Canon network camera VBC60 User Manual

1-45
IPsec Settings (IPsec)
1
1Detailed Settings
(6) [Security Gateway Address (IPv4/IPv6)]
If the IPsec operation mode was set to [ Tunnel Mode] in (2), set the IP address of the security 
gateway.
(7) [Destination Prefix Length] This setting is required only when the IPsec operation mode was set to [ Tunnel Mode] in (2).
Enter a desired prefix length for connection destination in a range of 0 to 128.
If IPv4 is used, enter a desired length in a range of 0 to 32.
„ If [ ESP ] or [ ESP and AH ] was set...

1-46
IPsec Settings (IPsec)
(10)[SA ESP Encryption key (outbound)]
Set the SA encryption key for outbound. If [AES], [3DES ] or [DES] was selected in (8), set a 
128-bit, 192-bit or 64-bit hexadecimal, respectively. This item need not be set if [ NULL] was 
selected.
(11)[SA ESP Authentication key (outbound)]
Set the SA authentication key for outbound. If [ HMAC_SHA1_96] or [HMAC_MD5_96] was set in 
(9), set a 160-bit or 128-bit hexadecimal, respectively. This item need not be set if [ No...

1-47
IPsec Settings (IPsec)
1
1Detailed Settings
„
If [ AH ] or [ESP and AH ] was set under [Security Protocol ] in (5), the following items must be 
set.
(16)[SA AH Authentication Algorithm]
Select [ HMAC_SHA1_96 ] or [HMAC_MD5_96] as the AH authentication algorithm according 
to the authentication algorithm supported by the device to connect to.
(17)[SA AH Authentication key (outbound)]
Set the SA authentication key for outbound. If [ HMAC_SHA1_96] or [HMAC_MD5_96 ] was set in 
(16), set a 160-bit or...

1-48
Setting the Items Requiring Rebooting (Reboot Item)
(1) [LAN]IP address and other settings required for LAN Connection (  P. 1-8)
(2) [IPv6] Settings relating to use of IPv6 (  P. 1-9)
(3) [Installation Conditions] Settings relating to camera installation conditions (  P. 1-20)
(4) [MPEG-4] Settings relating to video size and frame rate in MPEG-4 (  P. 1-23)
(5) [HTTP Server] HTTP port number settings (  P. 1-33)
The following items that require rebooting, if changed, are gathered here.
z
LAN,...

1-49
Setting the Items Requiring Rebooting (Reboot Item)
1
1Detailed Settings
Note
These settings relate to network connection. If any setting is changed to a value that may 
disable camera connection from the active browser, the following dialog box appears and 
alerts the user.
To apply the new setting, click [
OK].
Depending on the new setting, it may not be possible to connect to the camera again after 
rebooting. In this case, a candidate URI is displayed as shown below,
If you want to connect to...

1-50
Viewing Event Logs and Current Settings, and 
Performing Maintenance (Maintenance) 
Tool
(1) [View Log Events]Historical data of the camera such as operati ons and connections with various viewers, etc., 
is shown.
(2) [View Current Settings] A list of current settings is shown.
(3) [Reboot] The camera is rebooted.
(4) [Restore Settings] All setting items of this camera, except for the Administrator password, network settings (IP 
address setting, IP address, subnet mask, default gateway), date &...

VBAdmin Tools
How to set the camera using VBAdmin Tools is explained. You can 
create panorama images, set view restrictions, set presets, set 
motion detection, view logs, and launch Admin Viewer. Set each 
item after specifying the necessary detailed settings according to 
Chapter 1. 

2-2
Overview of VBAdmin Tools
VBAdmin Tools consists of multiple applications for [Panorama Creation Tool], [View Restriction 
Setting Tool], [ Preset Setting Tool ], [Motion Detection Setting Tool ], [Log Viewer ] and [Admin 
Viewer ]. You can remotely set the camera, view priv ileged images, check the operating condition, 
acquire logs, and perform other operations with ease.
VBAdmin Tools (P. 2-6)
This is the main panel for VBAdmin Tools. You can start each tool from this panel. First, install...

2-3
Overview of VBAdmin Tools
VBAdmin Tools
View Restriction Setting Tool (P. 2-14)
A tool that lets you visually set view restrictions. You can set the desired range with the mouse by 
referring to the preview in the panorama mode. 
Preset Setting Tool (P. 2-22)
A tool that lets you visually set presets and the home position. You can specify the desired setting 
with the mouse by referring to the preview in the panorama mode. You can also set [Preset Tour] 
whereby the camera tours and monitors multiple...

2-4
Overview of VBAdmin Tools
Motion Detection Setting Tool (P. 2-34)
This tool is used to set the motion detection function that performs upload, notifies the viewer, 
records a log, etc., if a change has occurred in the captured image due to movement of a 
subject. You can set the position and size of the motion detection area, detection judgment 
conditions, etc., while checking the image on the camera.
Log Viewer (P. 2-45)
This viewer shows the logs of operating conditions output to the camera.