Canon scanner imageFORMULA DRM1060 User Manual

							31
What to do when a double feed is 
detected
When not using the double feed detection ignore function
If a document double feed is detected during scanning, document 
feeding stops when the double fed documents are ejected. When this 
happens, the following error code is displayed in the Job No. Indicator 
of the operating panel.
Also, a message screen is displayed to notify you that a double feed 
has been detected. For example, the following screen is displayed in 
CapturePerfect.
When this happens, stop the scanning in the application and then 
scan the documents again.
When using the double feed detection ignore function
If a document double feed is detected during scanning, document 
feeding stops when the double fed documents are ejected. The 
following error code is displayed in the Job No. Indicator of the 
operating panel, and the DFR button lights.Also, the [Rapid Recovery System] screen appears to enable you to 
specify whether to continue scanning.
Double feed detection error code
Double feed detection error code 
						

							32
Detecting Skewed Documents
This scanner includes a function that can detect when a document has 
been fed at a slant. When this function is used, the scanner will stop a 
scanning operation automatically when it detects a skewed document 
that exceeds a fixed angle, thereby preventing damage to the 
document.
This function is useful for documents that are 148 mm (5.9) or larger 
in width.
To use the skew detection function, open the scanner driver settings 
screen and enable the skew detection function beforehand.
Setting procedure
1Open the scanner driver settings screen. (See p. 50)
2Click the [Feeding] tab.
3Select the [Skew Detection] check box.
4Click the [OK] button to close the settings screen.
5Place the document as described in “Placing 
Documents” (see p. 25).
IMPORTANT
When this function is enabled, small documents and documents 
that have been placed to the left or right of the center of the feed 
inlet may be detected as skewed, and the scanning operation 
may stop. Place documents in the center of the feed inlet, or 
disable the skew detection function. Buttons of 
[Rapid Recovery 
System] ScreenButtons of 
Operating 
PanelDescription
[SAVE & 
CONTINUE]DFR buttonSaves the preview image as a 
scanned image and scans the 
rest of the document.
[STOP] Stop buttonDiscards the preview image and 
stops scanning.
[DISCARD & 
CONTINUE]Start buttonDiscards the preview image and 
continues scanning. Place the 
double fed document again 
before clicking this button. 
						

							33
When a skewed document is detected
Feeding automatically stops when a skewed document is detected 
during scanning. The following error code is also displayed in the Job 
No. Indicator of the operating panel.
Also, a message screen is displayed to notify you that a skewed 
document has been detected.
Hint
If [Rapid recovery system] is enabled in the [Others] tab of the 
scanner driver settings screen, the following screen appears instead 
of the above message screen. In such cases, reload the document 
and click [Yes] to continue scanning.
Detecting Staples and Feed Errors
This scanner includes a function that can detect documents that are 
stapled together and a function that can detect feed errors.
When these functions are used, the scanner will stop a scanning 
operation automatically when a stapled document is fed or a feed error 
occurs, thereby preventing damage to the document.
The feed error detection function is useful for documents that are 
148 mm (5.9) or larger in width.
To use the staple detection or feed error detection function, open the 
scanner driver settings screen and enable the staple detection or feed 
error detection function beforehand.
Setting procedure
1Start CapturePerfect. (See p. 48)
2Open the scanner driver settings screen. (See p. 50)
3Click the [Feeding] tab.
4Select the [Staple Detection] or [Paper feed error 
detection] check box.
Skew detection error code 
						

							34
5Click the [OK] button and close the settings screen.
6Place the document as described in “Placing 
Documents” (see p. 25).
When a stapled document or feed error is 
detected
Feeding automatically stops when a stapled document or feed error is 
detected during scanning. The following error code is also displayed 
in the Job No. Indicator of the operating panel.
A notification that a feed error was detected also appears on the 
screen.
Hint
 When [Rapid recovery system] is enabled in the [Others] tab of the 
scanner driver settings screen, the following screen appears 
instead of the above message screen. In such cases, place the 
document again, and then click [Yes] to resume scanning.
 When sensors at both sides of the feed inlet detect the bent corner 
of a stapled document, an error message appears and feeding 
stops. 
Staple detection may not operate properly in the following cases 
where bending does not occur in documents.
– The document is stapled at two or more corners.
– The document is size smaller than STMT/A5.
Staple or feed error detection error code 
						

							35
Scanning methods
Scanning with CaptureOnTouch
What is CaptureOnTouch?
CaptureOnTouch is a scanning application that allows you to scan a 
document with a simple operation by following the instructions on the 
screen.
CaptureOnTouch is provided with multiple scanning methods that can 
be selected according to the purpose and application.
Scan First
Scan a document and then select the output method. This method 
allows you to easily scan a document by just following the instructions 
on the screen.
Select Scan Job
Register scanning settings from the scanning conditions to the output 
method as jobs, and then scan a document by just selecting the job 
that suits your purpose. This method is convenient when you want to 
repeat scanning using a set procedure.
Operating the scanner with the operating panel buttons
You can start scanning by selecting a job from the scanner’s operating 
panel.
Format for saving image files
Excluding times when [Print] is selected as the output method, you 
can specify any of the following file formats for scanned images.

