Canon printer imageCLASS MF249dw User Manual

Network
Network..............................................................................................................................................................  314
ConnectingtoaNetwork .................................................................................................................................. 315
Selecting Wired LAN or Wireless LAN (MF249dw / MF247dw)  .......................................................................  317
Connecting to a Wired LAN...

Network
1469-061
The machine has been designed for  5exibility of use across a variety of environments, and it includes advanced
technologies in addition to basic network features. Do not worry if you are not a network expert, because the machine
has also been designed for convenience and ease of use. Relax and proceed with the network setup one step at a time.
	C Connecting to a Computer/Viewing the Machine's Network Settings
 ConnectingtoaNetwork(P.315)ViewingNetworkSettings(P.344)
	C...

ConnectingtoaNetwork
1469-062
When connecting the machine to a wired or wireless local area network (LAN), you need to set an IP address unique to the selected network. Select "wired" or "wireless" depending on your communication environment and networkingdevices. For steps to connect the machine and set an IP address, see "Getting Started" ( 
ManualsIncludedwiththe
Machine(P.660) ). For speci4c  IP address settings, contact your Internet service provider or Network...

	To  connect  to  an  IEEE  802.1X  network,  see Con4gurLng  IEEE 802.1X
Authentication(P.429) . 
 
SelectwiredorwirelessLAN.
SelectingWiredLANorWirelessLAN(MF249dw/MF247dw)(P.317) 
ConnecttoawiredorwirelessLAN.
	 Proceed to the section that corresponds to the setting you selected in step 2.
ConnectingtoaWiredLAN(P.318)
ConnectingtoaWirelessLAN(MF249dw/MF247dw)(P.319)
 
 
SettheIPaddressasnecessary.
	 This step is required when you want to assign a  speci4c...

SelectingWiredLANorWirelessLAN
1469-063
After you decide on wired or wireless LAN to connect the machine to the computer, select wired LAN or wireless LAN using the operation panel. For how to connect to and specify settings for a wireless LAN/wired LAN, see "GettingStarted" ( 
ManualsIncludedwiththeMachine(P.660) ). Note that if you change the setting from  to
 or vice versa, you will need to uninstall MF Drivers installed on your computer and then reinstall them. For more...

ConnectingtoaWiredLAN
1469-064
Connect the machine to a computer via a router. Use a LAN cable to connect the machine to the router.
1ConnectaLANcable.
	 Connect the machine to a router by using a LAN cable.
	 Push the connector in until it clicks into place.
2Waitapproximately2minutes.
	While you wait, the IP address is set automatically.
You can set the IP address manually. SettingIPAddresses(P.336)
LINKS
ConnectingtoaNetwork(P.315)
Network
318       

ConnectingtoaWirelessLAN
1469-065
Wireless routers (or access points) connect the machine to a computer via radio waves. If your wireless router is equipped with Wi-Fi Protected Setup (WPS),  con4guring your network is automatic and easy. If your networking
devices do not support automatic  con4guration, or if you want to specify authentication and encryption settings in
detail, you need to manually set up the connection. Make sure that your computer is correctly connected to the network....

	CPush Button Mode
Find the WPS mark shown below on the package of your wireless router. Also make sure that there is a WPS button on your networking device. 
SettingUpConnectionUsingWPSPushButtonMode(P.321)
	C PIN Code Mode
Some WPS routers do not support the push button mode. If WPS PIN code mode is mentioned on the package or in the instruction manuals of your networking device, set up the connection by entering the PIN code. 
SettingUp
ConnectionUsingWPSPINCodeMode(P.323)
If the...

SettingUpConnectionUsingWPSPushButtonMode
1469-066
If your wireless router supports WPS push button mode, you can easily set up a connection with a WPS button.
How to operate the wireless router may vary on each device. See the instruction manuals for your networking
device for help.
1TapintheScreen.2Tap.
	 If a screen for entering a PIN is displayed, enter the PIN with the numeric keys and tap .  Setting
theSystemManagerPIN(P.397)
3Tap.
	 If the  message is displayed, tap .
	 If the...

	Depending on the networking device, you may need to press and hold the button for 2 seconds or longer.
See the instruction manuals for your networking device for help.
IfanerrormessageisdisplayedduringsetupTap  and return to step 5.
8CheckthattheWi-Fiindicatorisblinkingontheoperationpanel.
	 The Wi-Fi indicator blinks when a wireless router is detected.
	When the setup is completed, the screen below is displayed, and approximately 2 seconds later, the Wi-Fi
indicator lights up.
	...