Canon network camera VBC60 User Manual

2-35
Motion Detection Setting Tool
VBAdmin Tools
„Display Screen of Motion Detection Setting Tool (Live Mode)
(1) [Load Motion Detection Settings] button
Clicking this button loads the current motion detection settings of the camera.
(2) [Save Motion Detection Settings] button Clicking this button saves the motion detection setting edited by this tool.
If you have set motion detection, be sure to save the settings using [
Save Motion Detection 
Settings].
(3) Live mode tab (Live/Record)
Video is...

2-36
Motion Detection Setting Tool
(6) Motion detection area frameThe range in which motion detection is performed is shown by a dotted-line frame. You can 
drag the mouse to resize/move the frame.
(7) [Start recording] button Clicking this button starts recording video.
(8) [Enable motion detection of the camera] Select this check box if you want to enable the motion detection function.
(9) Settings tabs (Camera/Area) Set the frame rate and preset position (  P. 2-37).
 [Area] Select the motion...

2-37
Motion Detection Setting Tool
VBAdmin Tools
2. Set the frame rate of the camera and a desired camera orientation used for detection ([Camera] tab   P. 2-37).
3. Set the detection area ([Area] tab,   P. 2-38)
4. Set the conditions specifying the degree of change triggering the [Detected] mode ([Area] tab,   P. 2-38).
5. Save the settings.
„ Setting Motion Detection
How to Set
1. Enable motion detection.
Select the [ Enable motion detection of the camera ] check box.
2. Set the frame rate and...

2-38
Motion Detection Setting Tool(1)Setting Frame Rate When this check box is selected, the cameras frame rate for motion detection can be 
changed. Enter a desired rate in a range of fps 0.5 to 30.0.
(2)Enable preset selection When this check box is selected, you can se lect the camera position using a preset. 
3. Set the motion detection area ([Area] tab). Up to four motion detection areas can be created, where the frame of each area can be 
resized/moved by dragging. To resize the frame, drag 
„ at...

2-39
Motion Detection Setting Tool
VBAdmin Tools
(1)Motion Detection AreaSelect the check box corresponding to the motion detection area you want to use, and the 
detection area frame will be displayed in the viewer. Up to four detection areas can be 
created.
(2)[Selected Area] If multiple motion detection area frames have been created, a separate motion detection 
level can be set for each area frame.
Next, set the name of the selected area. (The area name can be omitted.)
Up to 15 ASCII characters...

2-40
Motion Detection Setting Tool(6)[Size]The camera mode will change to [ Detected] if the ratio of the area in which change has 
been detected (red or yellow rectangle) to the area of the selected active detection area 
frame (frame indicated by blue solid lines) exceeds the value set here (  P. 2-42). 
However, the mode will not change to [ Detected] even when the set value of [Size] has 
been exceeded, if the change has not continued for the duration in seconds set in 
[Duration]. Set a desired...

2-41
Motion Detection Setting Tool
VBAdmin Tools
4. Check the motion detection status of the camera.To check the level of motion detection operation based on the specified settings, select the 
[Display motion detection status of the camera ] check box. The motion detection status will be 
shown by the icons specified below.
If the [ Display motion detection status of the camera ] check box is selected, the settings 
cannot be saved. To save the settings, clear this check box.
5. Click [Save motion...

2-42
Motion Detection Setting Tool
Tip
[Detected] Mode and Display ScreenThe area frame in which the camera is 
detecting motion is displayed by blue 
solid lines in the viewer.
The area in which the camera is detecting 
motion at the specified sensitivity is 
displayed by a yellow or red rectangle 
inside the motion detection area frame.Yellow rectangle : The camera detected 
a motion, but it did not meet the [ Size] 
or [ Duration ] setting and thus the mode 
has not changed to [ Detected].
Red...

2-43
Motion Detection Setting Tool
VBAdmin Tools
If a motion corresponding to [Size] or greater has remained detected for the specified 
duration or longer, the mode changes to [ Detected] and a peak block is displayed. Even 
when the specified size becomes no longer met in the [ Detected] mode where a peak block is 
still displayed, the [ Detected] mode will be maintained for the specified duration.
Setting the Motion Detection Sensitivity While Checking the Recorded Video
To set the motion detection...

2-44
Motion Detection Setting Tool2. Adjust the camera position and click the Start recording button in the [Live] tab.
Recording of the video shown in the viewer will start. Record the video needed to adjust 
the motion detection level by creating motion in front of the camera.
To stop recording, click the Stop button.
3. Adjust the motion detection sensitivity in the [Area] tab while checking the video in the  [Video] tab.
(1)List of recorded video
A list of recorded video is shown.
(2)[Delete] button...