Canon Pixma Mp620 Quick Start Guide

  
(A)
USB
5
C
6
Connect the machine to the 
network device with a LAN cable 
(A), then click Yes.
Windows
Windows Vista
Windows XP/2000
D e t e c t   t h e   M a c h i n e
If no connection is established even after 
Connect is clicked, refer to "5.6 The Set Printer 
IP Address dialog box is displayed during 
setup" in the printed manual:  Network Setup 
Troubleshooting .
•
When the 
Set Printer IP Address  screen 
appears, click  Connect.
If the machine is detected automatically, the...

0
USB
7
C
9
8
Windows
Windows XP/2000
When the  Network Setup of the Card Slot  dialog box appears, specify 
the drive letter, then click  Next.
If the error message appears, refer to "5 The following screen is displayed 
during setup" in the printed manual:  Network Setup Troubleshooting.
•
When the 
Setup Completion  dialog box appears, remove the USB 
cable, then click  Finish.
Next, read "12 Information" on page 29!
To change the port name, click  View Setup Results, then click...

  
USB
21
E
10
On the Setup Method  screen, select 
Connect printer to the network for the 
first time , then click  Next.
Set the machine's LAN setting to Wireless 
LAN active beforehand. For details, refer to 
“6 Machine's LAN Setting” on page 12.
•
When a confirmation screen for the machine's 
LAN setting appears, click 
OK.
First-time Setup for Use over Wireless LAN
Setup the Machine and the Computer
Windows
Set up the machine over a USB connection until the network connection...


34
E
10
When the Setup Preparations  
dialog box appears, confirm that 
preparation is complete, then click 
Next .
D e t e c t  A c c e s s   P o i n t
When the  Access Points  screen appears, select an access point to use, then click  Connect.
When an access point is detected automatically, the  Access Points screen does not appear. Go to step .
To connect to the access point with  WEP or WPA displayed in the Encryption column, enter the network key (WEP key or 
WPA key) in  Network Key ,...

  
56
E
Windows
If no connection is established even after Connect is 
clicked, refer to "5.6 The Set Printer IP Address dialog box is 
displayed during setup" in the printed manual:  Network Setup 
Troubleshooting .
•
When the 
Set Printer IP Address  screen appears, click 
Connect .
If the machine is detected automatically, the  Set Printer 
IP Address  screen does not appear. Go to the following 
procedure.
D e t e c t   t h e   M a c h i n eWindows XP/2000
When the  Network Setup of...


USB
78
E
10
When the Setup Completion  dialog box appears, remove the USB cable, 
then click  Next.
To change the port name, click  View Setup Results, then click Set Port Name. 
For details, refer to "8 Changing the port name" in the printed manual: 
Network Setup Troubleshooting .
If  Unsafe Removal of Device  is displayed, click OK.
•
•
Turn off the machine, then place the machine in the location where you 
will use it, and turn on it.
 

  
910
E
Measuring takes a few minutes. You can cancel measuring by clicking Cancel. 
You also examine the detailed status of the communication link after setu\
p by 
using the Canon IJ Network Tool. For details, refer to the on-screen manual: 
Advanced Guide.
•
On the 
Connection Performance Measurement  screen, click Next.
Measuring of the communication status starts, and the results are displayed.
If any symbol other than 
 is displayed, refer to displayed comments and Help 
for improving...


(A)
21
G
I
J
11
Connect the Wired LAN / Wireless LAN
Setup the Machine and the Computer
Press the ON button (A) to TURN ON THE MACHINE.
Make sure that the computer you are setting up is not connected to the m\
achine with a 
USB cable.
For wired LAN connections, confirm that the machine is connected to the network with a 
LAN cable.
•
•
On the 
Setup Method  screen, select Printer is already connected 
to the network , then click Next.
 

  
3
G
I
J
Windows
Some programs that switch the network environment depending on your environment will enable a firewall by default. Check the settings of any such software.
•
When the  Printers screen appears, make sure that the machine is selected and click  Next.
When the machine is not detected, make sure of the following, click  Update.
•
The machine is turned on.
When using wireless LAN : The computer is connected to the access point.
When using wired LAN : The machine is connected to...


5
G
I
J
11
4
Windows
Windows XP/2000
When the  Network Setup of the Card Slot  dialog box appears, specify the drive 
letter, then click  Next.
If the error message appears, refer to "5 The following screen is displayed during setup" 
in the printed manual:  Network Setup Troubleshooting .
• To change the port name, click 
View Setup Results, then click Set 
Port Name. For details, refer to "8 Changing the port name" in the 
printed manual:  Network Setup Troubleshooting .
•...