Home > Canon > Printer > Canon Imageformula Dr C225 User Guide

Canon Imageformula Dr C225 User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Canon Imageformula Dr C225 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							31
    Placing Cards
    ###HOME > Chapter 5 Placing Documents > Placing Cards###
    1Set the feed selection lever and the eject selection lever.
    Set the feed selection lever to the non separation position (upper position). The 
    feed selection indicator will light orange.
    Set the eject selection lever to the straight path position ( ).
    2Adjust the document guides to fit the width of the card to be scanned.
    3Place the card horizontally with the top edge facing upward.
    zPlace the card one at a time.
    zIf you place cards to be fed vertically, they may not be ejected 
    properly, and cards that get jammed may be damaged when you 
    remove them. Take care of the orientation when placing cards.
    zUltrasonic double feed detection will not function properly when 
    scanning cards. Clear the [Detect by Ultrasonic] check box in 
    the [Feeding] tab.
     
    						
    							32
    Placing Folded Documents
    ###HOME > Chapter 5 Placing Documents > Placing Folded 
    Documents###
    Folio Scan enables you to scan documents that are larger than LTR/
    A4 and therefore do not fit in the feeder. To use the function, fold the 
    document in half lengthwise and place it into the feeder. The 
    DR-C225 will scan both sides and combine the scanned images into 
    a single image.
    1Set the feed selection lever and the eject selection lever.
    Set the feed selection lever to the non separation position (upper position). The 
    feed selection indicator will light orange.
    Set the eject selection lever to the straight path position ( ).
    2Fold the document in half.
    Align the left and right sides of the document, and crease the document firmly. 
    If the document is not folded properly, paper jams may occur or distortions may 
    appear in the combined scanned image.
    With the straight path, documents are ejected at the front of the scanner. 
    Do not place anything that will block output near the document eject 
    area. Also, install the scanner on a smooth surface to enable documents 
    to be smoothly ejected.
    A portion of the scanned image will be missing at the fold line.
     
    						
    							33
    3Place the document in the document feed tray.
    Under default conditions, place the document with the folded edge facing right. 
    If the [Upside-down feeding] check box is selected in the scanner driver 
    settings, place the document with the folded edge facing left.
    Setting Scanning Conditions
    Configure scanning conditions as follows when scanning folded 
    documents.
    Adjust the document guides to fit the width of the document. Otherwise, 
    the image may scan as skewed or shifted.
    zThe side of the folded document that is facing forward will be 
    the left side of the combined image.
    zThe maximum size for the combined image is A2.
    Set the scanning condition for folded documents on advanced 
    settings dialog box of the scanner driver. You cannot set the 
    condition by CaptureOnTouch.
     
    						
    							34
    Scanner driver (Windows)
    Configure the following settings in the [Basic] tab. (Confirming Basic 
    Conditions for Scanning on p.64)
    zSet [Page Size] to half the size of the document (set to [Match original 
    size] when scanning an atypical document size)
    zSet [Scanning Side] to [Folio].
    Scanner driver (OS X)
    Configure the following settings. (Page Size on p.66)
    zSet [Page Size] to half the size of the document (set to [Detect 
    automatically] when scanning an atypical document size)
    zSet [Scanning Side] to [Folio].
    Setting the Long Document Mode
    ###HOME > Chapter 5 Placing Documents > Setting the Long Document 
    Mode###
    The length of documents that can be scanned with the scanner is 
    normally 356 mm (14), but you can scan documents up to 3,000 mm 
    (118.1) long by setting the scanner to the Long Document mode.
    1Start Windows and log in as a user with administrator privileges.
    2Click the Start button, and then click [All Programs], [Canon 
    DR-C225], and [Canon imageFORMULA Utility].
    imageFORMULA Utility starts.
    Note the following when using the Long Document mode:
    zWhen scanning in the Long Document mode, if the document 
    is placed on the scanner in a skewed position, it may hit the 
    edges of the feeding area and be damaged. Be careful to place 
    the document so that it is not skewed.
    zWhen scanning with the Long Document mode, paper jam 
    detection may react slowly, resulting in damage to the 
    document. Be careful to avoid paper jams.
    zWhen scanning long documents, make sure to set the feed 
    selection lever to the non separation position, and scan the 
    documents one at a time.
    zWhen scanning large-sized documents with the Long 
    Document mode, scanning may be slower. Errors may also 
    occur due to memory shortage and scanning may be disabled.
    zScanning in the Long Document mode is supported only 
    during USB connections.
     
    						
    							35
    3Click [CANON DR-C225 USB] and click [Properties].4Click the [Maintenance] tab, and then select a Long Document mode.
    Select [Long Document mode (1,000 mm)] or [Long Document mode (3,000 
    mm)] depending on the length of the document.
    5Click [OK].
    Setting Scanning Conditions
    Configure scanning conditions as follows when scanning documents in 
    Long Document mode.
    CaptureOnTouch
    Set [Page Size] to [Match original size] under [Scanner setting]. (Select 
    document settings on p.52)
    Scanner driver
    Set [Page Size] to [Match original size] in the [Basic] tab. (Confirming 
    Basic Conditions for Scanning on p.64)
     
