Canon printer PIXMA MX492 User Manual

							•Make sure that you push in the ink cartridge completely until you hear a clicking sound.•
If an orange tape is adhered to the ink cartridge, peel it off completely.
Any remaining tape will hinder ink output.
•
Check that the ink cartridges are installed in their correct positions.
Start Print Head Alignment dialog box
This dialog box allows you to adjust the attachment position for the print head, or to print the current setting value for the print head position.
Align Print Head Aligns the print head.
Print head alignment corrects the installation positions of the print head and improves deviated colors
and lines.
Align the print head immediately after installing the print head.
Print Alignment Value Click this button to check the current setting value of the print head position.Prints the current setting value for the print head position.
Print Head Alignment dialog box To adjust the print head position manually, click  Align Print Head in the Start Print Head Alignment
dialog box, and perform the operations instructed in the messages. The  Print Head Alignment dialog
box is then displayed.
This dialog box allows you to check the printed pattern and adjust the print head position.
Preview Window Displays the pattern of  Print Head Alignment, and checks the position of the selected pattern.
You can also change the setting by clicking the pattern on the screen directly.
Select the Pattern Number Compare the printed adjustment patterns, and enter the pattern number of the pattern with the
least visible streaks or horizontal stripes into the corresponding box.
Note
•
If you do not know how to analyze the printed pattern, see Aligning the Print Head Position from
Your Computer .
Initial Check Items
Before running  Nozzle Check, check that the printer power is on, and open the cover of the printer.
Check the following items for each ink.
•
Check the amount of ink  remaining in the cartridge.
•
Make sure that you push in the ink cartridge completely until you hear a clicking sound.
•
If an orange tape is adhered to the ink cartridge, peel it off completely.
Any remaining tape will hinder ink output.
•
Check that the ink cartridges are installed in their correct positions.
Ink Cartridge Settings dialog box
When you click  Ink Cartridge Settings , the Ink Cartridge Settings  dialog box is displayed.
This feature enables you to specify the most appropriate FINE cartridge among installed cartridges
431 
						

							according to an intended use.
When one of the FINE cartridges becomes empty and cannot be replaced immediately by a new one, you
can specify the other FINE cartridge that still has ink and continue printing.
Ink Cartridge Selects the FINE cartridge you use for printing.Color Only Uses the color FINE cartridge only.
Black Only Uses the black FINE cartridge only.
Both Black and Color Uses the FINE cartridges installed on the printer, which are color and black.
Important
•
When the following settings are specified,  Black Only does not function because the printer
uses the color FINE cartridge to print documents.
•
Other than  Plain Paper , or Envelope  is selected for  Media Type on the Main tab
•
Borderless  is selected from the  Page Layout list on the Page Setup  tab
•
Do not detach the FINE cartridge that is not in use. Printing cannot be performed while either
FINE cartridge is detached.
Auto Power Settings dialog box When you click  Auto Power, the Auto Power Settings  dialog box is displayed.
This dialog box allows you to manage the printer power from the printer driver.
Auto Power Off Selects the auto power-off setting.If a printer driver operation or a printer operation is not performed within the specified time, the printer
turns off.
Important
•
In the following cases, you can set  Auto Power Off but the power will not be turned off
automatically.
•
When you use the printer by connecting it to a network
•
When you use the printer by connecting it to a telephone line via a modular cable
Quiet Settings dialog box When you click  Quiet Settings, the Quiet Settings  dialog box is displayed.
Quiet Settings  dialog box allows you to specify a setting that reduces the operating noise of the printer.
Select when you wish to reduce the operating noise of the printer at night, etc.
Using this function may lower the print speed.
Do not use quiet mode Select this option when you wish to use the printer with volume of normal operating noise.
Always use quiet mode Select this option when you wish to reduce the operating noise of the printer.
432 
						

