Canon Fax L2000ip User Guide

Assembling the Machine
1
Before You Start Using This Machine
1-39
 When you insert the toner cartridge, make sure that the plastic knob a on the side 
of the cartridge slides vertically into the guiding groove b on the machine.
7Close the printer cover.\
IMPORTANT
 If the printer cover does not close completely, do not force it down. Remove the toner 
cartridge and insert it again.
 To avoid exposing the light-sensitive drum, never leave the printer cover open.
 The machine will not operate if the...

Assembling the Machine1-40
Before You Start Using This Machine
1
Attaching the Document Output Tray
\
IMPORTANT
 Make sure the knobs on each side of the tray fit into the holes on each side of the main unit. The back 
of the tray sits on top of the extended lip of the main unit.
Attaching the Document Feeder Tray
NOTE
 Remove the tape on the back of the tray before attaching it to the main unit.
1Slide one side into position first, then the other side.
Document Output Tray
Extended Lip
1
2
 

Assembling the Machine
1
Before You Start Using This Machine
1-41
Loading Paper into the Paper Cassettes
If your machine comes with more than one paper cassettes, you can use this procedure for 
each one.
The paper cassette can be adjusted to hold standard A or B series paper or inch-size paper, 
and can hold up to approximately 250 sheets of paper.
For high-quality printouts, we recommend using Canon standard 60 to 105 g/m
2 weight paper.
Whenever you change the paper size, you have to adjust the paper...

Assembling the Machine1-42
Before You Start Using This Machine
1
2Confirm that the paper guides inside the paper cassette are set to 
the size of the paper you are loading.
If the setting is correct, proceed to step 3.
If the setting is not correct, set the paper guides to match the size of the paper 
that you are loading.
●To change the paper size:
❏Adjust the paper size side guides in the following way:
Push the paper size side guides inward or outward to match the paper size 
that you are loading.
\...

Assembling the Machine
1
Before You Start Using This Machine
1-43
3Before you load a stack of paper into the paper cassette, tap the 
leading edge of the paper stack on a flat surface so that the 
edges are evenly aligned.
4Press down the inside plate of the paper cassette.
 

Assembling the Machine1-44
Before You Start Using This Machine
1
5Load the stack of paper into the paper cassette with the side you 
want to print on face down. Insert the stack of paper so that it fits 
neatly against the back of the paper cassette.
Paper Limit Marks
Hooks Hooks
 

Assembling the Machine
1
Before You Start Using This Machine
1-45
IMPORTANT
 Make sure that the stack of paper is below the paper limit marks and hooks at the back 
of the cassette.
 Press the paper stack down to make sure it has a clearance of approximately 1 mm from 
the hook of the paper size rear guide.
6Reinsert the paper cassette into the main unit.
Align the paper cassette with the rails on the main unit, then lift it slightly to 
insert the cassette. Slide it all the way into the main unit....

Assembling the Machine1-46
Before You Start Using This Machine
1
NOTE
 The paper volume status bar on the paper cassette indicates the level of the current 
paper supply. When you see the paper volume status bar drop, make sure you have a 
supply of paper on hand to refill the cassette. When you see the message  on the LCD display, refill the cassette.
SUPPLY REC. PAPER
Paper Volume 
Status Bar
 

Assembling the Machine
1
Before You Start Using This Machine
1-47
Connecting the Handset (Optional)
A handset is available as an option for the machine. This handset is to be used with the Canon 
FAX-L2000/L2000IP only.
1Attach the handset cradle holder to the back of the cradle with 
the screws provided.
2Fit the handset cradle holder over the holes on the main unit.
3Use the provided screws to fasten the handset cradle holder onto 
the main unit.
Bottom Top
 

Assembling the Machine1-48
Before You Start Using This Machine
1
4Connect the end of the handset connector cord to the handset 
jack marked with the handset icon ( ). Place the handset on the 
handset cradle.