
image quality than standard Auto recording.
• Premium Auto recording takes longer to process image data 
after it is shot than Auto recording.
• It also requires more power (and runs down the battery 
quicker) than Auto.
R
Ÿ
Auto recording mode icon
Remaining Snapshot Memory
Capacity (page 191)
Shutter button
[r] (REC) Mode dial Monitor screen
Downloaded From camera-usermanual.com Casio Manuals 
						

							26Quick Start Basics
1.Point the camera at the subject.
If you are using Premium Auto, text will appear in the 
lower right corner of the monitor screen describing the 
type of shot the camera has detected.
• You can zoom the image, if you want.
To shoot a snapshot
2.Half-press the shutter button to 
focus the image.
When focus is complete, the camera 
will beep, the back lamp will light green, 
and the focus frame will turn green.
When you half-press the shutter button, the 
camera automatically adjusts exposure and 
focuses on the subject it is currently pointed at. 
Mastering how much pressure is required for a 
half-press and a full-press of the shutter button 
is an important technique for good-looking 
images.
3.Continuing to keep the camera still, 
press the shutter button the rest of 
the way down.
This records the snapshot.
Appears when the 
camera detects it is 
stationary on a tripod.
w Wide Anglez TelephotoZoom controller
Focus frame
Back lamp
Half-press
Press lightly 
until the 
button stops.
Beep, beep (Image is in focus.)
Full-press
Snap (Image is recorded.)
Downloaded From camera-usermanual.com Casio Manuals 
						

							27Quick Start Basics
.If the image does not focus...
If the focus frame stays red and the back lamp is flashing green, it means that the 
image is not in focus (because the subject is too close, etc.). Re-point the camera at 
the subject and try to focus again.
.Shooting with Auto
If the subject is not in the center of the frame...
“Focus lock” (page 86) is the name of a technique you can use when you want to 
shoot an image in which the subject to be focused on is not within the focus frame in 
the center of the screen.
To track the movement of a moving subject
Half-press the shutter button to follow and focus automatically on a moving subject. 
See “Ë Tracking” (page 89) for more information.
.Shooting with Premium Auto
• In addition to shutter speed, aperture, and ISO sensitivity, the camera 
automatically executes the following operation as required when shooting with 
Premium Auto.
– Auto Focus is normally performed until you half-press the shutter button.
– Intelligent AF (Page 89)
– Face Detection (Page 90)
• Shooting with Premium Auto can cause vibration and noise to occur due to lens 
operation. This does not indicate malfunction.
• When Shooting with Premium Auto, the message “Processing Premium Auto. 
Please wait...” may appear on the monitor screen. If you feel the camera is taking 
too long to process data, try shooting with standard Auto instead.
• In some cases, Premium Auto may not be able to interpret the shooting 
environment correctly. If this happens, shoot with standard Auto.
Recording a Movie
Press [0] (Movie) to start movie recording. Press [0] (Movie) 
again to stop movie recording. See the following pages for 
details.
Standard movie (STD movie): page 61
High-definition movie (FHD movie): page 64
High speed movie (HS movie): page 64
[0] (Movie)
Downloaded From camera-usermanual.com Casio Manuals 
						

							28Quick Start Basics
Use the following procedure to view snapshots on the camera’s monitor screen.
• For information about how to play back movies, see page 99.
• For information about images recorded using continuous shutter (CS), see page 
101.
1.Press [p] (PLAY) to enter the 
PLAY mode.
• This will display one of the snapshots 
currently stored in memory.
• Information about the displayed 
snapshot also is included (page 12).
• You also can clear the information to 
view only the snapshot (page 166).
• You can zoom in on the image by 
sliding the zoom controller towards z (page 106). If you are recording a 
snapshot that is very important to you, it is recommended that you zoom the 
image and check its details after recording it.
2.Use [4] and [6] to scroll between images.
• Holding down either button scrolls at high speed.
NOTE
• Half-pressing the shutter button while in the PLAY mode or while a menu screen is 
displayed will switch directly to the REC mode.
Viewing Snapshots
[p] (PLAY)
[6]
[6]
[4]
[4]
Downloaded From camera-usermanual.com Casio Manuals 
						

							29Quick Start Basics
If memory becomes full, you can delete snapshots and movies you no longer need in 
order to free up storage and record more images.
IMPORTANT!
• Remember that a file (image) delete operation cannot be undone.
• For information about images recorded using continuous shutter (CS), see page 
102.
1.Press [p] (PLAY) to enter the PLAY mode and then 
press [2] ( ).
2.Use [4] and [6] to scroll through the files until the one 
you want to delete is displayed.
3.Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
• If a CS group (page 101) is displayed when you perform the above procedure, 
all of the images in the currently displayed CS group will be deleted.
Deleting Snapshots and Movies
To delete a single file
Downloaded From camera-usermanual.com Casio Manuals 
						

							30Quick Start Basics
1.Press [p] (PLAY) to enter the PLAY mode and then press [2] ( ).
2.Use [8] and [2] to select “Delete Files” and then press [SET].
• This displays a file selection screen.
3.Use [8], [2], [4], and [6] to move the selection boundary to the file 
you want to delete, and then press [SET].
• This will select the check box of the currently selected file.
4.Repeat step 3 to select other files, if you want. After you are finished 
selecting files, press [MENU].
5.Use [8] and [2] to select “Yes” and then press [SET].
• This deletes the files you selected.
• To cancel the delete operation, select “No” in step 5 and then press [SET].
1.Press [p] (PLAY) to enter the PLAY mode and then press [2] ( ).
2.Use [8] and [2] to select “Delete All Files” and then press [SET].
3.Use [8] and [2] to select “Yes” and then press [SET] to delete all files.
This will cause the message “There are no files” to appear.
To delete specific files
To delete all files
Downloaded From camera-usermanual.com Casio Manuals