Canon Projector WUX500 User Manual

							131
Menu Description
Advanced Guide
Menu Description
2Enter setting details in the fields shown (1), and then click [OK] (2).
3A confirmation window appears. Check the contents and if they are 
correct, click [Apply].
The settings are applied to the projector.
Selecting [Wired], [Wireless], or [Password] in the menu will cause this 
message to be displayed: “Save completed. Please change setting and 
reconnect.”
If you select functions other than above, “Save completed” is displayed. Click 
[Back to top] to return to the top page of the web screen.
(1)
(2) 
						

							Menu Description
132
Setting a Password [Password]
From [Password] in the settings screen, you can set a user name and password for 
web screen login. For the setting procedure, refer to “Network Setting” (P130).
ItemExplanationFactory default setting
User nameWhen logging into the web screen, 
enter the user name in 1-byte 
alphanumeric characters and symbols 
(4 -15 characters).root
New passwordWhen logging into the web screen, 
enter the password in 1-byte 
alphanumeric characters and symbols 
(4 -15 characters).system
Confirm new passwordFor confirmation, enter the same 
password that you entered in [New 
password].system 
						

							133
Menu Description
Advanced Guide
Menu Description
Basic Wired Network Settings [Wired]
From [Wired] on the settings screen, you can complete basic network information 
for wired connections. For the setting procedure, refer to “Network Setting” (P130).
ItemExplanationFactory default setting
MAC address Shows the projector’s wired MAC 
address.The projector’s wired 
MAC address
DHCP Select whether to turn the DHCP 
function on or off for wired connections. 
The following settings cannot be 
configured manually when this setting is 
[ON], because the IP address is 
acquired from the server.
[IP address]
[Subnet mask]
[Default gateway]OFF
IP  address Enter the projector’s wired IP address in 
1-byte numbers.192.168.254.254
Subnet mask Enter the wired subnet mask in 1-byte 
numbers.255.255.255.0
Default gateway Enter the wired default gateway IP 
address in 1-byte numbers.0.0.0.0
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to 
the network.
If the network subnet mask was changed, select [Subnet mask] in the above screen and 
set the new subnet mask. 
						

							Menu Description
134
Basic Wireless Network Settings [Wireless]
From [Wireless] on the settings screen, you can complete basic network 
information for wireless connections. For the setting procedure, refer to “Network 
Setting” (P130).
ItemExplanationFactory default setting
MAC address Shows the projector’s wireless MAC 
address.The projector’s wireless 
MAC address
DHCP Select whether to turn the DHCP 
function on or off for wireless 
connections. The following settings 
cannot be configured manually when 
this setting is [ON], because the IP 
address is acquired from the server.
[IP address]
[Subnet mask]
[Default gateway]OFF
IP address Enter the projector’s wireless IP 
address in 1-byte numbers.192.168.253.254
Subnet mask Enter the wireless subnet mask in 1-
byte numbers.255.255.255.0
Default gateway Enter the wireless default gateway IP 
address in 1-byte numbers.0.0.0.0
Wi-Fi Protected Setup Select a simple method of establishing 
a wireless connection.None (configure 
manually)
Mode Select the wireless connection mode. infrastructure mode
Select  SSID Select the wireless access point’s SSID. 
Click the [Refresh] button to update the 
list. If the SSID is not listed, enter it in 
single-byte alphanumeric characters (1-
32 characters).
Security Select the wireless security setting. Open 
						

							135
Menu Description
Advanced Guide
Menu Description
Specifying Networked Multi-Projection Settings [NMPJ Password]
From [NMPJ Password] in the settings screen, you can specify the items needed 
for NMPJ authentication. For the setting procedure, refer to “Network Setting” 
(P130).
Channel Shows the wireless channel number. 
When [Mode] is set to projector access 
point (PJ AP) mode, a channel can be 
selected.1
Key ID Select the wireless WEP key ID. 1
Key type Select the wireless security key input 
type.ASCII
Key Enter the wireless security key. 
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to 
the network. If the network subnet mask was changed, select [Subnet mask] in the above 
screen and set the new subnet mask.
ItemExplanationFactory default setting
Password Enter the password required for a 
networked multi-projection connection 
in single-byte alphanumeric characters 
(0-15 characters).
Confirm password For confirmation, enter the same 
password as you entered in [Password].
For details on Networked Multi-Projection (NMPJ), refer to the NMPJ user’s manual.
ItemExplanationFactory default setting 
						