							Use quiet mode during specified hoursSelect this option when you wish to reduce the operating noise of the printer during a specified period
of time.
Set the  Start time  and the End time  of the quiet mode you wish to be activated. If both are set to the
same time, the quiet mode will not function.
Important
•
You can set the quiet mode from the operation panel of the printer, the printer driver, or ScanGear
(scanner driver).
No matter how you use to set the quiet mode, the mode is applied when you perform operations from
the operation panel of the printer or printing and scanning from the computer.
Custom Settings dialog box When you click  Custom Settings , the Custom Settings  dialog box is displayed.
If necessary, switch between various modes of printer operation.
Prevent paper abrasion The printer can increase the gap between the print head and the paper during high-density printing to
prevent paper abrasion.
Check this check box to enable this function.
Align heads manually Usually, the  Print Head Alignment  function on the Maintenance tab is set to automatic head
alignment, but you can change it to manual head alignment.
If the printing results of automatic print head alignment are not satisfactory, 
perform manual head
alignment .
Check this check box to perform the manual head alignment.
Prevent paper double-feed Select this check box only if the printer is feeding multiple sheets of plain paper at the same time.
Important
•
Using this function slows down the print speed.
Rotate 90 degrees left when orientation is [Landscape] On the  Page Setup  tab, you can change the rotation direction of the  Landscape in the Orientation .
To rotate the document 90 degrees to the left when printing, select the check box.
Don't detect mismatch of paper settings when printing from computer When you print documents from your computer and the paper settings on the printer driver and the
cassette paper information registered on the printer do not match, this setting disables the message
display and allows you to continue printing.
To disable detection of paper setting mismatches, select this check box.
Ink Drying Wait Time The printer can pause before printing a subsequent page. Moving the slider to the right increases the
pause time, and moving the slider to the left decreases the time.
If the paper gets stained because the next page is ejected before the ink on the printed page dries,
increase the ink drying wait time.
Reducing the ink drying wait time speeds up printing.
433 
						

							About dialog box
When you click  About, the About  dialog box is displayed.
This dialog box displays the version, copyright, and module list of the printer driver. You can select the
language to be used and switch the language displayed in the setup window.
Modules Lists the printer driver modules.
Language Specifies the language you wish to use in the 
printer driver setup window .
Important
•
If the font for displaying the language of your choice is not installed in your system, the
characters will be garbled.
Related Topics
Cleaning the Print Heads from Your Computer
Aligning the Print Head Position from Your Computer
Use Your Computer to Print a Nozzle Check Pattern
Setting the Ink Cartridge to be Used
Managing the Printer Power
Reducing the Printer Noise
Changing the Printer Operation Mode
434 
						

							Canon IJ Preview DescriptionCanon IJ Preview is an application software that displays what the print result will look like before adocument is actually printed.
The preview reflects the information that is set within the printer driver and allows you to check the
document layout, print order, and number of pages. You can also change the media type and paper source
settings.
When you want to display a preview before printing, open the 
printer driver setup window , and check the
Preview before printing  check box on the Main tab.
File Menu
Selects the print operation.
Start Printing Ends the Canon IJ Preview and then starts printing the document that is displayed on the preview
screen.
This command has the same function as the  Start Printing on the toolbar.
Cancel Printing Ends the Canon IJ Preview and cancels the printing of the document that is displayed on the
preview screen.
This command has the same function as the  Cancel Printing on the toolbar.
Exit Ends the Canon IJ Preview.
Page Menu This menu includes the following commands to select page to be displayed.All of these commands except  Page Selection... can also be selected from the toolbar.
Note
•
If the pages are being spooled, the last spooled page becomes the last page.
•
If the Page Layout  setting on the  Page Setup tab is specified to  Page Layout, Tiling/Poster , or
Booklet , the number of pages is the number of sheets to be used for printing, and not the number
of pages in the original document created with the application software.
435 
						

							•If duplex printing manually has been set, the front pages which will be printed first are all displayedtogether, and then the back pages are displayed.
First Page Displays the first page of the document.
If the currently displayed page is the first page, this command is grayed out and cannot be selected.
Previous Page Displays the page located before the currently displayed page.
If the currently displayed page is the first page, this command is grayed out and cannot be selected.
Next Page Displays the page located after the currently displayed page.If the currently displayed page is the last page, this command is grayed out and cannot be
selected.
Last Page Displays the last page of the document.
If the currently displayed page is the last page, this command is grayed out and cannot be
selected.
Page Selection... Displays the  Page Selection  dialog box.
This command allows you to specify the page number of the page to be displayed.
Zoom Menu Selects the ratio of the actual size printed on the paper to the preview display size.
You can also select the ratio from the drop-down list box located on the toolbar.
Whole Displays the entire page of data as one page.
50% Reduces the displayed data to 50% of the actual size to be printed.
100% Displays the data at the actual size to be printed.
200% Enlarges the displayed data to 200% of the actual size to be printed.
400% Enlarges the displayed data to 400% of the actual size to be printed.
Option Menu This menu includes the following command:Displays Print Page Information Displays print setup information (including printer paper size, media type, and page layout) for eachpage at the left side of the preview screen.
This screen also allows you to change the media type and paper source settings.
Help Menu When you select this menu item, the Help window for Canon IJ Preview is displayed, and you can
check the version and copyright information.
436 
						

