Canon Lbp 3460 User Guide

3-44Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
-When loading paper at a size of A4, B5, A5, Legal, Letter, or Executive or custom 
size paper in portrait orientation, load the paper so that the printing side is facing 
up as shown in the following figures.
(:  Feeding direction)
 

3-45Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
-When loading custom size paper in landscape orientation, load the paper so that 
the printing side is facing up as shown in the following figures.
(:  Feeding direction)
7Align the paper guides with both sides of the stack.
 

3-46Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
IMPORTANT
Be sure to align the paper guides with the width of the paper. If the paper guides 
are too loose or too tight, this may result in misfeeds or paper jams.
Next, specify the paper size for the multi-purpose tray (See p. 3-51).
Loading Envelopes in the Multi-purpose Tray
You can load envelopes at sizes of DL, COM10, C5, Monarch, and B5 in the 
mu lti-purpose tray. Use the following procedure when loading envelopes in the 
mu...

3-47Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
2Pull out the auxiliary tray.
IMPORTANT
Be sure to pull out the auxiliary tray when loading paper in the multi-purpose tray.
3When loading long-size paper such as Envelope COM10, open 
the extension tray.
 

3-48Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
4Spread the paper guides a little wider than the actual envelope 
width.
5Place the stack of envelopes on a flat surface, flatten them to 
release any remaining air, and be sure that the edges are 
pressed tightly.
CAUTION
When loading paper, take care not to cut your hands with the edges of the 
paper.
 

3-49Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
6Loosen any stiff corners of the envelopes and flatten curls as 
shown in the figure.
7Align the edges of the envelopes on a flat surface.
8Gently load the stack of envelopes with the address side 
facing up until it touches the back of the tray.
Be sure that the stack of envelopes is loaded under the paper limit guide (A)\
.
(A)
 

3-50Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
IMPORTANT
•Up to 10 envelopes can be loaded in the multi-purpose tray.
•You cannot print on the reverse side (glued side) of envelopes.
•When loading envelopes at a size of DL, COM10, C5, or Monarch, load them so 
that the flap is toward the left of the printer when viewed from the front.
•When loading envelopes of the Envelope B5 size, close the flaps and load them so 
that the envelopes are fed from the top (the edge with the flap).
 

3-51Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
9Align the paper guides with both sides of the stack.
IMPORTANT
•Make sure that there is no space between the paper guides and the envelopes, 
and be careful not to press the envelopes so hard that they are distorted. They may 
result in misfeeds or paper jams.
•Do not touch the envelopes in the multi-purpose tray or pull them out during 
printing. This may result in a faulty operation.
Next, specify the paper size for the...

3-52Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
•When you change the paper loaded in the multi-purpose tray frequently, it is convenient if 
TRAY PAPER SIZE is set to MIXED SIZES. If TRAY PAPER SIZE is set to MIXED SIZES, 
you do not need to specify the setting for TRAY PAPER SIZE each time you load the 
different size paper. However, observe the following when specifying MIXED SIZES.
- Make sure that the size of the paper loaded in the multi-purpose tray matches the paper 
size...

3-53Printing from the Multi-purpose Tray
Loading and Outputting Paper
3
4Select the paper size using [ ] and [ ], then press [OK].
= is displayed on the left of the paper size, and the paper size for the 
multi-purpose tray is specified.
When printing from the printer driver on Windows or Macintosh, configure the printer 
driver. (See Help of the printer driver)
When printing from DOS or UNIX, specify the settings for STD PAPER SIZE (See p. 
5-19) and STD PAPER TYPE (See p. 5-21) using the control panel....