Canon Projector WUX6010 User Manual

161
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced GuideUsing Menus
Menu Description
Advanced Projection
Other InformationMaintenance
Product Specifications
Troubleshooting
Other Information 

162
Maintenance
Cleaning the Projector and the Air Filter
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Wipe the projector’s main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of 
detergent in it, squeeze the cloth thoroughly, and then wipe the projector with it. 
After cleaning, wipe the projector with a dry cloth.
Request Internal Cleaning Regularly...

163
Maintenance
Other Information
Maintenance
Cleaning the Air Filter
The air filter protects the lens and mirror inside the projector from dust and dirt. 
Should the air filter become clogged with dust, the projector may be damaged since 
it will block the air flow into the projector and raise the internal temperature of the 
projector. The following screen is displayed when turning on the projector if the air 
filter needs to be cleaned. Clean the air filter if it is displayed.
•Turn the power of the...

Maintenance
164
Replacing the Air Filter
Follow the procedure below when replacing the air filter.
1Turn off the projector power and remove the power plug.
2Hook your finger around the air 
filter frame handle on the side of 
the projector, and pull the air 
filter out to remove it.
3Remove the filter from the air 
filter frame. First disengage the 
tab on the inside, then remove 
the entire air filter from the 
frame.
4Install a new air filter into the 
frame. First insert the air filter 
tab into the...

165
Maintenance
Other Information
Maintenance
Replacing the Lamp
When the usage time of the lamp exceeds a certain amount of time, the following 
message (two types) is displayed for 10 seconds every time the projector is turned 
on.
2,700 hours to less than 3,000 hours
Prepare a new lamp when this screen is displayed.
•Only the [ ], [ ], OK, POWER, FOCUS, ZOOM and LENS SHIFT buttons are 
available while this screen is displayed.
•When you press the POWER button, “Push POWER button again to turn off...

Maintenance
166 • Lamps are more likely to rupture once the lamp replacement 
message has been displayed. Replace the lamp with a new one as 
soon as possible.
• Lamps should be replaced about every 3,000 hours. Note that there 
is no guarantee about how long lamps will last.
• Useful life of lamps varies widely from lamp to lamp and depending 
on the environment of use. Some lamps may fail or rupture soon 
after they are first used.
• Dispose of used lamps in accordance with local regulations. 

167
Maintenance
Other Information
Maintenance
Replacement Lamp
This projector uses the following lamps.
Lamp part no.: RS-LP09
Contact the Canon Customer Support Center when purchasing a replacement 
lamp.
Precautions when replacing lamps that stop working
If the illumination suddenly stops when the projector is in use or after 
you turn it on, the lamp may be broken. In this case, never attempt to 
replace the lamp by yourself. Always request service from the Canon 
Customer Support Center....

Maintenance
168
Lamp Replacement Procedure
1Turn off the projector power and remove the power plug.
2Loosen one screw and open the lamp cover in the direction of the arrow.
The lamp cover screw is attached to the lamp cover and designed to prevent it 
from falling off.
3Loosen the 3 screws on the inside of the lamp unit, then slowly pull out 
the lamp unit in the direction of the arrow.
Even when the screws are loosened, they will not fall off the lamp unit.
4Fully insert a new lamp unit and secure it...

169
Maintenance
Other Information
Maintenance
7Select [Reset] > [Yes] to reset the lamp counter.
• It is recommended that you also replace the air filter when you replace the lamp. (P162)
• Contact the Canon Customer Support Center for further information.
• Replacement air filter part no.: RS-FL01 

Maintenance
170
Installing / Removing the Lens Unit
■Installing the Lens Unit
1Use a Phillips-head screwdriver and loosen the lamp cover screw, then 
open the lamp cover.
The lamp cover screw is attached to the lamp cover and designed to prevent it 
from falling off.
• Before installing or removing the lens unit, be sure to disconnect the 
power plug or connector. Failure to do so may result in fire, electric 
shock, or injury.
• When hanging the projector from a ceiling, put the projector down 
on the...