Canon Pixma Mp980 Quick Start Guide

							
  
12
C
10
First-time Setup for Use over Wired LAN
Setup the Machine and the Computer
Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to “7 Machine's LAN Setting” on page 14.•
When a confirmation screen for the machine's LAN setting appears, click 
OK.
Windows
Confirm that USB Cable and LAN Cable are Ready.
P r e p a r e   C a b l e s
On the Setup Method screen, select Connect printer to the 
network for the first time, then click Next.
USB CableLAN Cable
 
						

							
0
USB
3
C
4
10
When the Printer Connection screen appears, connect the machine to the computer with 
a USB cable, then turn on the machine.
Set up the machine over a USB connection until the network connection is complete.
When the Setup Preparations dialog box appears, 
confirm that preparation is complete, then click Next.
The machine is recognized by the computer, then message appears on the screen.
If you cannot go to the next procedure after 10 minutes, click Help and confirm the message.
•
•
The USB port is located on the right side at the back of the machine.•
 
						

							
  
USB
(A)
5
C
6
Connect the machine to the 
network device with a LAN cable 
(A), then click Yes.
Windows
Windows Vista
Windows XP/2000
D e t e c t   t h e   M a c h i n e
If no connection is established even after Connect is clicked, refer to "5.6 The Set Printer IP Address dialog box is displayed during setup" in the printed manual: Network Setup Troubleshooting.
•
When the Set Printer IP Address screen 
appears, click Connect.
If the machine is detected automatically, the Set 
Printer IP Address screen does not appear. Go 
to the following procedure.
Go to Step .
Go to Step .
 
						

							

USB
7
C
10
8
Windows
Windows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify 
the drive letter, then click Next.
If the error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting.•
When the Setup Completion dialog box appears, remove the USB 
cable, then click Finish.
Next, read "13 Information" on page 31!
To change the port name, click View Setup Results, then click Set Port Name. For details, refer to "8 Changing the port name" in the printed manual: Network Setup Troubleshooting.
If Unsafe Removal of Device is displayed, click OK.
•
•
 
						

							
  
USB
21
E
11
On the Setup Method screen, select 
Connect printer to the network for the 
first time, then click Next.
Set the machine's LAN setting to Wireless LAN active beforehand. For details, refer to “7 Machine's LAN Setting” on page 14.
•
When a confirmation screen for the machine's 
LAN setting appears, click OK.
First-time Setup for Use over Wireless LAN
Setup the Machine and the Computer
Windows
Set up the machine over a USB connection until the network connection is complete.
When the machine is recognized by the computer, a message appears on the screen.
If you cannot go to the next procedure after 10 minutes, click Help and confirm the message.
•
•
The USB port is located on the right side at the back of the machine.•
When the Printer Connection screen appears, connect the machine to the computer 
with a USB cable, then turn on the machine.
 
						

							

34
E
11
When the Setup Preparations 
dialog box appears, confirm that 
preparation is complete, then click 
Next.
D e t e c t  A c c e s s   P o i n t
When the Access Points screen appears, select an access point to use, then click Connect.
When an access point is detected automatically, the Access Points screen does not appear. Go to step .
To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Key, then click Connect. For details on network keys, refer to "3.1 About Network Key (Windows)/Network Password (Macintosh)" in the printed manual: Network Setup Troubleshooting.
•
If you want to select an access point manually, or if the target access point is not displayed in the list, or if an e\
rror message appears, refer to “5 The following screen is displayed during setup” in the printed manual\
: Network Setup Troubleshooting.•
 
						

							
  
56
E
Windows
If no connection is established even after Connect is clicked, refer to "5.6 The Set Printer IP Address dialog box is displayed during setup" in the printed manual: Network Setup Troubleshooting.
•
When the Set Printer IP Address screen appears, click 
Connect.
If the machine is detected automatically, the Set Printer 
IP Address screen does not appear. Go to the following 
procedure.
D e t e c t   t h e   M a c h i n eWindows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify 
the drive letter, then click Next.
If the error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting.•
Windows Vista
Windows XP/2000
Go to Step .
Go to Step .
 
						

							

USB
78
E
11
When the Setup Completion dialog box appears, remove the USB cable, 
then click Next.
To change the port name, click View Setup Results, then click Set Port Name. For details, refer to "8 Changing the port name" in the printed manual: Network Setup Troubleshooting.
If Unsafe Removal of Device is displayed, click OK.
•
•
Turn off the machine, then place the machine in the location where you 
will use it, and turn on it.
 
						

							
  
910
E
Measuring takes a few minutes. You can cancel measuring by clicking Cancel. You also examine the detailed status of the communication link after setu\
p by using the Canon IJ Network Tool. For details, refer to the on-screen manual: Advanced Guide.
•
On the Connection Performance Measurement screen, click Next.
Measuring of the communication status starts, and the results are displayed.
If any symbol other than  is displayed, refer to displayed comments and Help for improving the status of communication link.
To check whether the new location is better, click Remesurement. Measurement of the communication status is performed again.
When any message on Overall network performance appears in the measurement results, rearrange the printer and other network devices fol\
lowing the instructions on the screen.
•
•
•
Confirm the measurement results, then click Finish.
Ensure that  is displayed in Connection performance between the printer and 
the access point.
Next, read "13 Information" on page 31!
Windows
 
						

							

(A)
21
G
I
J
12
Connect the Wired LAN / Wireless LAN
Setup the Machine and the Computer
Press the ON button (A) to TURN ON THE MACHINE.
Make sure that the computer you are setting up is not connected to the m\
achine with a USB cable.
For wired LAN connections, confirm that the machine is connected to the network with a LAN cable.
•
•
On the Setup Method screen, select Printer is already connected 
to the network, then click Next.