Canon Pixma Mp980 Quick Start Guide

							
  
5
H
K
D
F
6
On the Canon IJ Network Scanner Selector 
screen, select Canon MP980 series Network in 
TWAIN Data Source Name and the MAC address 
of the machine in Network Device List, then click 
Apply to use the machine as a scanner.
To confirm the machine's MAC address, refer to "Troubleshooting" in the on-screen manual: Advanced Guide available via Solution Menu. 
With Mac OS X v.10.5.x, the Card Slot is not available when using the machine over a ne\
twork.
•
•
Confirm that a check mark is displayed, then 
click Exit to close the dialog box.
Macintosh
Next, read "22 Loading 
Paper" on page 58!
 
						

							
0
(A)21
G
H
3
20
If your access point supports WPS 
(Wi-Fi Protected Setup), you can set 
the wireless LAN security easily.
Use the Easy-Scroll Wheel (A) or the [ or 
] button to select Settings, then press the 
OK button.
Select Device settings, 
then press the OK 
button.
WPS Connection
Setup the Machine and the Computer
Select LAN settings, then 
press the OK button.
 
						

							
  
5647
G
H
Select Wireless LAN active, 
then press the OK button.
Select Change wireless/
wired, then press the OK 
button.
Select Wireless LAN 
settings, then press the OK 
button.
Select WPS settings, then 
press the OK button.
Windows／Macintosh
 
						

							

1098
G
H
20
To use the PIN code method for setup, select PIN method on step , then press the OK button. Follow the on-screen is instructions to operate the machine and access point. When the setup is complete, the completion screen appears then the LAN settings screen returns. A timeout error occurs if setup is not completed within 10 minutes. If the timeout error screen appears, refer to "5.12 The Timeout error screen is displayed during WPS setup" in the printed manual: Network Setup Troubleshooting.
•
Select Push button 
method, then press the 
OK button.
Press the OK button.When the access point is ready, press the OK button on the machine, then press the 
WPS button on the access point within two minutes.
The completion screen appears on the LCD of the machine, then the LAN settings screen returns.
Windows／Macintosh
Next, read "Install the Software" !
Windows
Macintosh
(P.15)8
Step  (P.34)1 4
A timeout error occurs if setup is not completed within two minutes. When\
 the timeout error screen appears, refer to "5.12 The Timeout error screen is displayed during WPS setup" in the printed manual: Network Setup Troubleshooting.
•
The WPS button may be named differently depending on your access point. For details, refer to the manual of your access point.•
 
						

							
  
12
I
21
The machine supports "WCN-UFD".•
You can set the wireless LAN 
security on the machine easily by 
using the WCN (Windows Connect 
Now) function of Windows Vista 
together with a USB flash drive.
Canon assumes no responsibility for any damage or loss of stored data regardless of the cause.
If your USB flash drive cannot be attached to the direct print port of the machine, an extension cord for USB flash drives may be required. Purchase one at an electronics shop.
Operation may not be guaranteed depending on your USB flash drive.
USB flash drives with security enabled may not be used.
•
•
•
•
From the Start menu of the Windows side, 
click Network.
Click Add a wireless device on the menu.
The Network folder opens.
The Add a wireless device to the Network 
screen will be displayed.
WCN Connection
Setup the Machine and the Computer 
Windows
 
						

							

54
I
3
21
Click Add the device or computer using a 
USB flash drive.
From the list, select the network name (SSID), 
then click Next.
Click I want to add a wireless device or 
computer that is not on the list, using a USB 
flash drive.
If the User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue.
•
 
						

							
  
I
67
Connect the USB flash drive to the computer, confirm that the 
drive name is displayed, then click Next.
When the above screen appears, remove the USB flash drive 
from the computer, then click Close.
Windows
 
						

							

(A)1011
I
9
21
8
Use the Easy-Scroll Wheel (A) or the [ or ] 
button to select Settings, then press the OK 
button.
Select Device settings, then 
press the OK button.
Select LAN settings, then press 
the OK button.
Select Change wireless/
wired, then press the OK 
button.
 
						

							
  
1415
I
1312
Select Wireless LAN 
active, then press the OK 
button.
Select Wireless LAN 
settings, then press the 
OK button.
Select WCN settings, 
then press the OK button.
Connect the USB flash drive to the direct print port 
(USB connector) on the front of the machine, then 
press the OK button.
The completion screen appears on the LCD of the 
machine, then the LAN settings screen returns. Remove 
the USB flash drive from the machine.
Next, read "8 Install the Software" on page 15!
Windows
 
						

							

(A)
(F)
(E)(A)
(B)
(C)
(D)
123
22
This section explains how to 
load paper in the Cassette (A) 
and the Rear Tray (B).
The Cassette (A) supports plain 
paper (C) only. To print Photo 
Paper / Hagaki (D), be sure to 
load it in the Rear Tray (B).
L o a d   i n   t h e   C a s s e t t e
Move the Paper Guides (E) and (F) 
to both edges.
Pull out the Cassette (A).Load paper.
Load paper with the printing side facing down.•
Loading Paper