Canon network camera VBR13 User Manual

Setting Page
5
211
Settings for using IPsec.
Note
If IPsec is used, video transmission performance drops.
IPsec
[IPsec]
Select the key exchange method when using IPsec.
Auto Key Exchange Settings
[IPsec SA Encryption Algorithm]
Select the IPsec SA encryption algorithm.
The specified algorithm will be checked for an app licable encryption algorithm starting from the left.
[IPsec SA Authentication Algorithm]
Select the IPsec SA authentication algorithm.
[Security] > [IPsec]
Setting IPsec
Important
 To run...

212
The specified algorithm will be checked for an applicable authentication algorithm starting from the left.
[IPsec SA Validity Period (min)]
Enter the duration of validity for IPsec SA.
[ISAKMP SA Encryption Algorithm]
Select the SA encryption algorithm for use with auto key exchange protocol IKE.
[ISAKMP SA Authentication Algorithm]
Select the SA authentication algorithm for  use with auto key exchange protocol IKE.
[DH Group]
Select the key generation information that  will be used in the DH...

Setting Page
5
213
[IPsec Mode]
Select the IPsec mode.
[Destination IPv4 Address], [Destination IPv6 Address]
Enter the IP address of the connection destination.
[Source IPv4 Address], [Source IPv6 Address]
Enter the IP address of the source.
[Security Protocol]
Select the IPsec protocol.
If you select [ESP], enter only the setting items relating to ESP.
If you select [AH], enter only the setting items relating to AH.
If you select [ESP and AH], enter all setting items.
[Security Gateway IPv4 Address],...

214
[SA AH Authentication Key (outbound)]
Enter the SA authentication key for outbound.
If [HMAC_SHA1_96] or [HMAC_MD5_96] was selected in [SA AH Authentication Algorithm], set a 160-bit or 128-bit 
hexadecimal number, respectively.
[SA AH SPI (outbound)]
Enter the SA SPI value for outbound.
Set a desired value in the range of 256 to 4294967295.
[SA AH Authentication Key (inbound)]
Enter the SA authentication key for inbound.
If [HMAC_SHA1_96] or [HMAC_MD5_96] was selected in [SA  AH Authentication...

Setting Page
5
215
Settings for recording video to a memory card inserted in the camera. You can also see the status of the memory card.
[Memory Card] is the same as  [Video Record] > [Memory Card]. Settings configured on one [Memory Card] page are also 
reflected on the other.
Note
 Memory card videos can be viewed and manag ed using the Recorded Video Utility. For information on operating the Recorded Video  
Utility and its downloaded data, please re fer to “Recorded Video Utility User Manual”.
 When...

216
The memory card will be automatically mounted when you insert it into the memory card slot. It will also be automatically 
mounted if it has been inserted in the memory card slot when the camera starts up.
[Mount/Unmount]
Click [Unmount] to unmount the memory card.
Be sure to unmount the memory card when turning off th e power to the camera or removing the memory card.
Also click [Mount] with the memory car d inserted to mount the memory card.
[Operation Settings]
Select the data to save to the...

Setting Page
5
217
[Delete Time]
Enter the time to delete video that has exceeded the [Days Saved] setting.
[Recreate Video Management Information]
If you click [Exec], the management information file for  recorded video will be recreated on the memory card.
The memory card cannot be accessed during this process. It  is also recommended that users not upload or stream video 
from the camera.
When recreating video management informat ion files, the more files you recreate, the longer the process will...

218
Check camera information, such as the firmware version, and perform maintenance on the camera system.
Device Information
[Model Name], [Firmware Version], [Serial  Number], [Build Number] and [MAC address]
Displays information about the camera.
Tool
You can configure/re boot the camera and display licenses.
[View Current Settings]
Display a list of current se ttings for the Setting Page.
[View License]
Display information on the th ird-party software licenses.
[Reboot]
Reboot the camera.
[Refresh...

Setting Page
5
219
[Network Settings]
If you set this to [Save], the following settings are retained when initializing.
 Administrator Name
 Password
 Network Settings
 Time Zone
 Certificates
 Private Key
If you set this to [Do not save], the above settings are also initialized.
Since the administrator account is also initialized, you will  become unable to connect to the camera. Use the Camera 
Management Tool to configure  the initial settings (P. 38).
[Revert to Initial Settings]
The initial settings...

220
You can save/restore all the camera settings.
Backup / Restore
Configure the settings regarding backup and restoring.
[Save Destination]
Select the destination for saving the camera settings when backing up.
[Back Up Settings]
All settings, except date and time, will be backed up. The administrator account, certificates used by SSL/TLS and 802.1X 
and private key will also be backed up.
[Restore Settings]
Restores all settings, except date  and time, from the backup file created with [Back Up...