Canon Faxphone L75 Laser Fax Printer Users Guide

Chapter 3 Registering Information3-9
Registering
Information
Setting the Daylight Saving Time
This machine supports the daylight saving time system that shifts the clock time ahead
or back according to the change in seasons. You can select whether the time
information in your machine changes to match the daylight saving time system and set
the day and time when the daylight saving time starts and ends.
1Open the one-touch speed dialing panel.
2Press Data Registration.
3Press Set.
4Use ∂or ¨to select...

3-10Registering Information Chapter 3
■If you selected ONin step 8:
9Press Setto register your selection.
10Press Setto select START DATE/TIME.
11Press Set and press ∂or ¨to select the month 
when the daylight saving time starts, and press 
Setto register your selection.
n
If you want to change your selection after pressing Set, press ¨to return to your previous
selection, make the necessary changes and press 
Set.
12Press Set and press ∂or ¨to select the week
when the daylight saving time starts, and...

Chapter 3 Registering Information3-11
Registering
Information
15Press Setto select END DATE/TIME.
16Press Setand use ∂or ¨to select the
month, week, day of the week, and 
time when the daylight saving time
ends, as in steps 11 to 14 for the START 
DATE/TIMEsettings. (e.g.OCTOBER 
LAST WEEK, SUNDAYand 02:00)
17Press Stopto return to standby mode.12/27 FaxTel
OCTOBER
MONTH
END DATE/TIME 

3-12Registering Information Chapter 3 

Chapter 4 Document Handling4-1
Document
Handling
Chapter 4
Document Handling
This chapter describes the documents you can load in your machine for sending and
copying.
Document Requirements.........................................................................4-2
Scanned Area of a Document ................................................................4-2
Loading Documents.................................................................................4-3
Adding Pages to the Document in the ADF...

4-2Document Handling Chapter 4
Document Requirements
The documents you load in the ADF for sending and copying must meet the following
requirements:
One-page document Multipage document of the 
same thickness and weight
SizeMin. 5.8 ¥4.1 in. (Min. 148 ¥105 mm) Min. 5.8 ¥4.1 in. (Min. 148 ¥105 mm)
(W ¥L)
Max. 8.5 ¥Approx. 39.4 in. Max. 8.5 ¥14 in.
(Max. 216 mm ¥Approx. 1 m) (Max. 216 ¥356 mm)
Quantity1 sheet Max. 30 letter- or A4-size sheets*
Max. 10 legal-size sheets*
Thickness0.002 to 0.009 in. (0.06 to...

Chapter 4 Document Handling4-3
Document
Handling
Loading Documents
Insert the top of your document, face  
down, into the ADF until you hear a beep 
q.
Then adjust the document guides to the 
width of the document 
w.
•Tap multipage documents on a flat surface to
even the edges before inserting them in the
ADF.
The document is now ready for scanning.
n
•For a multipage document, the pages are fed one by one from the bottom of the stack.
•Wait until all pages of your document have been scanned before...

4-4Document Handling Chapter 4
Adding Pages to the Document in the ADF
If you need to add pages to your document in the ADF, wait until the last page starts
feeding, then load up to 30 additional pages (10 legal size). The last and first page
should overlap by about one inch (2.5 cm).
1 
(2.5 cm) 

Chapter 5 Print Media Handling5-1
Print Media
Handling
Chapter 5
Print Media Handling
This chapter describes the print media you can load in your machine, and other
information related to print media and printing.
Print Media Requirements.......................................................................5-2
Printable Areas .......................................................................................5-3
Selecting and Loading Print...

5-2Print Media Handling Chapter 5
Print Media Requirements
You can load the following print media in the multi-purpose tray:
Once you have decided which paper you want to load, be sure to do the following:
•Check that the print media is compatible with your machine (1
p. 5-4).
•If you are loading paper, check that the paper size setting of the multi-purpose tray is
set for the paper size you are loading (1
p.5-9). (The default setting is letter size.)
•Check that paper delivery is set correctly for the...