Canon printer MAXIFY MB2020 User Manual

Note•
This item has the same function as Refresh in the View menu.
3.
Configuration...
Click to configure settings of the selected printer.
Configuration Screen
Note
•
You cannot configure a printer that has the status  Not Found.
•
This item has the same function as  Configuration... in the Settings  menu.
Canon IJ Network Tool Menus The following menu is displayed from the  Canon IJ Network Tool screen.
1.
File menu
Exit Exits IJ Network Tool.
2.
View  menu
Status Displays the  Status screen to confirm...

•If No Driver  is displayed for the name, associate the port with the printer.
When the Printer Driver Is Not Associated with a Port
•
If Not Found  is displayed for the status, check the followings:
•
The access point is turned on.
•
When using wired LAN, the LAN cable is connected properly.
•
If the printer on a network is not detected, make sure that the printer is turned on, then select
Refresh . It may take several minutes to detect printers. If the printer is not yet detected, connect
the machine...

Maintenance...Displays the  Maintenance  screen to revert the network settings of the printer to factory default
and to mount the card slot as the network drive.
Maintenance Screen
Set up printer's wireless LAN... You can change the access point mode settings. Perform settings following the message on thescreen.
If you change the  Encryption Method:  setting and the Password: setting on the  Set up printer's
wireless LAN  screen, the changed settings are applied to the printer settings.
Note
•...

Status ScreenYou can check the printer status and connection performance.
To display the  Status screen, select  Status from the  View menu.
Note
•
This screen is not available depending on the printer you are using.
•
When using wired LAN,  Signal Strength:, Link Quality:  and Advanced Measurement...  are not
available.
1.
Device Status:
The device status is displayed as  Available or Unavailable .
2.
Signal Strength:
Indicates the strength of the signal received by the printer, ranging from 0% to...

Connection Performance Measurement Screen
Note
•
This screen is not available depending on the printer you are using.
Displays to execute the connection performance measurement.
Connection Performance Measurement Screen (Initial Screen)
Connection Performance Measurement Screen (Completion Screen)
Connection Performance Measurement Screen (Initial Screen)Click  Next>  to start measurement.
Connection Performance Measurement Screen (Completion Screen)
Displays when the measurement is finished.
335 

1.Connection Performance between the Printer and the Access Point:
A mark indicates the result of the connection performance measurement between the printer and the access point.
: Good connection performance
: Unstable connection performance
: Cannot connect
: Measurement is canceled, or cannot measure
2.
Remeasurement
Measures the connection performance again.
Note
•
If any messages appear on  Overall Network Performance: , move the machine and access point as
instructed to improve the performance.
336 

Maintenance ScreenDisplays to perform  Setting Initialization  and Network Setup of the Card Slot .
To display the  Maintenance screen, select  Maintenance...  from the Settings menu.1.
Setting Initialization
Reverts all the network settings of the printer to factory default. Click  Initialize to display the  Initialize
Settings  screen and click  Yes to initialize the network settings of the printer. Do not turn off the printer
during initialization. Click  OK when initialization is complete.
Performing...

Network Setup of the Card Slot Screen
Note
•
This screen is not available depending on the printer you are using.
Displays settings of the card slot and allows you to map a card slot on the network as a network drive on the
computer.
Displays when you click  Setup on the  Maintenance  screen.
Network Setup of the Card Slot Screen (Setup Screen)
Network Setup of the Card Slot Screen (Setup Failed Screen)
Note
•
You can change the network settings of the printer using IJ Network Tool with USB connection...

1.
Skip
Completes the setup without mapping a network drive to the card slot.
2.
Retry
Returns to  Network Setup of the Card Slot  screen and re-executes the network drive mapping.
3.
Cancel
Cancels the card slot setup. When IJ Network Tool is running over LAN, the  Cancel button is
displayed grayed out and cannot be clicked.
339 

Associate Port ScreenAllows you to associate a created port with a printer driver.
Select the printer for which you want to change the association, then click  OK.
Note
•
You cannot print with the printer unless the printer driver is associated with the port.
1.
Model:
Displays the name of device specified as a destination port.It is blank if the name of device is not detected.
2.
Printer:
Displays the printer driver installed in the computer. Select the printer for which you want to change the...