							Menu Description
136
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error 
mails and test mails. For the setting procedure, refer to “Network Setting” (P130).
* When the interval is set to 0 seconds, repeated attempts to send mail are made 
(as set in [Mail resend times]) without pausing between attempts.
ItemExplanationFactory default setting
To :
Enter the recipient address for error mails 
in 1-byte alphanumeric characters and 
symbols (1 - 63 characters).MailUserAccount
Cc:
Enter the CC address for error mails in 1-
byte alphanumeric characters and symbols 
(1 - 63 characters).
From:
Enter the sender address for error mails 
in 1-byte alphanumeric characters and 
symbols (1 - 63 characters)[email protected]
SMTP server IP address Enter the SMTP server IP address in 1-
byte numbers.0.0.0.0
SMTP server port 
number
Enter the SMTP server port number in 1-
byte numbers (1 - 65535).25
SNTP server IP address Enter the SNTP server IP address in 1-
byte numbers.0.0.0.0
Time zone Select the time zone where the 
projector is used.(GMT) Dublin, Lisbon, 
London
Mail resend interval* Enter the interval for resending mail 
when an error occurred (unit: seconds) 
within the range of 0 - 59 seconds using 
1-byte numbers.10
Mail resend times Enter the number of times to resend 
mail when an error occurred within the 
range of 0 - 255 using 1-byte numbers.3
Error report Select whether to turn the error mail 
sending function on or off.OFF 
						

							137
Menu Description
Advanced Guide
Menu Description
Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings screen, you can configure the settings for 
authentication of mail that is sent when an error occurs. For the setting procedure, 
refer to “Network Setting” (P130).
ItemExplanationFactory default setting
Mail authentication Select the mail authentication method. 
If OFF is selected, the other mail 
authentication settings cannot be 
changed.OFF
User name
Enter the user name to use for mail 
authentication in 1-byte alphanumeric 
characters and symbols (1 - 63 
characters).
Password
Enter the password for mail 
authentication in 1-byte alphanumeric 
characters and symbols (1 - 63 
characters).
Confirm password  For confirmation, enter the same 
password as you entered in 
[Password].
POP3 server IP 
addressEnter the POP3 server IP address in 1-
byte numbers.0.0.0.0
POP3 server port 
numberEnter the POP3 server port number in 
1-byte numbers (1 - 65535).11 0
POP before SMTP 
response time
Enter the SMTP authentication timeout 
period after POP3 authentication (unit: 
milliseconds) using 1-byte numbers (0 - 
9999 milliseconds).300 
						

							Menu Description
138
Sending a Test Mail [Send test mail]
From [Send test mail] in the settings screen, you can send a test mail to the mail 
address that was set in [Mail]. The settings cannot be changed from this screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to 
control of projectors which use SNMP (Simple Network Management Protocol). For 
the setting procedure, refer to “Network Setting” (P130).
ItemExplanation
To: The recipient address which was set from [Mail] in the settings screen (P136) is 
displayed.
Cc: The CC address which was set from [Mail] in the settings screen (P136) is 
displayed.
From: The sender address which was set from [Mail] in the settings screen (P136) is 
displayed.
Subject: The predetermined mail title “Canon Projector test” is displayed. 
						

							139
Menu Description
Advanced Guide
Menu Description
Setting Projector Information [Projector info.]
From [Projector info.] in the settings screen, you can enter relevant comments such 
as projector names and locations where projectors are installed so that the 
information can be used to identify projectors when multiple projectors are installed 
on the network. For the setting procedure, refer to “Network Setting” (P130).
ItemExplanationFactory default setting
SNMP Select the SNMP function version. If 
OFF is selected, the SNMP function will 
be turned off and the other settings in 
this screen cannot be changed.OFF
Receive community Enter the community name which will 
receive projector information in 1-byte 
alphanumeric characters and symbols 
(1 - 15 characters).
Password Enter the community settings password 
in 1-byte alphanumeric characters and 
symbols (8 - 15 characters). It can be 
set only when the SNMP version is V3.
Confirm password For confirmation, enter the same 
password as you entered in [Password].
ItemExplanationFactory default setting
Projector name Enter the projector name in 1-byte 
alphanumeric characters and symbols 
(1 - 63 characters).
Canon Projector001
CommentEnter any relevant notes, such as where 
the projector is installed.
Some characters such as # cannot be used for [Projector name] and [Comment]. 
						

							Menu Description
140
Setting PJLink [PJLink]
From [PJLink] in the settings screen, you can set the PJLink functions which are the 
standard for projector management on a network. For the setting procedure, refer 
to “Network Setting” (P130). For information about PJLink, refer to “What is 
PJLink?” (P124).
Setting Up a Controller Manufactured by Crestron Electronics 
[Crestron Controller]
The [Crestron e-Control] screen will open. For details on the Crestron Controller, 
visit the Crestron website.
http://www.crestron.com/
ItemExplanationFactory default setting
PJLink Turn the PJLink function on or off. If 
OFF is selected, the PJLink function 
will be turned off and the other settings 
in this screen cannot be changed.ON
PJLink authentication Select whether to turn the PJLink 
authentication function on or off. The 
following settings cannot be changed 
when this setting is [OFF].
[Password]
[Confirm password]ON
Password Enter the PJLink authentication 
password in 1-byte alphanumeric 
characters (1 - 32 characters).system
Confirm password For confirmation, enter the same 
password that you entered in 
[Password].system