Canon Pixma Mp980 Quick Start Guide

Make sure to read this manual before using the machine. Please keep it in hand for future reference.
MP980
Getting Started
=Read Me First=
series
Photo All-In-One
 

S y m b o l s■
The following symbols are used to mark important instructions. Observe these instructions.
Instructions that, if ignored, could result in personal injury or material damage.
Instructions that must be observed for safe operation.
Additional explanations.
Descriptions for operations that take some time to complete.
Model Number: K10327(MP980)
Microsoft is a registered trademark of Microsoft Corporation.
Windows is a trademark or registered trademark of Microsoft Corporation \
in the U.S....

  
Contents
Unlock the Scanning Unit (Cover)
Align the Print Head
After Installing the Machine
Loading Paper
Setup the Machine and the Computer
Confirming the Setup Flow
Install the Ink Tanks
Install the Print Head
Turn the Power On
 


(B)
(C)
(A)
1
1
1
3
2
Unlock the Scanning Unit (Cover)
F i r s t ,   c h e c k   t h e   i n c l u d e d   i t e m s
Manuals
Setup CD-ROM (containing the drivers, applications and on-screen manuals)
Warranty
MP-101 paper (for Automatic Print Head Alignment)
•
•
•
•
Close the Document Cover (B).
Open the Document Cover (B).
Move the Scanner Lock Switch (C) towards the 
release mark to unlock the Scanning Unit (Cover).
Before turning on the machine, remove all the orange tapes and the protective...

  
(1)
(2)
(A)
(B)
(C)
(D)
2
231
Turn the Power On
Do NOT connect the USB cable at this stage.•
Plug in the power cord on the left 
side at the back of the machine and 
connect the other end to the wall 
outlet.
Open the Operation Panel (A), then press the ON button (B) 
to turn on the machine.
Make sure that the Document Cover (C) is closed.
If an unintended language is displayed on the LCD, press the Back button on the Operation Panel to return to the Language selection screen.
•
•
Use the { or }...


(E)
(A)
(B)
(C)
(D)
3
12
Install the Print Head
Raise the Print Head Lock Lever (E).Open the Paper Output Tray (A), then lift the 
Scanning Unit (Cover) (B) until it locks into place.
The Scanning Unit (Cover) (B) is fixed automatically.
The Print Head Holder (C) comes out. (This is where 
you install the Print Head.)
For your safety, always grip as illustrated.
Close the Document Cover (D) and lift it with the 
Scanning Unit (Cover).
•
•Firmly raise the Print Head Lock Lever until it stops. (The...

  
(E)
543
Remove the Print Head from 
the silver package.
Remove and discard the orange protective 
cap.
Tilt the Print Head and set it in place. Lower the Print Head Lock 
Lever (E) completely.
There may be some transparent or light blue ink on the inside of the bag\
 the Print Head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. Be care\
ful not to stain your hands.
•
Do not knock the Print Head...


(1)
(2)
(A)
4
12
Install the Ink Tanks
Do not hold the sides of the ink tank; ink may splash.•
Pull the orange tape (1) in the direction of the 
arrow to peel off the protective film and remove 
the film (2) completely.
If the Print Head Holder moves to the right, close and reopen the Scanning Unit (Cover).
Be sure to use the supplied ink tanks.
•
•
Do not handle the ink tanks roughly such as applying them excessive pressure or dropping them.
•
While pressing down with your left thumb, twist 
off...

  
(B)
453
Install all the other ink tanks in the same 
way.
Install all the ink tanks.
Close the Scanning Unit (Cover) (B).
Wait until the screen above appears (about 6 
minutes) and go to the next step.
The machine may make some operating noises 
when preparing to print. This is normal operation.
•
•
Once you have installed the ink tanks, do not remove them unnecessarily.•
Make sure all the Ink lamp lights red.•
For your safety, always grip as illustrated.•
If an error message is displayed on the...


(C)(C)
(A)
(B)
5
21
Align the Print Head
Align the Print Head for better print results. 
This takes about 7 minutes.
Use a sheet of supplied speciality paper 
(MP-101) for alignment.
Make sure that the Output Tray Extension (B) is extended.•
Open the Paper Support (A) and pull it out.Move the Paper Guides (C) to both edges.