Canon Eos Rebel T5i 700d Instruction Manual

321
3 Menu Settings
 Set-up 3 (Yellow)Page
 Set-up 4 (Yellow)
* During firmware updates, the touch screen will be disabled to prevent accidental 
operations.
9  My Menu  (Green)
Screen colorSelect the shooting settings screen color217
Feature guide
Enable / Disable52
Touch control
Enable / Disable55
Sensor cleaning
Auto cleaning: Enable / Disable223Clean now
Clean manually226
GPS device settings Settings available when the GPS Receiver GP-
E2 (sold separately) is attached
–
Certification Logo...

3 Menu Settings
322
 Shooting 1  (Red)Page
 Shooting 2  (Red)
 Shooting 3  (Red)
k For Movie Shooting
Image quality73  / 83  / 74  / 84  / 7 a  / 8 a / b  / c  /  
1 +73  / 188
Beep
Enable / Touch to   / Disable204
Release shutter 
without card
Enable / Disable204
Image review
Off / 2 sec. / 4 sec. / 8 sec. / Hold204
Lens aberration 
correction
Peripheral illumination: Enable / Disable129
Exposure 
compensation1/3-stop or 1/2-stop increments, ±5 stops121
Auto Lighting 
OptimizerDisable / Low / Standard /...

323
3 Menu Settings
 Movie 1 (Red)Page
 Movie 2  (Red)
* In Basic Zone modes, [ Sound recording] will be set to [On/Off].
AF method
u
+Tracking / FlexiZone - Multi / 
FlexiZone - Single196
Movie Servo AF
Enable / Disable196
AF with shutter button 
during  k
ONE SHOT / Disable197
Grid display
Off / Grid 1 l / Grid 2 m198
Metering timer4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 
30 min.198
Movie recording size
1920x1080 ( 6/5 /4 ) / 1280x720 ( 8/7 ) /
640x480 ( 6/5)185
Sound recording*
Sound...

324
If a problem occurs with the camera, first refer to this Troubleshooting 
Guide. If this Troubleshooting Guide does not resolve the problem, 
contact your dealer or nearest Canon Service Center.
  Do not recharge any battery pack other than a genuine Canon Battery 
Pack LP-E8.
  If there is a problem with the battery charger, the protective circuit will 
stop the charging operation and the charge lamp will blink in orange. If 
this happens, disconnect the charger’s power plug from the power 
outlet...

325
Troubleshooting Guide
 Use a fully-charged battery pack (p.28).
  The rechargeable battery pack performance will degrade over 
repeated use. Purchase a new one.
  The number of possible shots will decrease with any of the following 
operations:
• Pressing the shutter button halfway for a prolonged period.
• Often activating only the AF without taking a picture.
• Using the lens Image Stabilizer.
• Using the LCD monitor often.
• Continuing Live View shooting or movie shooting for a prolonged 
period....

Troubleshooting Guide
326
 Make sure the card is properly inserted (p.31).
 
Slide the card’s write-protect switch to the Write/Erase position (p.31).
  If the card is full, replace the card or delete unnecessary images 
to make room (p.31, 268).
  If you try to focus in the One-Shot AF operation while the focus 
confirmation light < o> in the viewfinder blinks, a picture cannot be 
taken. Press the shutter button halfway again to refocus automatically, 
or focus manually (p.43, 103).
  If a card error...

327
Troubleshooting Guide
 Set the AF operation to One-Shot AF. Focus lock is not possible in the 
AI Servo AF and AI Focus AF operations (p.98).
  Depending on the shooting conditions, it may take longer to focus the 
subject. Use FlexiZone - Single instead or focus manually.
  Depending on the lens type, shutter speed, aperture, subject 
conditions, brightness, etc., the continuous shooting speed may 
become slower.
  With ISO 12800 or “H ” (equivalent to ISO 25600), the maximum burst 
for continuous...

Troubleshooting Guide
328
 Under [ 54: Custom Functions (C.Fn) ], if [3: Highlight tone priority ] 
is set to [ 1: Enable ], ISO 100 cannot be set. If [ 0: Disable] is set, ISO 
100 can be set (p.299). This also applies to movie shooting (p.178).
  Under [ 54: Custom Functions (C.Fn) ], if [3: Highlight tone priority ] 
is set to [ 1: Enable ], the [H] ISO speed (25600) cannot be selected 
even when [ 2: ISO expansion ] is set to [1: On]. If [0: Disable ] is set 
for [ 3: Highlight tone priority ], [H]...

329
Troubleshooting Guide
 In the A , C, 2 , 4 , 6 , and G modes, the built-in flash will be 
raised automatically when flash is necessary.
  If you shoot continuously with the built-in flash at short intervals, the 
flash may stop operating to protect the flash unit.
  If you use a flash unit other than an EX-series Speedlite, the flash will 
always be fired at full output (p.310).
  Under [ z1: Flash control ] and [External flash C.Fn setting], if 
[ Flash metering mode ] is set to [TTL], the flash...

Troubleshooting Guide
330
 Under [ z1: Flash control ], set [Flash sync. speed in Av mode ] to 
[ Auto] (p.219).
  The built-in flash’s pop-up mechanism moves slightly. This is normal.
  If you use flash, the shutter will make two sounds each time you shoot 
(p.147).
  It indicates that the camera’s internal temperature is high. If the white 
 icon is displayed, the still photo’s image quality may deteriorate. 
If the red < E> icon is displayed, it indicates that the Live View or 
movie shooting will...