 TIFF format
 JPEG format
 BMP format
 PPTX format (file format for Microsoft PowerPoint 2007 and later)
Starting and Exiting CaptureOnTouch 
By default, CaptureOnTouch becomes resident in the system when 
you start your computer.
Double-click   (CaptureOnTouch icon) in the taskbar to start 
CaptureOnTouch and display the main window.
Hint
 You can also start CaptureOnTouch from the Start menu. Click 
[Start] – [All Programs] – [Canon DR-M1060] – [DR-M1060 
CaptureOnTouch].
 When [Make CaptureOnTouch resident] is turned on by using the 
[Basic settings] tab on the [Environmental settings], this shortens 
the time from pressing the scanner start button to the start of 
scanning. For details, see “Environmental Settings” on p. 45.
Save to folder
Save the file to a specified folder.Print
Print with a specified 
printer.
(Network)
Send to application
Open the scanned image file 
in a specified application.
Attach to E-mail
Start the e-mail application 
and attach the scanned image 
file to new e-mail Scanner 
						

							36
Exiting CaptureOnTouch
Click   at the top of the window to close the CaptureOnTouch main 
window
. When doing so, the main window closes but CaptureOnTouch 
is kept as resident in the system.
To stop CaptureOnTouch being resident in the system, click the 
(CaptureO
nTouchiconj in the taskbar, and select [Exit] from the 
menu.
CaptureOnTouch becomes no longer resident in the system and the 
icon disappears from the taskbar.
Restarting CaptureOnTouch
To use CaptureOnTouch after it is no longer resident in the system, 
restart it by following the procedure below. CaptureOnTouch will start 
and become resident in the system again.
 Click [Start] – [All  Programs] – [Canon  DR-M1060] – [DR-M1060 
CaptureOnTouch].
Scan First
Scan a document and then select the output method. This method 
allows you to easily scan a document by just following the instructions 
on the screen.
Operation Flow
1Place the document in the scanner.
2Click [Scan First].
The top screen of Scan First appears.
Scan the document
▼
Configure the output settings
▼
Output the scanned images 
						

							37
3Set the scan method in the top screen.
ASpecify whether to enable continuous scanning. When 
scanning multiple documents as one scanned image or 
splitting up a large document to scan in parts, select [ON] to 
enable continuous scanning.
BSpecify whether to scan the document in full auto mode. When 
you want to specify arbitrary scanning conditions, select [OFF] 
and configure the scanner settings. (See p. 41)
4Click the Start button.
The document is scanned. While scanning is in progress, the 
number of pages scanned is displayed in addition to the scanner 
settings.
When scanning is finished, the Output settings screen appears.
IMPORTANT
If you configure scanning conditions that consume a large 
amount of the computer’s memory, scanning may stop because 
of insufficient memory. If an error message appears due to 
insufficient memory while scanning is in progress, exit the 
application, change the scanning conditions, and then try 
scanning again.
Hint
If a document is scanned when [Enable continuous scanning] is 
set to [ON], the Continuous Scanning screen (see p. 43) appears 
when the scanning of the document is finished.
If you place the next document and click [Scan], scanning of the 
document starts.
When scanning of all the documents is finished, click [Next step].
A
B 
						

							38
5Configure the settings related to output and then output 
the scanned images.
 
AConfigure the settings related to output. (See p. 44)
BClick this button to output the scanned images. The button 
name differs for each output method. For example, it is [Save] 
when the output method is set to [Save to folder].
When output is finished, the complete screen appears. Scan First 
is now finished.
Hint
 Clicking [Return to top] returns to the main screen of Scan First.
 When output methods apart from [Attach to E-mail] or [Print] are 
specified, you can click [Open storage folder] to open the folder in 
which the scanned images were saved.
Select Scan Job
Register scanning settings from the scanning conditions to the output 
method as jobs, and then scan a document by just selecting the job 
that suits your purpose. This method is convenient when you want to 
repeat scanning using a set procedure.
Operation Flow
Registering and Editing Jobs
In CaptureOnTouch, up to 9 jobs can be registered for use with Select 
Scan Job.
1Click the   button.
B A
Register the job
▼
Select the job
▼
Scan the document
▼
Output the scanned images 
						

							39
2Enter the job name, and press the Enter key.
Hint
Job numbers up to 9 are added (in numerical order) to the end of 
the set job name. By specifying the job number with the operating 
panel, you can start scanning after pressing the operating panel 
button. (See p. 41)
3Specify the output method of the job. (See p. 44)
4Click [Output settings], and configure the output settings.
The output setting items differ depending on the specified output 
method. For details on the setting items, see the Help of 
CaptureOnTouch.
Selecting a Job and Scanning
1Place the document in the scanner. (See p. 24)
The top screen of Select Scan Job appears.
2Click a job. 
						

							40
Hint
 If you set [Enable continuous scanning] to [ON], you can 
continue to scan additional documents after all the pages of the 
initial document are scanned.
 If you set [Check output after scanning] to [ON], you can check 
the output settings after scanning.
3Click the Start button.
The document is scanned. While scanning is in progress, the 
number of pages scanned is displayed in addition to the scanner 
settings.
When all the pages of the document are scanned, the scanned 
images are output according to the registered job settings and the 
complete screen appears.
IMPORTANT
If you configure scanning conditions that consume a large amount of 
the computer’s memory, scanning may stop because of insufficient 
memory. If an error message appears due to insufficient memory 
while scanning is in progress, exit the application, change the 
scanning conditions, and then try scanning again.
Hint
 Clicking [Return to top] returns to the top screen of Select Scan Job.
 When output methods apart from [Attach to E-mail] or [Print] are 
specified, you can click [Open storage folder] to open the folder in 
which the scanned images were saved.
When [Enable continuous scanning] is set to [ON]
The Continuous Scanning screen (see p. 43) appears when all the 
pages of the document are scanned.
If you want to scan another document, place the document in the 
scanner and then click [Scan].
When scanning of all the documents is finished, click [Next step].