Canon Pixma Mp630 User Guide

Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Part of the Page Is Not Printed
Part of the Page Is Not Printed
Check: When performing automatic duplex printing, the reason below is
possible.
When performing automatic duplex printing, the printable area at the top of the page will be 0.08
inches / 2 mm narrower than the usual.
For this reason, the bottom of the page may not be printed. To prevent this, select Use reduced
printing from the printer driver.
Important
Reduced printing may...

Advanced Guide > Troubleshooting > Print Results Not Satisfactory > No Printing Results/Printing Is Blurred/Colors Are
Wrong/White Streaks
No Printing Results/Printing Is Blurred/Colors Are Wrong/White
Streaks
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Check the status of ink tanks. Replace the ink tank if the ink
Page 712 of 805 pages No Printing Results/Printing Is Blurred/Colors Are Wrong/White Streaks
 

has run out.
Routine Maintenance
Check 3: Is the orange tape or protective film remaining?
Make sure that all of the protective film is peeled off and the air hole is exposed, as illustrated in (A).
If the orange tape is left as in (B), pull the orange tape and remove it.
Check 4: Print the Nozzle Check Pattern and perform any necessary
maintenance operations such as Print Head Cleaning.
Print the Nozzle Check Pattern to determine whether the ink ejects properly from the print head
nozzles.
Refer to...

Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Lines Are Misaligned
Lines Are Misaligned
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Perform Print Head Alignment
If you did not align the Print Head after installation, straight lines may be printed misaligned. Be sure
to align the Print Head after you install it.
Routine Maintenance
Note
If the problem is not resolved after performing the Print Head Alignment, perform Print...

Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Printed Paper Curls or Has Ink Blots
Printed Paper Curls or Has Ink Blots
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: If Intensity is set high, reduce the Intensity setting in the printer
driver and try printing again.
If you are using plain paper to print images with high intensity, the paper may absorb too much ink
and become wavy, causing paper abrasion.
When printing from...

Advanced Guide > Troubleshooting > Print Results Not Satisfactory
 > Paper Is Smudged/Printed Surface Is Scratched
Paper Is Smudged/Printed Surface Is Scratched
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Is the appropriate type of paper used? Check the followings:
Check to see if the paper you are printing on is suitable for your printing purpose.
Loading Paper / Originals
When performing Borderless Printing, make sure that the paper you are...

We recommend printing curl-corrected paper one sheet at a time.
Note
Depending on the media type, the paper may be smudged or may not be fed properly even if it
is not curled. In such cases, follow the procedure described above to curl the paper before
printing. This may improve the print result.
Check 4: If you are printing on thick paper, select the Prevent paper
abrasion setting.
Selecting the Prevent paper abrasion setting will widen the clearance between the Print Head and
the loaded paper. If you...

1.Open the Print dialog box.
Opening the Page Setup and Print Dialog Box (Macintosh)
2.Select Color Options in the pop-up menu.
3.Drag the Intensity slide bar to set the intensity.
When copying
Setting Items
Check 6: Is printing performed beyond the recommended printing area?
If you are printing beyond the recommended printing area of your printing paper, the lower edge of
the paper may become stained with ink.
Resize your original document in your application software.
Printing Area
Check 7: Is the...

2.Open the Canon IJ Printer Utility.
Opening the Canon IJ Printer Utility (Macintosh)
3.Select Custom Settings in the pop-up menu.
4.Drag the Ink Drying Wait Time slide bar to set the wait time, and then click Send.
5.Confirm the message and click OK.
Check 11: Is the paper scratched by other loaded paper?
Depending on the media type, the paper may be scratched with other loaded paper when feeding
from the Rear Tray. In this case, load one sheet at a time.
Page top
Page 719 of 805 pages Paper Is...

Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Back of the Paper Is Smudged
Back of the Paper Is Smudged
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Perform the Bottom Plate Cleaning to clean the inside of the
machine.
Cleaning the Inside of the Machine (Bottom Plate Cleaning)
Note
When performing duplex printing or too much printing, the inside may become stained with ink.
Page top
Page 720 of 805 pages Back of the Paper Is...