    						
    							36
    1Opens the scanner drivers Detail Settings screen.
    See Select document settings on p.52.
    This will open the advanced settings dialog box for the scanner.
    2Click   to display the [Scanner Information] dialog box.
    The [Scanner Information] dialog box appears.
    3Click [Maintenance].
    The [Maintenance] dialog box appears.
    4Select [Long Document mode (1,000 mm)] or [Long Document mode 
    (3,000 mm)] depending on the length of the document.
    5Click   to close the dialog box.
    Setting Scanning Conditions
    Configure scanning conditions as follows when scanning documents in 
    Long Document mode.
    CaptureOnTouch
    Set [Page Size] to [Match original size] under [Scanner setting]. (Select 
    document settings on p.52)
    Scanner driver
    Set [Page Size] to [Detect automatically]. (Page Size on p.66)
     
    						
    							37
    Chapter 6 Scanning with 
    CaptureOnTouch
    ###HOME > Chapter 6 Scanning with CaptureOnTouch###
    This section describes the scanning procedure when using 
    CaptureOnTouch.
    What is CaptureOnTouch?................................................................. 37
    Starting and Exiting CaptureOnTouch.............................................. 39
    Screen Descriptions ........................................................................... 41
    Standard Scanning ............................................................................. 41
    Scanning Shortcut .............................................................................. 44
    Scanning with Start Button................................................................ 48
    Operations for the scanned image edit window .............................. 49
    Select document settings .................................................................. 52
    Setting the output ............................................................................... 54
    Scanning Shortcut setting ................................................................. 55
    About file formats ............................................................................... 55
    Environmental Settings ...................................................................... 57
    What is CaptureOnTouch?
    ###HOME > Chapter 6 Scanning with CaptureOnTouch > What is 
    CaptureOnTouch?###
    CaptureOnTouch is a scanning application that enables you to scan 
    a document with a simple operation merely by selecting the screen 
    panel.
     
    						
    							38
    CaptureOnTouch is provided with multiple scanning methods that can be 
    selected according to the purpose and application.
    CaptureOnTouch supports the following scanning methods.
    Standard Scanning
    Click the Select document and Output panels, and then click the [Scan] 
    button to scan the document. You can select the scan method according 
    to the document type and purpose of use before scanning.
    -> Standard Scanning
    Scanning Shortcut
    You can register in advance combinations of frequently-used document 
    selections and output methods as a Scanning Shortcut. Just click the 
    Scanning shortcut panel to implement the scan.
    -> Scanning Shortcut
    Start button
    Scanning shortcuts are allocated to the scanner start button in advance. 
    Set the document and press the Start button to start the scan. You can 
    also allocate your own shortcuts to the start button.
    -> Scanning with Start Button
     
    						
    							39
    Starting and Exiting CaptureOnTouch
    ###HOME > Chapter 6 Scanning with CaptureOnTouch > Starting and 
    Exiting CaptureOnTouch###
    By default, CaptureOnTouch becomes resident in the system when 
    you start your computer.
    Double-click   (CaptureOnTouch icon) in the taskbar to start 
    CaptureOnTouch and display the main window.
    zYou can also start CaptureOnTouch from the Start menu. Click 
    [Start] - [All Programs] - [Canon DR-C225] - [DR-C225 
    CaptureOnTouch].
    zThe interval between the time you press the Start button on the 
    scanner and the time scanning begins is shortened when the 
    [Make CaptureOnTouch resident] check box is selected in the 
    [Basic settings] tab of the [Environmental settings] dialog box. 
    For details, see Environmental Settings on p.57.
    Click   (CaptureOnTouch icon) in the menu bar and then click [Launch 
    CaptureOnTouch] from the menu which appears to start CaptureOnTouch 
    and display the main window.
    zThe interval between the time you press the Start button on the 
    scanner and the time scanning begins is shortened when the 
    [Make CaptureOnTouch resident] check box is selected in the 
    [Basic settings] tab of the [Environmental settings] dialog box. 
    For details, see Environmental Settings on p.57.
    Exiting CaptureOnTouch
    To close the CaptureOnTouch window, click   at the top of the window. 
    This closes the window, but CaptureOnTouch will continue to reside in the 
    system.
    To quit the CaptureOnTouch application, click   (CaptureOnTouch icon) 
    in the taskbar, and select [Exit] from the menu.
    CaptureOnTouch becomes no longer resident in the system and the icon 
    disappears from the taskbar.
     
    						
    							40
    To close the CaptureOnTouch window, click   at the top of the window. 
    This closes the window, but CaptureOnTouch will continue to reside in the 
    system.
    click   (CaptureOnTouch icon) in the menu bar, and select [Exit] from 
    the menu.
    Restarting CaptureOnTouch
    To use CaptureOnTouch after it has been made not resident in the system, 
    use one of the following procedures to restart it. CaptureOnTouch will start 
    and become resident in the system again.
    zClick [Start] - [All Programs] - [Canon DR-C225] - [DR-C225 
    CaptureOnTouch].
    zPress the Start button on the scanner (in this case, the main screen 
    of CaptureOnTouch will open and scanning will start using the scan 
    method assigned to the Start button).
    In Windows 8.1 / 8, it is registered in the following location.
    zOpen [GO] - [Applications] folder from the Finder, and double-click 
    [CaptureOnTouch DR-C225].
    zPress the Start button on the scanner (in this case, the main screen 
    of CaptureOnTouch will open and scanning will start using the scan 
    method assigned to the Start button).
    If you are using OS X 10.9, CaptureOnTouch will not start when the 
    [Start] button is pressed.
    Open [GO] - [Applications] folder from the Finder, and double-click 
    [CaptureOnTouch DR-C225].
     
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon Imageformula Dr C225 User Guide