Canon Projector WUX10 Mark II User Manual

31
Table of Contents
Safety Instructions
Before Use
Projecting an Image 
Useful Functions Available During a Presentation
 
Setting Up Functions from Menus
Connecting the Projector to Network
Appendix
Index
Projecting an 
Image 

32
Steps for Setting Up the Projector and Projecting an Image
Performing the Auto Setup (P47)
Connecting the Projector to Equipment (P36)
Turning on the Power
 (P44)
Selecting an Input Signal (P49)
Adjusting the Image (P51)
Do the following adjustments.
 Setting the Display Resolution of the Computer 
(P51)
 Adjusting misaligned images or flickering of the 
screen using the Auto PC (P52)
 Adjusting the Image Size
 (P53)
 Adjusting the Focus (P54)
 Adjusting keystone Distortion (P55)
Making Fine...

33
Projecting an Image 
Setting Up the Projector
■Placing in Front of the Screen
Place the projector in front of the screen.
 Be sure to place the projector parallel to the 
screen to ensure distortion-free projections.
 The screen must not be exposed to direct sun-
light or light from lighting equipment. In a bright 
room, it is recommended to limit ambient light-
ing in order to improve the image quality.
Optical axisScreen
Projected Image Size
The projected image size is determined by the distance...

Setting Up the Projector
34
■Placing on a Level Place
Be sure to keep the projector as horizontal as possible.
If you need to point the projector up (for example, when the screen is placed on a higher 
position), follow the instruction given in When Pointing the Projector Up on the following 
page.
 Adjust the tilt of the projecting image using the rear adjustable foot.
Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (Ceiling mounted) with it turned up side 
down or place...

35Setting Up the Projector
Projecting an Image 
■ When Pointing the Projector Up
When the screen is placed on a higher position, point the projector up using the adjust-
able foot.
You can point it up as far as 10 degrees.
The keystone distortion of the projecting image can be corrected with the auto keystone 
(P47) or by using the keystone distortion adjust function (P55).
1Lift the front side of the projector and 
push the adjusting foot lock button to 
extend the adjustable foot.
2Raise the image to...

36
Connecting the Projector
Connectable Equipment and Input Terminals
DIGITAL PC
ANALOG PC-1Use this name to select the appropriate image.  : Video signal or data flow
DVI-I IN terminalThe name of the terminal to which to connect 
equipment.(Pxxx) : indicates the page(s) to refer to.
Computer (P37, P38) AV equipment (P40)
Digital video camera* (P40)Computer (P37, P38)
AV equipment (P42)
AV equipment (P41)
Amplified speaker
(P39, P43)
Digital camera* (P41) Digital video 
camera* (P41) DVI-I IN terminal...

37Connecting the Projector
Projecting an Image 
Connecting the Projector to the Computer
Connect the projector to the computer.
Before connecting the cables, turn off both the projector and computer.
The digital connection (P38) is recommended when projecting a WUXGA or UXGA image  
in high quality.
■Connecting to RGB Monitor Output Terminal (analog connection)
Supplied computer connection cable (Input signal type: [ANALOG PC-1] - P49)
VGA cable (Input signal type: [ANALOG PC-2] - P49)
 Use full...

Connecting the Projector
38
BNC cable (Input signal type: [ANALOG PC-2] - P49)
■Connecting to DVI Monitor Output Terminal (digital connection)
DVI cable (Input signal type: [DIGITAL PC] - P49)
 It cannot project a signal whose dot clock is 170MHz or higher.
 Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
turns down the sound.
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
turns down the sound.
Monitor output...

39Connecting the Projector
Projecting an Image 
■Outputting Audio to Speakers
It is possible to output sound of projected images to amplified speakers.
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor 
turns down the sound.
Commercial audio cable To AUDIO OUT
Audio input terminal
(AUDIO IN)
RCA terminal
Mini jack Projector
Speaker 

Connecting the Projector
40
Connecting to AV Equipment
Connect the projector and AV equipment.
Before connecting the cables, turn off both the projector and AV equipment.
The description provided here is just examples. For more detailed information, refer to the 
manual for the connecting AV equipment.
■Connecting to Digital Video Output Terminal (digital connection)
HDMI cable (Input signal type: [HDMI] - P49)
Digital video camera
Digital video
output terminal
(HDMI terminal)Commercial HDMI cable
* HDMI...