Canon printer MAXIFY MB2020 User Manual

Default Values Set at Factory (Network)Default Values of the LAN ConnectionItemThe defaultChange LANDisable LANSSIDBJNPSETUPCommunication modeInfrastructureWireless LAN securityDisableIP address  (IPv4 )Auto setupIP address  (IPv6 )Auto setupSet printer name *XXXXXXXXXXXXEnable/disable IPv6EnableEnable/disable WSDEnableTimeout setting1 minuteEnable/disable BonjourEnableService nameCanon MB2000 seriesLPR protocol settingEnableWireless LAN DRX settingEnable
("XX" represents alphanumeric...

Connecting the Machine to the Computer Using a USB CableConnect the machine and the computer using a USB cable as the illustration below. The USB port is located
on the rear of the machine.282 

When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detectionresult screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information using the operation panel
of the...

Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the machine with LAN or to change the connection method between the
machine and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the machine with LAN, perform setup with the Setup CD-ROM orperform it according to the instructions on our website....

Printing Out Network Setting InformationYou can print out the current network settings of the machine using the operation panel of the machine.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the machine is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Select   Setup  on the HOME screen.
LCD and Operation Panel
The menu screen is displayed.
4.
Select   Device settings , then press the OK button.
5.
Use the  button to...

AuthenticationMethod of the Authenticationnone/auto/open/shared/WPA-PSK/WPA2-PSKSignal StrengthSignal Strength0 to 100 [%]TCP/IP VersionTCP/IP VersionIPv4 & IPv6/IPv4IPv4 IP AddressSelected IP Address (IPv4)XXX.XXX.XXX.XXXIPv4 Default GatewayDefault Gateway (IPv4)XXX.XXX.XXX.XXXSubnet MaskSubnet MaskXXX.XXX.XXX.XXXIPv6 IP Address *2Selected IP Address (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXIPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXSubnet Prefix Length...

*3 Only IPv6 and the IPsec setting are enabled, the status of the network is printed.
287 

About Network Communication
Changing and Confirming Network Settings
Screens for Network Connection of IJ Network Tool
Other Screens of IJ Network Tool
Appendix for Network Communication
288 

Changing and Confirming Network Settings
IJ Network Tool
Changing the Settings in the Wireless LAN Sheet
Changing the WEP Detailed Settings
Changing the WPA/WPA2 Detailed Settings
Changing the Settings in the Wired LAN Sheet
Changing the Settings in the Admin Password Sheet
Monitoring Wireless Network Status
Initializing the Network Settings of the Machine
Viewing the Modified Settings
289 

IJ Network ToolIJ Network Tool is a utility that enables you to display and modify the machine network settings. It is installed
when the machine is set up.
Important
•
To use the machine over LAN, make sure you have the equipment necessary for the connection type, such as an access point or a LAN cable.
•
Do not start up IJ Network Tool while printing.
•
Do not print when IJ Network Tool is running.
•
If the firewall function of your security software is turned on, a message may appear warning thatCanon...