Canon Pixma Mp620 Quick Start Guide

							Make sure to read this manual before using the machine. Please keep it in hand for future reference.
MP620
Getting Started
=Read Me First=
series
Photo All-In-One
 
						

							S y m b o l s
■
The following symbols are used to mark important instructions. Observe these instructions.
Instructions that, if ignored, could result in personal injury or material damage.
Instructions that must be observed for safe operation.
Additional explanations.
Descriptions for operations that take some time to complete.
Model Number: K10325(MP620)
Microsoft is a registered trademark of Microsoft Corporation.
Windows is a trademark or registered trademark of Microsoft Corporation \
in the U.S. and/or other countries.
Windows Vista is a trademark or registered trademark of Microsoft Corporation in \
the U.S. and/or other countries.
Macintosh, Mac, and AirPort are trademarks of Apple Inc., registered in the U.S. and other countries.
Wi-Fi is a registered trademark of the Wi-Fi Alliance. 
The Wi-Fi CERTIFIED logo is a certification mark of the Wi-Fi Alliance.
•
•
•
•
•
 
						

							  
Contents
Check the Included ItemsTurn the Power OnInstall the Print Head Install the Ink Tanks
Setup the Machine and the ComputerLoading Paper
Confirming the Setup Flow
After Installing the Machine
 
						

							
(A)
1
Manuals
Setup CD-ROM (containing the drivers, applications and on-screen manuals)
Warranty
•
•
•
Check the Included Items
Before turning on the machine, remove all the orange tapes and the prote\
ctive sheets.
•
Open the Paper Output Tray with your hands, and take out the Print Head. The Print Head is placed inside of the Paper Output Tray (A).
ink tank Print Head
power cord USB cable
The USB cable is used during the 
network setup procedure.
 
						

							  
(A)
(B)
(C)
(D)
(1)
(2)
2
231
Turn the Power On
Do NOT connect the USB cable at this 
stage.
•
Plug in the power cord on the left 
side at the back of the machine and 
connect the other end to the wall 
outlet. Open the Operation Panel (A), then press the 
ON button (B) 
to turn on the machine.
Make sure that the Document Cover (C) is closed.
If an unintended language is displayed on the LCD, press the  Back button on the Operation Panel to return to the 
Language selection  screen.
•
•
Use the 
{ or
 }  button (D) on the 
Operation Panel to select the language 
for the LCD, then press the  OK button. 
The standby screen is displayed.
The machine may make some operating noises. This is normal operation.
•
 
						

							
(E)
(A)
(B)
(C)
(D)
3
12
Install the Print Head
Close the Document Cover (D) and lift it with the 
Scanning Unit (Cover).
•
Firmly raise the Print Head Lock Lever until it stops. (The 
Print Head Lock Lever may feel heavy.)
•
If the Print Head Holder does not move, make sure that the 
machine is turned on.
•
Open the Paper Output Tray (A), then lift the 
Scanning Unit (Cover) (B) until it locks into place.
Raise the Print Head Lock Lever (E).
Do not handle the Print Head 
roughly such as applying them 
excessive pressure or dropping 
them.
•
The Print Head Holder makes a noise as it moves. 
This is normal operation.
•
The Scanning Unit (Cover) (B) is fixed automatically.
The Print Head Holder (C) comes out. (This is where 
you install the Print Head.)
 
						

							  
(E)
543
Remove the Print Head from the 
silver package.Remove and discard the orange 
protective cap. Tilt the Print Head and set it in place. Lower the Print Head Lock Lever 
(E) completely.
There may be some transparent or light blue ink on the inside of the bag\
 the Print 
Head comes in, or the inside of the protective cap - this has no effect on print 
quality. Be careful not to get ink on yourself when handling these items. Be ca\
reful 
not to stain your hands.
•
Do not knock the Print Head against the sides of the Holder.
Be sure to install it in a well-lit environment.
Pinch the Print Head Lock Lever firmly and lower it gently.
Once you have installed the Print Head, do not remove it unnecessarily.
•
•
•
•
 
						

							
(A)
(1)
(2)
4
12
Install the Ink Tanks
Do not hold the sides of the ink tank; ink may splash.
•
Pull the orange tape (1) in the direction of the 
arrow to peel off the protective film and remove 
the film (2) completely.
If the Print Head Holder moves 
to the right, close and reopen 
the Scanning Unit (Cover).
Be sure to use the supplied ink 
tanks.
•
• Do not handle the ink tanks 
roughly such as applying them 
excessive pressure or dropping 
them.
•
While pressing down with your left thumb, twist off the 
orange protective cap (A) located on the bottom of the 
ink tank.
 
						

							  
(B)
453
Wait until the screen above appears (about 4 
minutes) and go to the next step.
The machine may make some operating noises 
when preparing to print. This is normal operation.
•
•
If an error message is displayed on the LCD, make 
sure that the Print Head and the ink tanks are correctly 
installed.
•
Install all the other ink tanks in the 
same way.
Install all the ink tanks.
Make sure all the  Ink lamp lights red.
• Once you have installed the ink tanks, 
do not remove them unnecessarily.
•
Close the Scanning Unit (Cover) (B).
Press the  PUSH mark on the ink 
tank until it clicks into place.
Make sure the  Ink lamp lights red.
I n s t a l l   t h e   I n k   Ta n k
Be sure to install it in a well-lit 
environment.
•
Match the labels when installing.
•
 
						

							
(C)
4
76
Press the OK button.
For details, refer to "21 Loading Paper" on page 56.
Close the Paper Output Tray to make it easier to pull out the 
Cassette.
•
• For better print results, it is recommended that you align the Print Hea\
d before printing photos. To 
align the Print Head, use the 
{ or 
} button to select Perform head alignment, then press the OK 
button. Follow the steps in "Align the Print Head" on page 67 for alignm\
ent.
You can perform Print Head Alignment at any time. For details, refer to the on-screen manual:  Basic 
Guide.
•
•
Load three or more sheets of A4 or Letter-sized plain 
paper into the Cassette (C), then press the 
OK button.
Confirm that the above screen appears.