							Start Printing buttonPrints the documents selected in the document list.
The printed documents are deleted from the list, and when all documents are printed, the Canon IJ XPS
Preview closes.
Cancel Printing button Ends the Canon IJ Preview, and cancels the printing of the document that is displayed on the previewscreen.
You can click this button while spooling.
Print Page Information Screen Displays print setup information for each page at the left side of the preview screen.
This screen also allows you to change the media type and paper source settings.
Important
•
If the media type and paper source are set from the application software, those settings have priority and the changed settings may become ineffective.
Printer Paper Size Displays the paper size of the document to be printed.
Media Type You can select the media type of the document to be printed.
Paper Source You can select the paper source of the document to be printed.
Page Layout Displays the page layout of the document to be printed.
437 
						

							Canon IJ XPS Preview DescriptionCanon IJ XPS Preview is an application software that displays what the print result will look like before a
document is actually printed.
The preview reflects the information which is set within the printer driver and allows you to check the
document layout, print order, and number of pages. The preview also allows you to edit the print document,
edit the print pages, change the print settings, and perform other functions.
When you want to display a preview before printing, open the 
printer driver setup window , and check the
Preview before printing  check box on the Main tab.
Important
•
To use the Canon IJ XPS Preview, you must have Microsoft .NET Framework 4 Client Profile installed
on your computer.
File Menu Selects print operation and print history settings:
Print Prints the documents selected in the document list.The printed documents are deleted from the list, and when all documents are printed, the Canon IJ
XPS Preview closes.
This command has the same function as 
 (Print) on the toolbar and the  Print in the print
settings area.
Print All Documents Prints all documents in the document list and closes the Canon IJ XPS Preview.
Save Print History Switches whether the documents printed from the Canon IJ XPS Preview are to be saved as print
history entries.
History Entry Limit Switches the maximum number of print history registrations.Select  10 Entries , 30 Entries , or 100 Entries .
438 
						

							Important•
If the limit on the number of registration is exceeded, the print history registrations are deletedstarting from the oldest one.
Add documents from history to the list Adds the document saved in the print history to the document list.
Exit Ends the Canon IJ XPS Preview. The documents remaining in the document list will be deletedfrom the list.
This command has the same function as the  Exit in the print settings area.
Edit Menu Selects the method for editing multiple documents or pages.
Undo Reverses the previous change.
If the change cannot be reversed, this function is grayed out and cannot be selected.
This command has the same function as the 
(Undo) on the toolbar.
Documents Selects the method for editing print documents.
Combine Documents Combines the documents selected in the document list into one document.
If only one document is selected, this command is grayed out and cannot be selected.
This command has the same function as the 
(Combine Documents) on the toolbar.
Reset Documents Returns the document selected in the document list to their status before they were added to
the Canon IJ XPS Preview.
The combined documents are separated, and the original documents are restored.
This command has the same function as the 
(Reset Documents) on the toolbar.
Move Document Use the following command to change the order of the documents selected in the document
list.
Move to First Moves the selected print document to the beginning of the document list.If the currently selected document is the first document, this command is grayed out and
cannot be selected.
Move Up One Moves the selected print document one up from its current position.
If the currently selected document is the first document, this command is grayed out and
cannot be selected.
Move Down One Moves the selected print document one down from its current position.
If the currently selected document is the last document, this command is grayed out and
cannot be selected.
Move to Last Moves the selected print document to the end of the document list.If the currently selected document is the last document, this command is grayed out andcannot be selected.
439 
						

							Delete DocumentDeletes the selected document from the document list.If the document list contains only one document, the document is grayed out and cannot be
selected.
This command has the same function as the 
(Delete Document) on the toolbar.
Grayscale Printing Allows you to change the monochrome print settings.
This command has the same functionality as the  Grayscale Printing check box in the print
settings area.
Page Layout Printing... Opens the  Page Layout Printing  dialog box.
This dialog box allows you to set  Page Layout Printing, Pages , Page Order , and Page
Border .
Duplex Printing... Opens the  Duplex Printing  dialog box.
This dialog box allows you to set  Duplex Printing (Manual), Stapling Side , and Margin .
Copies... Opens the  Copies dialog box.
This dialog box allows you to set  Copies, Collate , and Print from Last Page .
Pages Selects the method for editing print pages.
Delete Page Deletes the currently selected page.If page layout printing is set, the pages enclosed with red frame will be deleted.
This command has the same function as the 
(Delete Page) on the toolbar.
Restore Page Restores pages that were deleted with the  Delete Page function.
To restore pages, you must select the  View Deleted Pages check box on the Option menu
and display the deleted pages as thumbnails.
Move Page Use the following command to change the order of the currently selected pages.
Move to First Moves the currently selected page to the beginning of the document.
If the currently selected page is the first page, this command is grayed out and cannot be selected.
Move Forward One Moves the currently selected page one position in front of its current position.If the currently selected page is the first page, this command is grayed out and cannot be selected.
Move Backward One Moves the currently selected page one position after its current position.If the currently selected page is the last page, this command is grayed out and cannot be
selected.
440