Canon Ir 2200 User Guide

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-63
7-637-63 7-63
7
77 7
Handling Options
12
1212 12Close the front cover of the finisher.
Close the front cover of the finisher.Close the front cover of the finisher. Close the front cover of the finisher.
CAUTION
CAUTIONCAUTION CAUTION

 When closing the cover, be careful not to get your fingers caught, as this may result in 
When closing the cover, be careful not to get your fingers caught, as this may result in When closing the cover, be careful...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-64
7-647-64 7-64
7
77 7
Handling Options
1
11 1Open the front cover of the finisher.
Open the front cover of the finisher.Open the front cover of the finisher. Open the front cover of the finisher.
2
22 2Pull out the stapler unit.
Pull out the stapler unit.Pull out the stapler unit. Pull out the stapler unit.
3
33 3Lift and pull out the staple car tridge, holding it by its left and right sides.
Lift and pull out the staple car tridge, holding it by its...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-65
7-657-65 7-65
7
77 7
Handling Options
4
44 4Pull out the empty staple case, by pushing the area indicated by .
Pull out the empty staple case, by pushing the area indicated by .Pull out the empty staple case, by pushing the area indicated by . Pull out the empty staple case, by pushing the area indicated by .
Place the staple cartridge, as shown below, then pull out the staple case.
5
55 5Inser t the new staple case.
Inser t the new staple case.Inser...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-66
7-667-66 7-66
7
77 7
Handling Options
6
66 6Remove the seal fixing the staples, by pulling it straight out.
Remove the seal fixing the staples, by pulling it straight out.Remove the seal fixing the staples, by pulling it straight out. Remove the seal fixing the staples, by pulling it straight out.
7
77 7Push the staple car tridge back firmly into the finisher.
Push the staple car tridge back firmly into the finisher.Push the staple car tridge back...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-67
7-677-67 7-67
7
77 7
Handling Options
9
99 9Close the front cover of the finisher.
Close the front cover of the finisher.Close the front cover of the finisher. Close the front cover of the finisher.
CAUTION
CAUTIONCAUTION CAUTION

 When closing the cover, be careful not to get your fingers caught, as this may result in 
When closing the cover, be careful not to get your fingers caught, as this may result in When closing the cover, be careful not...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-68
7-687-68 7-68
7
77 7
Handling Options
CAUTION
CAUTIONCAUTION CAUTION

 When removing jammed originals or paper, take care not to cut your hands on the edges of 
When removing jammed originals or paper, take care not to cut your hands on the edges of When removing jammed originals or paper, take care not to cut your hands on the edges of  When removing jammed originals or paper, take care not to cut your hands on the edges of 
the original or...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-69
7-697-69 7-69
7
77 7
Handling Options
2
22 2Move the knob into the position (arrow showing), within the area shown in 
Move the knob into the position (arrow showing), within the area shown in Move the knob into the position (arrow showing), within the area shown in  Move the knob into the position (arrow showing), within the area shown in 
the figure.
the figure.the figure. the figure.
3
33 3Open the top cover, and remove any jammed paper.
Open the...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-70
7-707-70 7-70
7
77 7
Handling Options
5
55 5Connect the finisher to the main unit.
Connect the finisher to the main unit.Connect the finisher to the main unit. Connect the finisher to the main unit.
CAUTION
CAUTIONCAUTION CAUTION

 When retur ning the finisher to its original position, be careful not to get your fingers caught, as 
When retur ning the finisher to its original position, be careful not to get your fingers caught, as When retur ning...

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-71
7-717-71 7-71
7
77 7
Handling Options
1
11 1Move the finisher away from the main unit.
Move the finisher away from the main unit.Move the finisher away from the main unit. Move the finisher away from the main unit.
2
22 2Pull out the punch waste tray.
Pull out the punch waste tray.Pull out the punch waste tray. Pull out the punch waste tray.
3
33 3Discard the punch waste.
Discard the punch waste.Discard the punch waste. Discard the punch waste.
 

Saddle Finisher-G1/Puncher Unit-J1/Puncher Unit-G17-72
7-727-72 7-72
7
77 7
Handling Options
4
44 4Retur n the punch waste tray to its or iginal position.
Retur n the punch waste tray to its or iginal position.Retur n the punch waste tray to its or iginal position. Retur n the punch waste tray to its or iginal position.
NOTE

 If the tray is not returned securely in place, you cannot make prints with the Hole Punch mode 
selected.
5
55 5Connect the finisher to the main unit.
Connect the finisher to...